Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 | /* * Copyright (c) 2018, NXP * * SPDX-License-Identifier: Apache-2.0 */ /dts-v1/; #include <nxp/nxp_rt1060.dtsi> / { model = "NXP MIMXRT1060-EVK board"; compatible = "nxp,mimxrt1062"; aliases { led0 = &green_led; sw0 = &user_button; kscan0 = &touch_controller; watchdog0 = &wdog0; }; chosen { zephyr,flash-controller = &flexspi; zephyr,flash = &is25wp064; zephyr,code-partition = &slot0_partition; zephyr,sram = &sdram0; zephyr,itcm = &itcm; zephyr,dtcm = &dtcm; zephyr,console = &lpuart1; zephyr,shell-uart = &lpuart1; zephyr,can-primary = &flexcan2; }; sdram0: memory@80000000 { /* Micron MT48LC16M16A2B4-6AIT:G */ device_type = "memory"; reg = <0x80000000 DT_SIZE_M(32)>; }; leds { compatible = "gpio-leds"; green_led: led-1 { gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; label = "User LD1"; }; }; gpio_keys { compatible = "gpio-keys"; user_button: button-1 { label = "User SW8"; gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; }; }; arduino_header: connector { compatible = "arduino-header-r3"; #gpio-cells = <2>; gpio-map-mask = <0xffffffff 0xffffffc0>; gpio-map-pass-thru = <0 0x3f>; gpio-map = <0 0 &gpio1 26 0>, /* A0 */ <1 0 &gpio1 27 0>, /* A1 */ <2 0 &gpio1 20 0>, /* A2 */ <3 0 &gpio1 21 0>, /* A3 */ <4 0 &gpio1 17 0>, /* A4 */ <5 0 &gpio1 16 0>, /* A5 */ <6 0 &gpio1 23 0>, /* D0 */ <7 0 &gpio1 22 0>, /* D1 */ <8 0 &gpio1 11 0>, /* D2 */ <9 0 &gpio1 24 0>, /* D3 */ <10 0 &gpio1 9 0>, /* D4 */ <11 0 &gpio1 10 0>, /* D5 */ <12 0 &gpio1 18 0>, /* D6 */ <13 0 &gpio1 19 0>, /* D7 */ <14 0 &gpio1 3 0>, /* D8 */ <15 0 &gpio1 2 0>, /* D9 */ <16 0 &gpio3 13 0>, /* D10 */ <17 0 &gpio3 14 0>, /* D11 */ <18 0 &gpio3 15 0>, /* D12 */ <19 0 &gpio3 12 0>, /* D13 */ <20 0 &gpio1 17 0>, /* D14 */ <21 0 &gpio1 16 0>; /* D15 */ }; panel { compatible = "rocktech,rk043fn02h-ct"; port { lcd_panel_in: endpoint { remote-endpoint = <&lcd_panel_out>; }; }; }; }; arduino_serial: &lpuart3 {}; &flexspi { status = "okay"; ahb-prefetch; ahb-read-addr-opt; rx-clock-source = <1>; reg = <0x402a8000 0x4000>, <0x60000000 DT_SIZE_M(8)>; is25wp064: is25wp064@0 { compatible = "nxp,imx-flexspi-nor"; size = <67108864>; label = "IS25WP064"; reg = <0>; spi-max-frequency = <133000000>; status = "okay"; jedec-id = [9d 70 17]; erase-block-size = <4096>; write-block-size = <1>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; boot_partition: partition@0 { label = "mcuboot"; reg = <0x00000000 DT_SIZE_K(64)>; }; slot0_partition: partition@10000 { label = "image-0"; reg = <0x00010000 DT_SIZE_M(3)>; }; slot1_partition: partition@310000 { label = "image-1"; reg = <0x00310000 DT_SIZE_M(3)>; }; scratch_partition: partition@610000 { label = "image-scratch"; reg = <0x00610000 DT_SIZE_K(128)>; }; storage_partition: partition@630000 { label = "storage"; reg = <0x00630000 DT_SIZE_K(1856)>; }; }; }; }; &lcdif { status = "okay"; port { lcd_panel_out: endpoint { remote-endpoint = <&lcd_panel_in>; }; }; }; &lpi2c1 { status = "okay"; touch_controller: ft5336@38 { compatible = "focaltech,ft5336"; reg = <0x38>; label = "FT5336"; int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; }; }; &lpuart1 { status = "okay"; current-speed = <115200>; }; &enet { status = "okay"; ptp { status = "okay"; }; }; zephyr_udc0: &usb1 { status = "okay"; }; &usdhc1 { status = "okay"; pwr-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; status = "okay"; }; &edma0 { status = "okay"; }; &flexcan2 { status = "okay"; bus-speed = <125000>; }; &wdog0 { status = "okay"; }; |