Linux Audio

Check our new training course

Embedded Linux Audio

Check our new training course
with Creative Commons CC-BY-SA
lecture materials

Bootlin logo

Elixir Cross Referencer

Open Menu /boards/arm/stm32l496g_disco/stm32l496g_disco.dts
Loading...
  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
/*
 * Copyright (c) 2017 Linaro Limited
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;
#include <st/l4/stm32l496Xg.dtsi>
#include <st/l4/stm32l496a(e-g)ix-pinctrl.dtsi>
#include "arduino_r3_connector.dtsi"

/ {
	model = "STMicroelectronics STM32L496G-DISCO board";
	compatible = "st,stm32l496g-disco";

	chosen {
		zephyr,console = &usart2;
		zephyr,shell-uart = &usart2;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
	};

	leds {
		compatible = "gpio-leds";
		green_led_2: led_2 {
			gpios = <&gpiob 13 GPIO_ACTIVE_HIGH>;
			label = "User LD2";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		joy_sel: joystick_select {
			label = "joystick select";
			gpios = <&gpioc 13 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
		};
		joy_down: joystick_down {
			label = "joystick down";
			gpios = <&gpioi 10 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
		};
		joy_up: joystick_up {
			label = "joystick up";
			gpios = <&gpioi 8 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
		};
		joy_left: joystick_left {
			label = "joystick left";
			gpios = <&gpioi 9 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
		};
		joy_right: joystick_right {
			label = "joystick right";
			gpios = <&gpiof 11 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
		};
	};

	aliases {
		led0 = &green_led_2;
		sw0 = &joy_sel;
		sw1 = &joy_down;
		sw2 = &joy_right;
		sw3 = &joy_up;
		sw4 = &joy_left;
	};

};

&clk_hsi {
	status = "okay";
};

&pll {
	div-m = <1>;
	mul-n = <20>;
	div-p = <7>;
	div-q = <2>;
	div-r = <4>;
	clocks = <&clk_hsi>;
	status = "okay";
};

&rcc {
	clocks = <&pll>;
	clock-frequency = <DT_FREQ_M(80)>;
	ahb-prescaler = <1>;
	apb1-prescaler = <1>;
	apb2-prescaler = <1>;
};

&usart1 {
	pinctrl-0 = <&usart1_tx_pb6 &usart1_rx_pg10>;
	current-speed = <115200>;
	status = "okay";
};

&usart2 {
	pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pd6>;
	current-speed = <115200>;
	status = "okay";
};

&lpuart1 {
	pinctrl-0 = <&lpuart1_tx_pg7 &lpuart1_rx_pg8>;
	current-speed = <115200>;
	status = "okay";
};

&timers2 {
	status = "okay";

	pwm2: pwm {
		status = "okay";
		pinctrl-0 = <&tim2_ch1_pa0>;
	};
};

&i2c1 {
	pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb7>;
	status = "okay";
	clock-frequency = <I2C_BITRATE_FAST>;
};

&spi1 {
	pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pb4 &spi1_mosi_pb5>;
	cs-gpios = <&gpioa 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
	status = "okay";
};

&rtc {
	status = "okay";
};

&sdmmc1 {
	pinctrl-0 = <&sdmmc1_d0_pc8 &sdmmc1_d1_pc9
		     &sdmmc1_d2_pc10 &sdmmc1_d3_pc11
		     &sdmmc1_ck_pc12 &sdmmc1_cmd_pd2>;
	status = "okay";
};

&adc1 {
	pinctrl-0 = < &adc1_in2_pc1>;
	status = "okay";
};