Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 | # USB device configuration options # Copyright (c) 2016 Wind River Systems, Inc. # SPDX-License-Identifier: Apache-2.0 menuconfig USB_DEVICE_DRIVER bool "Enable USB device controller drivers" help Enable USB device controller drivers. if USB_DEVICE_DRIVER config USB_DW bool "Designware USB Device Controller Driver" help Designware USB Device Controller Driver. config USB_DW_USB_2_0 bool "DesignWare Controller and PHY support for USB specification 2.0" depends on USB_DW help Indicates whether or not USB specification version 2.0 is supported config USB_DC_STM32 bool "USB device controller driver for STM32 devices" depends on SOC_FAMILY_STM32 select USE_STM32_LL_USB select USE_STM32_HAL_PCD select USE_STM32_HAL_PCD_EX help Enable USB support on the STM32 F0, F1, F2, F3, F4, F7, L0, L4 and G4 family of processors. config USB_DC_STM32_DISCONN_ENABLE bool depends on USB_DC_STM32 help Say Y if your board uses USB DISCONNECT pin to enable the pull-up resistor on USB DP. config USB_DC_SAM0 bool "SAM0 series USB Device Controller driver" default y depends on SOC_FAMILY_SAM0 help SAM0 family USB device controller Driver. DT_COMPAT_SAM_USBC := atmel,sam-usbc config USB_DC_SAM_USBC bool "SAM4L USBC Device Controller driver" depends on SOC_SERIES_SAM4L default $(dt_compat_enabled,$(DT_COMPAT_SAM_USBC)) help SAM4L family USBC device controller Driver. config USB_DC_SAM_USBHS bool "SAM series USB HS Device Controller driver" depends on SOC_SERIES_SAME70 || \ SOC_SERIES_SAMV71 help SAM family USB HS device controller Driver. config USB_NRFX bool "Nordic Semiconductor USB Device Controller Driver" default y depends on HAS_HW_NRF_USBD select NRFX_USBD select NRFX_POWER help nRF USB Device Controller Driver config USB_NRFX_EVT_QUEUE_SIZE int "USBD event queue size" range 4 64 default 32 depends on USB_NRFX help Size of the driver's internal event queue. Required size will depend on number of endpoints (class instances) in use. config USB_NRFX_WORK_QUEUE_STACK_SIZE int "USBD work queue stack size" default 1024 depends on USB_NRFX help Size of the stack for the work queue thread that is used in the driver for handling the events from the USBD ISR, i.e. executing endpoint callbacks and providing proper notifications to the USB device stack. config USB_NRFX_ATTACHED_EVENT_DELAY int "USBD attached event delay" range 0 1000 default 0 depends on USB_NRFX help Configurable attached event delay in milliseconds. Delay can be used to give USB Charging Controller time for initialization. config USB_KINETIS bool "Kinetis USB Device Controller Driver" help Kinetis USB Device Controller Driver. config USB_MCUX bool "NXP MCUX USB Device Controller Driver" help NXP MCUX USB Device Controller Driver for MXRT and LPC SoC's. if USB_MCUX choice USB_MCUX_CONTROLLER_TYPE prompt "USB Controller type" help Select the type of controller available in the SoC. config USB_DC_NXP_EHCI bool "MXRT EHCI USB Device Controller" select NOCACHE_MEMORY if HAS_MCUX_CACHE help Kinetis and RT EHCI USB Device Controller Driver. config USB_DC_NXP_LPCIP3511 bool "LPC USB Device Controller" help LPC USB Device Controller Driver. endchoice endif # USB_MCUX config USB_NATIVE_POSIX bool "Native Posix USB Device Controller Driver" help Native Posix USB Device Controller Driver. module = USB_DRIVER module-str = usb driver source "subsys/logging/Kconfig.template.log_config" endif # USB_DEVICE_DRIVER |