Linux preempt-rt

Check our new training course

Real-Time Linux with PREEMPT_RT

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

/*
 * Copyright (c) ITE, All Rights Reserved
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;

#include <it8xxx2.dtsi>
#include <it8xxx2-alts-map.dtsi>

/ {
	model = "IT8XXX2 EV-Board";
	compatible = "riscv,it8xxx2-evb";

	aliases {
		pwm-led0 = &led0;
		pwm-led1 = &led1;
	};

	chosen {
		zephyr,console = &uart1;
		zephyr,shell-uart = &uart1;
		zephyr,bt-uart = &uart2;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,flash-controller = &flashctrl;
		zephyr,code-partition = &slot0_partition;
	};

	pwmleds {
		compatible = "pwm-leds";
		/* NOTE: &pwm number needs same with channel number */
		led0: led_0 {
			pwms = <&pwm7 PWM_CHANNEL_7 PWM_POLARITY_INVERTED>;
			label = "LED0_GREEN";
		};
		led1: led_1 {
			pwms = <&pwm0 PWM_CHANNEL_0 PWM_POLARITY_NORMAL>;
			label = "LED1_BLUE";
		};
	};
};
&adc0 {
	status = "okay";
};
&i2c0 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&i2c1 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&i2c2 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&i2c3 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&i2c4 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&i2c5 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_STANDARD>;
};
&uart1 {
	status = "okay";
	current-speed = <115200>;
	clock-frequency = <1804800>;
};
&uart2 {
	status = "okay";
	current-speed = <460800>;
	clock-frequency = <1804800>;
};
&pwm0 {
	status = "okay";
	prescaler-cx = <PWM_PRESCALER_C6>;
	/*
	 * If we need pwm output in ITE chip power saving mode,
	 * then we should set frequency <=324Hz.
	 */
	pwm-output-frequency = <324>;
};
&pwm7 {
	status = "okay";
	prescaler-cx = <PWM_PRESCALER_C4>;
	pwm-output-frequency = <30000>;
};
&flash0 {
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;
		boot_partition: partition@0 {
			label = "mcuboot";
			reg = <0x00000000 0x20000>;
		};
		slot0_partition: partition@20000 {
			label = "image-0";
			reg = <0x00020000 0x20000>;
		};
		slot1_partition: partition@40000 {
			label = "image-1";
			reg = <0x00040000 0x10000>;
		};
		scratch_partition: partition@50000 {
			label = "image-scratch";
			reg = <0x00050000 0x10000>;
		};
		storage_partition: partition@60000 {
			label = "storage";
			reg = <0x00060000 0x20000>;
		};
	};
};