Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 | .. _olimexino_stm32:
OLIMEXINO-STM32
###############
Overview
********
The OLIMEXINO-STM32 board is based on the STMicroelectronics STM32F103RB ARM
Cortex-M3 CPU.
.. figure:: img/olimexino_stm32.png
:width: 540px
:align: center
:height: 454px
:alt: OLIMEXINO-STM32
OLIMEXINO-STM32
More information about the board can be found at the
`OLIMEXINO-STM32 website`_ and `OLIMEXINO-STM32 user manual`_.
The `ST STM32F103xB Datasheet`_ contains the processor's
information and the datasheet.
Supported Features
==================
The olimexino_stm32 board configuration supports the following
hardware features:
+-----------+------------+-------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=========================+
| NVIC | on-chip | nested vectored |
| | | interrupt controller |
+-----------+------------+-------------------------+
| SYSTICK | on-chip | system clock |
+-----------+------------+-------------------------+
| UART | on-chip | serial port |
+-----------+------------+-------------------------+
| GPIO | on-chip | gpio |
+-----------+------------+-------------------------+
| I2C | on-chip | i2c |
+-----------+------------+-------------------------+
| SPI | on-chip | spi |
+-----------+------------+-------------------------+
| USB | on-chip | USB device |
+-----------+------------+-------------------------+
| WATCHDOG | on-chip | independent watchdog |
+-----------+------------+-------------------------+
| CAN | on-chip | Controller Area Network |
+-----------+------------+-------------------------+
Other hardware features are not supported by the Zephyr kernel.
Pin Mapping
===========
.. figure:: img/olimexino-stm32-front.png
:width: 739px
:align: center
:height: 530px
:alt: OLIMEXINO-STM32 connectors
OLIMEXINO-STM32 connectors
LED
---
* LED1 (green) = PA5
* LED2 (yellow) = PA1
* PWR_LED (red) = power
Push buttons
------------
* BUT = PC9 / TIM3CH4 / BOOT0
* RST = NRST
External Connectors
-------------------
SWD
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | VCC | N/A |
+-------+--------------+-------------------------+
| 2 | TMS / SWDIO | JTMS / SWDIO / PA13 |
+-------+--------------+-------------------------+
| 3 | GND | N/A |
+-------+--------------+-------------------------+
| 4 | TCK / SWCLK | JTCK / SWCLK / PA14 |
+-------+--------------+-------------------------+
| 5 | GND | N/A |
+-------+--------------+-------------------------+
| 6 | TDO / SWO | JTDO /TIM2_CH2 / PB3 / |
| | | TRACESWO / SPI1_SCK |
+-------+--------------+-------------------------+
| 7 | Cut off | N/A |
+-------+--------------+-------------------------+
| 8 | TDI | JTDI / TIM2_CH1_ETR / |
| | | PA15 / SPI1_NSS |
+-------+--------------+-------------------------+
| 9 | GND | N/A |
+-------+--------------+-------------------------+
| 10 | RESET | NRST |
+-------+--------------+-------------------------+
UEXT
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | VCC | N/A |
+-------+--------------+-------------------------+
| 2 | GND | N/A |
+-------+--------------+-------------------------+
| 3 | D7 (TXD1) | PA9 / USART1_TX / |
| | | TIM1_CH2 |
+-------+--------------+-------------------------+
| 4 | D8 (RXD1) | PA10 / USART1_RX / |
| | | TIM1_CH3 |
+-------+--------------+-------------------------+
| 5 | D29 (SCL2) | PB10 / I2C2_SCL / |
| | | USART3_TX / TIM2_CH3 |
+-------+--------------+-------------------------+
| 6 | D30 (SDA2) | PB11 / I2C2_SDA / |
| | | USART3_RX / TIM2_CH4 |
+-------+--------------+-------------------------+
| 7 | D12 (MISO1) | PA6 / SPI1_MISO / |
| | | ADC12_IN6 / TIM3_CH1 / |
| | | TIM1_BKIN |
+-------+--------------+-------------------------+
| 8 | D11 (MOSI1) | PA7 / SPI1_MOSI / |
| | | ADC12_IN7 / TIM3_CH2 / |
| | | TIM1_CH1N |
+-------+--------------+-------------------------+
| 9 | D13 (SCK / | PA5 / SPI1_SCK / |
| | LED1) | ADC12_IN5 |
+-------+--------------+-------------------------+
| 10 | UEXT_#CS | N/A |
+-------+--------------+-------------------------+
EXT
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | D23_EXT | PC15 / OSC32_OUT |
+-------+--------------+-------------------------+
| 2 | D24 (CANTX) | PB9 / TIM4_CH4 / |
| | | I2C1_SDA / CANTX |
+-------+--------------+-------------------------+
| 3 | D25 (MMC_CS) | PD2 / TIM3_ETR |
+-------+--------------+-------------------------+
| 4 | D26 | PC10 / USART3_TX |
+-------+--------------+-------------------------+
| 5 | D27 | PB0 / ADC12_IN8 / |
| | | TIM3_CH3 / TIM1_CH2N |
+-------+--------------+-------------------------+
| 6 | D28 | PB1 / ADC12_IN9 / |
| | | TIM3_CH4 / TIM1_CH3N |
+-------+--------------+-------------------------+
| 7 | D29 (SCL2) | PB10 / I2C2_SCL / |
| | | USART3_TX / TIM2_CH3 |
+-------+--------------+-------------------------+
| 8 | D30 (SDA2) | PB11 / I2C2_SDA / |
| | | USART3_RX / TIM2_CH4 |
+-------+--------------+-------------------------+
| 9 | D31 (#SS2) | PB12 / SPI2_NSS / |
| | | I2C2_SMBAI / USART3_CK /|
| | | TIM1_BKIN |
+-------+--------------+-------------------------+
| 10 | D32 (SCK2) | PB13 / SPI2_SCK/ |
| | | USART3_CTS / TIM1_CH1N |
+-------+--------------+-------------------------+
| 11 | D33 (MISO2) | PB14 / SPI2_MISO / |
| | | USART3_RTS / TIM1_CH2N |
+-------+--------------+-------------------------+
| 12 | D34 (MOSI2) | PB15 / SPI2_MOSI / |
| | | TIM1_CH3N |
+-------+--------------+-------------------------+
| 13 | D35 | PC6 / TIM3_CH1 |
+-------+--------------+-------------------------+
| 14 | D36 | PC7 / TIM3_CH2 |
+-------+--------------+-------------------------+
| 15 | D37 | PC8 / TIM3_CH3 |
+-------+--------------+-------------------------+
| 16 | GND | N/A |
+-------+--------------+-------------------------+
Arduino Headers
---------------
CON1 power
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | RESET | NRST |
+-------+--------------+-------------------------+
| 2 | VCC (3V3) | N/A |
+-------+--------------+-------------------------+
| 3 | VDD (3V3A) | N/A |
+-------+--------------+-------------------------+
| 4 | GND | N/A |
+-------+--------------+-------------------------+
| 5 | GND | N/A |
+-------+--------------+-------------------------+
| 6 | VIN | N/A |
+-------+--------------+-------------------------+
CON2 analog
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | D15 (A0) | PC0 / ADC12_IN10 |
+-------+--------------+-------------------------+
| 2 | D16 (A1) | PC1 / ADC12_IN11 |
+-------+--------------+-------------------------+
| 3 | D17 (A2) | PC2 / ADC12_IN12 |
+-------+--------------+-------------------------+
| 4 | D18 (A3) | PC3 / ADC12_IN13 |
+-------+--------------+-------------------------+
| 5 | D19 (A4) | PC4 / ADC12_IN14 |
+-------+--------------+-------------------------+
| 6 | D20 (A5) | PC5 / ADC12_IN15 |
+-------+--------------+-------------------------+
CON3 digital
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | D0 (RXD2) | PA3 / USART2_RX / |
| | | ADC12_IN3 / TIM2_CH4 |
+-------+--------------+-------------------------+
| 2 | D1 (TXD2) | PA2 / USART2_TX / |
| | | ADC12_IN2 / TIM2_CH3 |
+-------+--------------+-------------------------+
| 3 | D2 | PA0 / WKUP / |
| | | USART2_CTS / ADC12_IN0 /|
| | | TIM2_CH1 |
+-------+--------------+-------------------------+
| 4 | D3 (LED2) | PA1 / USART2_RTS / |
| | | ADC12_IN1 / TIM2_CH2 |
+-------+--------------+-------------------------+
| 5 | D4 | PB5 / I2C1_SMBAI / |
| | | TIM3_CH2 / SPI1_MOSI |
+-------+--------------+-------------------------+
| 6 | D5 | PB6 / I2C1_SCL / |
| | | TIM4_CH1 / USART1_TX |
+-------+--------------+-------------------------+
| 7 | D6 | PA8 / USART1_CK / |
| | | TIM1_CH1 / MCO |
+-------+--------------+-------------------------+
| 8 | D7 (TXD1) | PA9 / USART1_TX / |
| | | TIM1_CH2 |
+-------+--------------+-------------------------+
CON4 digital
+-------+--------------+-------------------------+
| PIN # | Signal Name | STM32F103RB Functions |
+=======+==============+=========================+
| 1 | D8 (RXD1) | PA10 / USART1_RX / |
| | | TIM1_CH3 |
+-------+--------------+-------------------------+
| 2 | D9 | PB7 / I2C1_SDA / |
| | | TIM4_CH2 / USART1_RX |
+-------+--------------+-------------------------+
| 3 | D10 (#SS1) | PA4 / SPI1_NSS / |
| | | USART2_CK / ADC12_IN4 |
+-------+--------------+-------------------------+
| 4 | D11 (MOSI1) | PA7 / SPI1_MOSI / |
| | | ADC12_IN7 / TIM3_CH2 / |
| | | TIM1_CH1N |
+-------+--------------+-------------------------+
| 5 | D12 (MISO1) | PA6 / SPI1_MISO / |
| | | ADC12_IN6 / TIM3_CH1 / |
| | | TIM1_BKIN |
+-------+--------------+-------------------------+
| 6 | D13 (SCK1 / | PA5 / SPI1_SCK / |
| | LED1) | ADC12_IN5 |
+-------+--------------+-------------------------+
| 7 | GND | N/A |
+-------+--------------+-------------------------+
| 8 | D14 (CANRX) | PB8 / TIM4_CH3 / |
| | | I2C1_SCL / CANRX |
+-------+--------------+-------------------------+
CAN
+-------+-------------+
| PIN # | Signal Name |
+=======+=============+
| 1 | GND |
+-------+-------------+
| 2 | CAN L |
+-------+-------------+
| 3 | CAN H |
+-------+-------------+
System Clock
============
OLIMEXINO-STM32 has two external oscillators. The frequency of
the slow clock is 32.768 kHz. The frequency of the main clock
is 8 MHz. The processor can setup HSE to drive the master clock,
which can be set as high as 72 MHz.
Serial Port
===========
OLIMEXINO-STM32 board has up to 3 U(S)ARTs. The Zephyr console output is
assigned to USART1. Default settings are 115200 8N1.
SPI
===
OLIMEXINO-STM32 board has up to 2 SPIs. The default SPI mapping for Zephyr is:
- SPI1_NSS : PA4
- SPI1_SCK : PA5
- SPI1_MISO : PA6
- SPI1_MOSI : PA7
I2C
===
The OLIMEXINO-STM32 board supports two I2C devices. The default I2C mapping for
Zephyr is:
- I2C1_SCL : PB6
- I2C1_SDA : PB7
- I2C2_SCL : PB10
- I2C2_SDA : PB11
USB
===
OLIMEXINO-STM32 board has a USB 2.0 full-speed device interface available
through its mini USB connector.
- USB_DM : PA11
- USB_DP : PA12
CAN
===
OLIMEXINO-STM32 board has a CAN interface with transceiver on board.
CAN is accessible through a screw terminal.
- CAN_RX : PB8
- CAN_TX : PB9
Jumpers
=======
The Zephyr kernel uses the OLIMEXINO-STM32 default jumper
settings. Note that all jumpers on the board are SMD type.
You will need to solder, unsolder, or cut them in order to
reconfigure them.
The default jumper settings for the OLIMEXIMO-STM32E are:
+---------------+------------+---------------+
| Jumper Name | Open | Close |
+===============+============+===============+
| LED1_E | | x |
+---------------+------------+---------------+
| LED2_E | | x |
+---------------+------------+---------------+
| D23_E | x | |
+---------------+------------+---------------+
| R-T | x | |
+---------------+------------+---------------+
| P10_E | | x |
+---------------+------------+---------------+
+---------------+------------+---------------+
| Jumper Name | D10 | D4 |
+===============+============+===============+
| D10/D4 | | x |
+---------------+------------+---------------+
Flashing Zephyr onto OLIMEXINO-STM32
************************************
Flashing the Zephyr kernel onto OLIMEXINO-STM32 requires the
`stm32flash tool`_.
Building stm32flash command line tool
=====================================
To build the stm32flash tool, follow the steps below:
#. Checkout the stm32flash tool's code from the repository.
.. code-block:: console
$ git clone http://git.code.sf.net/p/stm32flash/code stm32flash
$ cd stm32flash
#. Build the stm32flash tool.
.. code-block:: console
$ make
#. The resulting binary is available at :file:`stm32flash`.
Flashing an Application to OLIMEXINO-STM32
==========================================
To upload an application to the OLIMEXINO-STM32 board a TTL(3.3V)
serial adapter is required. This tutorial uses the
:ref:`button-sample` sample application.
#. Connect the serial cable to the UEXT lines of the UART
interface (pin #3=TX and pin #4=RX).
#. Power the OLIMEXINO-STM32 via the mini USB.
#. Reset the board while holding the button (BUT).
#. To build the application and flash it, enter:
.. zephyr-app-commands::
:zephyr-app: samples/basic/button
:board: olimexino_stm32
:goals: flash
#. Run your favorite terminal program to listen for output.
.. code-block:: console
$ minicom -D /dev/ttyUSB0 -b 115200
The :code:`-b` option sets baud rate ignoring the value
from config.
#. Press the Reset button and you should see the output of
button application in your terminal. The state of the BUT
button's GPIO line is monitored and printed to the serial
console. When the input button gets pressed, the interrupt
handler prints information about this event along with its
timestamp.
.. note::
Make sure your terminal program is closed before flashing
the binary image, or it will interfere with the flashing
process.
.. _OLIMEXINO-STM32 website:
https://www.olimex.com/Products/Duino/STM32/OLIMEXINO-STM32/
.. _OLIMEXINO-STM32 user manual:
https://www.olimex.com/Products/Duino/STM32/OLIMEXINO-STM32/resources/OLIMEXINO-STM32.pdf
.. _ST STM32F103xB Datasheet:
http://www.st.com/resource/en/datasheet/stm32f103tb.pdf
.. _stm32flash tool:
https://sourceforge.net/p/stm32flash/wiki/Home/
|