Linux preempt-rt

Check our new training course

Real-Time Linux with PREEMPT_RT

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

# Copyright (c) 2021 Nordic Semiconductor ASA
# SPDX-License-Identifier: Apache-2.0

menu "Backends"

config LOG_BACKEND_UART
	bool "Enable UART backend"
	depends on UART_CONSOLE
	default y if !SHELL_BACKEND_SERIAL
	help
	  When enabled backend is using UART to output logs.

config LOG_BACKEND_UART_SYST_ENABLE
	bool "Enable UART syst backend"
	depends on LOG_BACKEND_UART
	depends on LOG_MIPI_SYST_ENABLE
	help
	  When enabled backend is using UART to output syst format logs.

config LOG_BACKEND_SWO
	bool "Enable Serial Wire Output (SWO) backend"
	depends on HAS_SWO
	help
	  When enabled, backend will use SWO for logging.

if LOG_BACKEND_SWO

config LOG_BACKEND_SWO_FREQ_HZ
	int "Set SWO output frequency"
	default 0
	help
	  Set SWO output frequency. Value 0 will select maximum frequency
	  supported by the given MCU. Not all debug probes support high
	  frequency SWO operation. In this case the frequency has to be set
	  manually.

	  SWO value defined by this option will be configured at boot. Most SWO
	  viewer programs will configure SWO frequency when attached to the
	  debug probe. Such configuration will persist only until the device
	  reset. To ensure flawless operation the frequency configured here and
	  by the SWO viewer program has to match.

config LOG_BACKEND_SWO_SYST_ENABLE
	bool "Enable SWO syst backend"
	depends on LOG_MIPI_SYST_ENABLE
	help
	  When enabled backend is using SWO to output syst format logs.

endif # LOG_BACKEND_SWO

config LOG_BACKEND_RTT
	bool "Enable Segger J-Link RTT backend"
	depends on USE_SEGGER_RTT
	default y if !SHELL_BACKEND_RTT
	help
	  When enabled, backend will use RTT for logging. This backend works on a per
	  message basis. Only a whole message (terminated with a carriage return: '\r')
	  is transferred to up-buffer at once depending on available space and
	  selected mode.
	  In panic mode backend always blocks and waits until there is space
	  in up-buffer for a message and message is transferred to host.

if LOG_BACKEND_RTT

choice
	prompt "Logger behavior"
	default LOG_BACKEND_RTT_MODE_BLOCK

config LOG_BACKEND_RTT_MODE_DROP
	bool "Drop messages that do not fit in up-buffer."
	help
	  If there is not enough space in up-buffer for a message, drop it.
	  Number of dropped messages will be logged.
	  Increase up-buffer size helps to reduce dropping of messages.

config LOG_BACKEND_RTT_MODE_BLOCK
	bool "Block until message is transferred to host."
	help
	  Waits until there is enough space in the up-buffer for a message.

config LOG_BACKEND_RTT_SYST_ENABLE
	bool "Enable RTT syst backend"
	depends on LOG_MIPI_SYST_ENABLE
	help
	  When enabled backend is using RTT to output syst format logs.

endchoice

config LOG_BACKEND_RTT_MESSAGE_SIZE
	int "Size of internal buffer for storing messages."
	range 32 256
	default 128
	depends on LOG_BACKEND_RTT_MODE_DROP
	help
	  This option defines maximum message size transferable to up-buffer.

if LOG_BACKEND_RTT_MODE_BLOCK

config LOG_BACKEND_RTT_OUTPUT_BUFFER_SIZE
	int "Size of the output buffer"
	default 16
	help
	  Buffer is used by log_output module for preparing output data (e.g.
	  string formatting).

config LOG_BACKEND_RTT_RETRY_CNT
	int "Number of retries"
	default 4
	help
	  Number of TX retries before dropping the data and assuming that
	  RTT session is inactive.

config LOG_BACKEND_RTT_RETRY_DELAY_MS
	int "Delay between TX retries in milliseconds"
	default 5
	help
	  Sleep period between TX retry attempts. During RTT session, host pulls
	  data periodically. Period starts from 1-2 milliseconds and can be
	  increased if traffic on RTT increases (also from host to device). In
	  case of heavy traffic data can be lost and it may be necessary to
	  increase delay or number of retries.

endif # LOG_BACKEND_RTT_MODE_BLOCK

config LOG_BACKEND_RTT_BUFFER
	int "Buffer number used for logger output."
	range 0 SEGGER_RTT_MAX_NUM_UP_BUFFERS
	default 0
	help
	  Select index of up-buffer used for logger output, by default it uses
	  terminal up-buffer and its settings.

config LOG_BACKEND_RTT_BUFFER_SIZE
	int "Size of reserved up-buffer for logger output."
	default 1024
	depends on LOG_BACKEND_RTT_BUFFER > 0
	help
	  Specify reserved size of up-buffer used for logger output.

# Enable processing of printk calls using log if terminal buffer is used.
# Same buffer is used by RTT console. If printk would go through RTT console
# that will lead to corruption of RTT data which is not protected against being
# interrupted by an interrupt.
config LOG_BACKEND_RTT_FORCE_PRINTK
	bool
	default y if LOG_BACKEND_RTT_BUFFER = 0 && RTT_CONSOLE
	select LOG_PRINTK

endif # LOG_BACKEND_RTT

config LOG_BACKEND_SPINEL
	bool "Enable OpenThread dedicated Spinel protocol backend"
	depends on (OPENTHREAD_COPROCESSOR_SPINEL_ON_UART_DEV_NAME!=UART_CONSOLE_ON_DEV_NAME || !LOG_BACKEND_UART)
	depends on NET_L2_OPENTHREAD
	help
	  When enabled, backend will use OpenThread dedicated SPINEL protocol for logging.
	  This protocol is byte oriented and wrapps given messages into serial frames.
	  Backend should be enabled only to OpenThread purposes and when UART backend is disabled
	  or works on antoher UART device to avoid interference.

if LOG_BACKEND_SPINEL

config LOG_BACKEND_SPINEL_BUFFER_SIZE
	int "Size of reserved up-buffer for logger output."
	default 64
	help
	  Specify reserved size of up-buffer used for logger output.

endif # LOG_BACKEND_SPINEL

config LOG_BACKEND_NATIVE_POSIX
	bool "Enable native backend"
	depends on ARCH_POSIX
	help
	  Enable backend in native_posix

config LOG_BACKEND_XTENSA_SIM
	bool "Enable xtensa simulator backend"
	depends on SOC_XTENSA_SAMPLE_CONTROLLER || SOC_FAMILY_INTEL_ADSP
	help
	  Enable backend in xtensa simulator

config LOG_BACKEND_XTENSA_OUTPUT_BUFFER_SIZE
	int "Size of the output buffer"
	default 16
	depends on LOG_BACKEND_XTENSA_SIM
	help
	  Buffer is used by log_output module for preparing output data (e.g.
	  string formatting).

# Immediate mode cannot be used with network backend as it would cause the sent
# rsyslog message to be malformed.
config LOG_BACKEND_NET
	bool "Enable networking backend"
	depends on NETWORKING && NET_UDP && !LOG_IMMEDIATE
	select NET_CONTEXT_NET_PKT_POOL
	help
	  Send syslog messages to network server.
	  See RFC 5424 (syslog protocol) and RFC 5426 (syslog over UDP)
	  specifications for details.

if LOG_BACKEND_NET

config LOG_BACKEND_NET_SERVER
	string "Syslog server IP address"
	help
	  This can be either IPv4 or IPv6 address.
	  Server listen UDP port number can be configured here too.
	  Following syntax is supported:
	  192.0.2.1:514
	  192.0.2.42
	  [2001:db8::1]:514
	  [2001:db8::2]
	  2001:db::42

config LOG_BACKEND_NET_MAX_BUF
	int "How many network buffers to allocate for sending messages"
	range 3 256
	default 3
	help
	  Each syslog message should fit into a network packet that will be
	  sent to server. This number tells how many syslog messages can be
	  in transit to the server.

config LOG_BACKEND_NET_MAX_BUF_SIZE
	int "Max syslog message size"
	range 64 1180
	default 1180 if NET_IPV6
	default 480 if NET_IPV4
	default 256
	help
	  As each syslog message needs to fit to UDP packet, set this value
	  so that messages are not truncated.
	  The RFC 5426 recommends that for IPv4 the size is 480 octets and for
	  IPv6 the size is 1180 octets. As each buffer will use RAM, the value
	  should be selected so that typical messages will fit the buffer.

config LOG_BACKEND_NET_SYST_ENABLE
	bool "Enable networking syst backend"
	depends on LOG_MIPI_SYST_ENABLE
	help
	  When enabled backend is using networking to output syst format logs.

config LOG_BACKEND_NET_AUTOSTART
	bool "Automatically start networking backend"
	default y if NET_CONFIG_NEED_IPV4 || NET_CONFIG_NEED_IPV6
	help
	  When enabled automatically start the networking backend on
	  application start. If no routes to the logging server are available
	  on application startup, this must be set to n and the backend must be
	  started by the application later on. Otherwise the logging
	  thread might block.

endif # LOG_BACKEND_NET

config LOG_BACKEND_ADSP
	bool "Enable Intel ADSP buffer backend"
	depends on SOC_FAMILY_INTEL_ADSP
	help
	  Enable backend for the host trace protocol of the Intel ADSP
	  family of audio processors

endmenu