Linux preempt-rt

Check our new training course

Real-Time Linux with PREEMPT_RT

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

/*
 *
 * Copyright (c) 2017 Linaro Limited.
 *
 * SPDX-License-Identifier: Apache-2.0
 */


#include <soc.h>
#include <stm32_ll_bus.h>
#include <stm32_ll_pwr.h>
#include <stm32_ll_rcc.h>
#include <stm32_ll_utils.h>
#include <drivers/clock_control.h>
#include <sys/util.h>
#include <drivers/clock_control/stm32_clock_control.h>
#include "clock_stm32_ll_common.h"
#include "stm32_hsem.h"

#ifdef CONFIG_CLOCK_STM32_SYSCLK_SRC_PLL

/* Macros to fill up division factors values */
#define z_pllm(v) LL_RCC_PLLM_DIV_ ## v
#define pllm(v) z_pllm(v)

#define z_pllr(v) LL_RCC_PLLR_DIV_ ## v
#define pllr(v) z_pllr(v)

/**
 * @brief fill in pll configuration structure
 */
void config_pll_init(LL_UTILS_PLLInitTypeDef *pllinit)
{
	pllinit->PLLM = pllm(CONFIG_CLOCK_STM32_PLL_M_DIVISOR);
	pllinit->PLLN = CONFIG_CLOCK_STM32_PLL_N_MULTIPLIER;
	pllinit->PLLR = pllr(CONFIG_CLOCK_STM32_PLL_R_DIVISOR);
#ifdef PWR_CR5_R1MODE
	/* set power boost mode for sys clock greater than 80MHz */
	if (sys_clock_hw_cycles_per_sec() >= MHZ(80)) {
		LL_PWR_EnableRange1BoostMode();
	}
#endif /* PWR_CR5_R1MODE */
}
#endif /* CONFIG_CLOCK_STM32_SYSCLK_SRC_PLL */

/**
 * @brief Activate default clocks
 */
void config_enable_default_clocks(void)
{
#ifdef CONFIG_CLOCK_STM32_LSE
	/* LSE belongs to the back-up domain, enable access.*/

#if defined(CONFIG_SOC_SERIES_STM32WBX)
	/* HW semaphore Clock enable */
	LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_HSEM);
#endif
	z_stm32_hsem_lock(CFG_HW_RCC_SEMID, HSEM_LOCK_DEFAULT_RETRY);

#ifdef LL_APB1_GRP1_PERIPH_PWR
	/* Enable the power interface clock */
	LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR);
#endif

	/* Set the DBP bit in the Power control register 1 (PWR_CR1) */
	LL_PWR_EnableBkUpAccess();
	while (!LL_PWR_IsEnabledBkUpAccess()) {
		/* Wait for Backup domain access */
	}

	/* Enable LSE Oscillator (32.768 kHz) */
	LL_RCC_LSE_Enable();
	while (!LL_RCC_LSE_IsReady()) {
		/* Wait for LSE ready */
	}

	LL_PWR_DisableBkUpAccess();

	z_stm32_hsem_unlock(CFG_HW_RCC_SEMID);

#endif
}