Linux Audio

Check our new training course

Loading...
/*
 * Copyright (c) 2018 Bryan O'Donoghue
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <init.h>
#include <drivers/pinmux.h>
#include <soc.h>

static int board_pinmux_init(struct device *dev)
{
	struct device *muxa = device_get_binding(DT_LABEL(DT_NODELABEL(pinmux_a)));
	struct device *muxb = device_get_binding(DT_LABEL(DT_NODELABEL(pinmux_b)));

	ARG_UNUSED(dev);

#if (ATMEL_SAM0_DT_SERCOM_CHECK(0, atmel_sam0_uart) && CONFIG_UART_SAM0)
	/* SERCOM0 on RX=PA11, TX=PA10 */
	pinmux_pin_set(muxa, 11, PINMUX_FUNC_C);
	pinmux_pin_set(muxa, 10, PINMUX_FUNC_C);
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(1, atmel_sam0_uart) && CONFIG_UART_SAM0)
	/* SERCOM3 ON RX=PA19, TX=PA16 */
	pinmux_pin_set(muxa, 19, PINMUX_FUNC_C);
	pinmux_pin_set(muxa, 16, PINMUX_FUNC_C);
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(2, atmel_sam0_uart) && CONFIG_UART_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(3, atmel_sam0_uart) && CONFIG_UART_SAM0)
	/* SERCOM3 ON RX=PA23, TX=PA22 */
	pinmux_pin_set(muxa, 23, PINMUX_FUNC_C);
	pinmux_pin_set(muxa, 22, PINMUX_FUNC_C);
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(4, atmel_sam0_uart) && CONFIG_UART_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(5, atmel_sam0_uart) && CONFIG_UART_SAM0)
#warning Pin mapping may not be configured
#endif

#if (ATMEL_SAM0_DT_SERCOM_CHECK(0, atmel_sam0_spi) && CONFIG_SPI_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(1, atmel_sam0_spi) && CONFIG_SPI_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(2, atmel_sam0_spi) && CONFIG_SPI_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(3, atmel_sam0_spi) && CONFIG_SPI_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(4, atmel_sam0_spi) && CONFIG_SPI_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(5, atmel_sam0_spi) && CONFIG_SPI_SAM0)
	/* SPI SERCOM5 on MISO=PB16/pad 0, MOSI=PB22/pad 2, SCK=PB23/pad 3 */
	pinmux_pin_set(muxb, 16, PINMUX_FUNC_C);
	pinmux_pin_set(muxb, 22, PINMUX_FUNC_D);
	pinmux_pin_set(muxb, 23, PINMUX_FUNC_D);
#endif

#if (ATMEL_SAM0_DT_SERCOM_CHECK(0, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(1, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(2, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
	/* SERCOM2 on SDA=PA08, SCL=PA09 */
	pinmux_pin_set(muxa, 8, PINMUX_FUNC_D);
	pinmux_pin_set(muxa, 9, PINMUX_FUNC_D);
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(3, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(4, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
#warning Pin mapping may not be configured
#endif
#if (ATMEL_SAM0_DT_SERCOM_CHECK(5, atmel_sam0_i2c) && CONFIG_I2C_SAM0)
#warning Pin mapping may not be configured
#endif

#ifdef CONFIG_USB_DC_SAM0
	/* USB DP on PA25, USB DM on PA24 */
	pinmux_pin_set(muxa, 25, PINMUX_FUNC_G);
	pinmux_pin_set(muxa, 24, PINMUX_FUNC_G);
#endif
	return 0;
}

SYS_INIT(board_pinmux_init, PRE_KERNEL_1, CONFIG_PINMUX_INIT_PRIORITY);