Boot Linux faster!

Check our new training course

Boot Linux faster!

Check our new training course
and Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

/*
 * Copyright (c) 2017 I-SENSE group of ICCS
 * Copyright (c) 2019 Centaur Analytics, Inc
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <arm/armv7-m.dtsi>
#include <dt-bindings/clock/stm32_clock.h>
#include <dt-bindings/i2c/i2c.h>
#include <dt-bindings/gpio/gpio.h>

/ {
	chosen {
		zephyr,flash-controller = &flash;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-m4f";
			reg = <0>;
		};
	};

	sram0: memory@20000000 {
		compatible = "mmio-sram";
	};

	soc {
		flash: flash-controller@40022000 {
			compatible = "st,stm32-flash-controller", "st,stm32f3-flash-controller";
			label = "FLASH_CTRL";
			reg = <0x40022000 0x400>;
			interrupts = <4 0>;

			#address-cells = <1>;
			#size-cells = <1>;

			flash0: flash@8000000 {
				compatible = "soc-nv-flash";
				label = "FLASH_STM32";

				write-block-size = <2>;
				erase-block-size = <2048>;
			};
		};

		rcc: rcc@40021000 {
			compatible = "st,stm32-rcc";
			#clock-cells = <2>;
			reg = <0x40021000 0x400>;
			label = "STM32_CLK_RCC";
		};

		pinctrl: pin-controller@48000000 {
			compatible = "st,stm32-pinmux";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0x48000000 0x1800>;

			gpioa: gpio@48000000 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000000 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x00020000>;
				label = "GPIOA";
			};

			gpiob: gpio@48000400 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000400 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x00040000>;
				label = "GPIOB";
			};

			gpioc: gpio@48000800 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000800 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x00080000>;
				label = "GPIOC";
			};

			gpiod: gpio@48000c00 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000c00 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x00100000>;
				label = "GPIOD";
			};

			gpiof: gpio@48001400 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48001400 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x00400000>;
				label = "GPIOF";
			};
		};

		iwdg: watchdog@40003000 {
			compatible = "st,stm32-watchdog";
			reg = <0x40003000 0x400>;
			label = "IWDG";
			status = "disabled";
		};

		wwdg: watchdog@40002c00 {
			compatible = "st,stm32-window-watchdog";
			reg = <0x40002C00 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000800>;
			label = "WWDG";
			interrupts = <0 7>;
			status = "disabled";
		};

		usart1: serial@40013800 {
			compatible = "st,stm32-usart", "st,stm32-uart";
			reg = <0x40013800 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00004000>;
			interrupts = <37 0>;
			status = "disabled";
			label = "UART_1";
		};

		usart2: serial@40004400 {
			compatible = "st,stm32-usart", "st,stm32-uart";
			reg = <0x40004400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00020000>;
			interrupts = <38 0>;
			status = "disabled";
			label = "UART_2";
		};

		usart3: serial@40004800 {
			compatible = "st,stm32-usart", "st,stm32-uart";
			reg = <0x40004800 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00040000>;
			interrupts = <39 0>;
			status = "disabled";
			label = "UART_3";
		};

		i2c1: i2c@40005400 {
			compatible = "st,stm32-i2c-v2";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40005400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00200000>;
			interrupts = <31 0>, <32 0>;
			interrupt-names = "event", "error";
			status = "disabled";
			label= "I2C_1";
		};

		spi1: spi@40013000 {
			compatible = "st,stm32-spi-fifo", "st,stm32-spi";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40013000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00001000>;
			interrupts = <35 5>;
			status = "disabled";
			label = "SPI_1";
		};

		usb: usb@40005c00 {
			compatible = "st,stm32-usb";
			reg = <0x40005c00 0x400>;
			interrupts = <20 0>;
			interrupt-names = "usb";
			num-bidir-endpoints = <8>;
			ram-size = <512>;
			phys = <&usb_fs_phy>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00800000>;
			status = "disabled";
			label= "USB";
		};

		timers2: timers@40000000 {
			compatible = "st,stm32-timers";
			reg = <0x40000000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000001>;
			status = "disabled";
			label = "TIMERS_2";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <0>;
				label = "PWM_2";
				#pwm-cells = <2>;
			};
		};

		timers3: timers@40000400 {
			compatible = "st,stm32-timers";
			reg = <0x40000400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000002>;
			status = "disabled";
			label = "TIMERS_3";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_3";
				#pwm-cells = <2>;
			};
		};

		timers6: timers@40001000 {
			compatible = "st,stm32-timers";
			reg = <0x40001000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000010>;
			status = "disabled";
			label = "TIMERS_6";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_6";
				#pwm-cells = <2>;
			};
		};

		timers7: timers@40001400 {
			compatible = "st,stm32-timers";
			reg = <0x40001400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000020>;
			status = "disabled";
			label = "TIMERS_7";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_7";
				#pwm-cells = <2>;
			};
		};

		timers15: timers@40014000 {
			compatible = "st,stm32-timers";
			reg = <0x40014000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00010000>;
			status = "disabled";
			label = "TIMERS_15";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_15";
				#pwm-cells = <2>;
			};
		};

		timers16: timers@40014400 {
			compatible = "st,stm32-timers";
			reg = <0x40014400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00020000>;
			status = "disabled";
			label = "TIMERS_16";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_16";
				#pwm-cells = <2>;
			};
		};

		timers17: timers@40014800 {
			compatible = "st,stm32-timers";
			reg = <0x40014800 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00040000>;
			status = "disabled";
			label = "TIMERS_17";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_17";
				#pwm-cells = <2>;
			};
		};

		rtc: rtc@40002800 {
			compatible = "st,stm32-rtc";
			reg = <0x40002800 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>;
			interrupts = <41 0>;
			prescaler = <32768>;
			status = "disabled";
			label = "RTC_0";
		};

		can1: can@40006400 {
			compatible = "st,stm32-can";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40006400 0x400>;
			interrupts = <19 0>, <20 0>, <21 0>, <22 0>;
			interrupt-names = "TX", "RX0", "RX1", "SCE";
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x02000000>;
			status = "disabled";
			label = "CAN_1";
			bus-speed = <125000>;
			sjw = <1>;
			prop-seg = <0>;
			phase-seg1 = <5>;
			phase-seg2 = <6>;
		};

		adc1: adc@50000000 {
			compatible = "st,stm32-adc";
			reg = <0x50000000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x10000000>;
			interrupts = <18 0>;
			status = "disabled";
			label = "ADC_1";
			#io-channel-cells = <1>;
		};

		dma1: dma@40020000 {
			compatible = "st,stm32-dma";
			#dma-cells = <4>;
			reg = <0x40020000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x1>;
			interrupts = <11 0 12 0 13 0 14 0 15 0 16 0 17 0>;
			status = "disabled";
			label = "DMA_1";
		};
	};

	usb_fs_phy: usbphy {
		compatible = "usb-nop-xceiv";
		#phy-cells = <0>;
		label = "USB_FS_PHY";
	};
};

&nvic {
	arm,num-irq-priority-bits = <4>;
};