Boot Linux faster!

Check our new training course

Boot Linux faster!

Check our new training course
and Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

/*
 * Copyright (c) 2018 Henrik Brix Andersen <henrik@brixandersen.dk>
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <init.h>
#include <drivers/pinmux.h>

static int board_pinmux_init(struct device *dev)
{
	struct device *muxa = device_get_binding(DT_ATMEL_SAM0_PINMUX_PINMUX_A_LABEL);
#if DT_ATMEL_SAM0_SPI_SERCOM_4_BASE_ADDRESS
	struct device *muxb = device_get_binding(DT_ATMEL_SAM0_PINMUX_PINMUX_B_LABEL);
#endif
	ARG_UNUSED(dev);

#if DT_ATMEL_SAM0_UART_SERCOM_0_BASE_ADDRESS
	/* SERCOM0 on RX=PA11/pad 3, TX=PA10/pad 2 */
	pinmux_pin_set(muxa, 11, PINMUX_FUNC_C);
	pinmux_pin_set(muxa, 10, PINMUX_FUNC_C);
#endif

#if DT_ATMEL_SAM0_UART_SERCOM_1_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_UART_SERCOM_2_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_UART_SERCOM_3_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_UART_SERCOM_4_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_UART_SERCOM_5_BASE_ADDRESS
#error Pin mapping is not configured
#endif

#if DT_ATMEL_SAM0_SPI_SERCOM_4_BASE_ADDRESS
	/* SPI SERCOM4 on MISO=PA12/pad 0, MOSI=PB10/pad 2, SCK=PB11/pad 3 */
	pinmux_pin_set(muxa, 12, PINMUX_FUNC_D);
	pinmux_pin_set(muxb, 10, PINMUX_FUNC_D);
	pinmux_pin_set(muxb, 11, PINMUX_FUNC_D);
#endif

#if DT_ATMEL_SAM0_SPI_SERCOM_0_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_SPI_SERCOM_1_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_SPI_SERCOM_2_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_SPI_SERCOM_3_BASE_ADDRESS
#error Pin mapping is not configured
#endif
#if DT_ATMEL_SAM0_SPI_SERCOM_5_BASE_ADDRESS
#error Pin mapping is not configured
#endif

#ifdef CONFIG_USB_DC_SAM0
	/* USB DP on PA25, USB DM on PA24 */
	pinmux_pin_set(muxa, 25, PINMUX_FUNC_G);
	pinmux_pin_set(muxa, 24, PINMUX_FUNC_G);
#endif

	return 0;
}

SYS_INIT(board_pinmux_init, PRE_KERNEL_1, CONFIG_PINMUX_INIT_PRIORITY);