Linux preempt-rt

Check our new training course

Real-Time Linux with PREEMPT_RT

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

# Kconfig - STM32 MCU clock control driver config
#
# Copyright (c) 2017 Linaro
#
#  SPDX-License-Identifier: Apache-2.0
#

if SOC_FAMILY_STM32

menuconfig CLOCK_CONTROL_STM32_CUBE
	bool
	prompt "STM32 Reset & Clock Control"
	depends on CLOCK_CONTROL
	default n if SOC_SERIES_STM32
	help
	  Enable driver for Reset & Clock Control subsystem found
	  in STM32 family of MCUs

config CLOCK_CONTROL_STM32_DEVICE_INIT_PRIORITY
	int "Clock Control Device Priority"
	default 1
	depends on CLOCK_CONTROL_STM32_CUBE
	help
	  This option controls the priority of clock control
	  device initialization. Higher priority ensures that the device
	  is initialized earlier in the startup cycle. If unsure, leave
	  at default value 1

choice
prompt "STM32 System Clock Source"
depends on CLOCK_CONTROL_STM32_CUBE
default CLOCK_STM32_SYSCLK_SRC_PLL

config CLOCK_STM32_SYSCLK_SRC_HSE
	bool "HSE"
	help
	  Use HSE as source of SYSCLK

config CLOCK_STM32_SYSCLK_SRC_HSI
	bool "HSI"
	help
	  Use HSI as source of SYSCLK

config CLOCK_STM32_SYSCLK_SRC_PLL
	bool "PLL"
	help
	  Use PLL as source of SYSCLK

endchoice

config CLOCK_STM32_HSE_BYPASS
	bool "HSE bypass"
	depends on CLOCK_CONTROL_STM32_CUBE && (CLOCK_STM32_SYSCLK_SRC_HSE || CLOCK_STM32_PLL_SRC_HSE)
	help
	  Enable this option to bypass external high-speed clock (HSE).

config CLOCK_STM32_HSE_CLOCK
	int "HSE clock value"
	depends on CLOCK_CONTROL_STM32_CUBE && (CLOCK_STM32_SYSCLK_SRC_HSE || CLOCK_STM32_PLL_SRC_HSE)
	help
	  Value of external high-speed clock (HSE).

choice
prompt "STM32 PLL Clock Source"
depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
default CLOCK_STM32_PLL_SRC_HSI

config CLOCK_STM32_PLL_SRC_MSI
	bool "MSI"
	help
	  Use MSI as source of PLL

config CLOCK_STM32_PLL_SRC_HSI
	bool "HSI"
	help
	  Use HSI as source of PLL

config CLOCK_STM32_PLL_SRC_HSE
	bool "HSE"
	help
	  Use HSE as source of PLL
endchoice

if SOC_SERIES_STM32F3X

config CLOCK_STM32_PLL_PREDIV
	int "PREDIV Prescaler"
	depends on CLOCK_CONTROL_STM32_CUBE
	default 1
	range 1 16
	help
	 PREDIV is PLLSCR clock signal prescaler, allowed values: 1 - 16.

config CLOCK_STM32_PLL_PREDIV1
	int "PREDIV1 Prescaler"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_PLL_SRC_HSE && (SOC_STM32F302XE || SOC_STM32F303XE || SOC_STM32F398XX)
	default 1
	range 1 16
	help
	 PREDIV is PLLSCR clock signal prescaler, present on STM32F302xE, STM32F303xE and STM32F39xx SoCs.
	 Allowed values: 1 - 16.

config CLOCK_STM32_PLL_MULTIPLIER
	int "PLL multiplier"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 9
	range 2 16
	help
	 PLL multiplier, allowed values: 2-16. PLL output must not exceed 72MHz.

endif # SOC_SERIES_STM32F3X

if SOC_SERIES_STM32F4X

config CLOCK_STM32_PLL_M_DIVISOR
	int "Division factor for PLL VCO input clock"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 8
	range 2 63
	help
	 PLLM division factor needs to be set correctly to ensure that the VCO
	 input frequency ranges from 1 to 2 MHz. It is recommended to select a
	 frequency of 2 MHz to limit PLL jitter.
	 Allowed values: 2-63

config CLOCK_STM32_PLL_N_MULTIPLIER
	int "Multiplier factor for PLL VCO output clock"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 336
	range 192 432 if SOC_STM32F401XE
	range 50 432
	help
	 PLLN multiplier factor needs to be set correctly to ensure that the
	 VCO output frequency is between 100 and 432 MHz, except on STM32F401
	 where the frequency must be between 192 and 432 MHz.
	 Allowed values: 50-432 (STM32F401: 192-432)

config CLOCK_STM32_PLL_P_DIVISOR
	int "PLL division factor for main system clock"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 4
	range 2 8
	help
	 PLLP division factor needs to be set correctly to not exceed 84MHz.
	 Allowed values: 2, 4, 6, 8

config CLOCK_STM32_PLL_Q_DIVISOR
	int "Division factor for OTG FS, SDIO and RNG clocks"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 7
	range 2 15
	help
	 The USB OTG FS requires a 48MHz clock to work correctly. SDIO and RNG
	 need a frequency lower than or equal to 48 MHz to work correctly.
	 Allowed values: 2-15

endif # SOC_SERIES_STM32F4X

if SOC_SERIES_STM32L4X

config CLOCK_STM32_PLL_M_DIVISOR
	int "PLL divisor"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 1
	range 1 8
	help
	  PLL divisor, allowed values: 1-8. With this ensure that the PLL
	  VCO input frequency ranges from 4 to 16MHz.

config CLOCK_STM32_PLL_N_MULTIPLIER
	int "PLL multiplier"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 20
	range 8 86
	help
	  PLL multiplier, allowed values: 2-16. PLL output must not
	  exceed 344MHz.

config CLOCK_STM32_PLL_P_DIVISOR
	int "PLL P Divisor"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 7
	range 0 17
	help
	  PLL P Output divisor, allowed values: 0, 7, 17.

config CLOCK_STM32_PLL_Q_DIVISOR
	int "PLL Q Divisor"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 2
	range 0 8
	help
	  PLL Q Output divisor, allowed values: 0, 2, 4, 6, 8.

config CLOCK_STM32_PLL_R_DIVISOR
	int "PLL R Divisor"
	depends on CLOCK_CONTROL_STM32_CUBE && CLOCK_STM32_SYSCLK_SRC_PLL
	default 4
	range 0 8
	help
	  PLL R Output divisor, allowed values: 0, 2, 4, 6, 8.

endif # SOC_SERIES_STM32L4X

config CLOCK_STM32_AHB_PRESCALER
	int "AHB prescaler"
	depends on CLOCK_CONTROL_STM32_CUBE
	default 0
	range 0 512
	help
	  AHB prescaler, allowed values: 1, 2, 4, 8, 16, 64, 128,
	  256, 512.

config CLOCK_STM32_APB1_PRESCALER
	int "APB1 prescaler"
	depends on CLOCK_CONTROL_STM32_CUBE
	default 1
	range 1 16
	help
	  APB1 Low speed clock (PCLK1) prescaler, allowed values:
	  1, 2, 4, 8, 16

config CLOCK_STM32_APB2_PRESCALER
	int "APB2 prescaler"
	depends on CLOCK_CONTROL_STM32_CUBE
	default 1
	range 1 16
	help
	  APB2 High speed clock (PCLK2) prescaler, allowed values:
	  1, 2, 4, 8, 16

endif # SOC_FAMILY_STM32