Linux debugging

Check our new training course

Linux debugging, tracing, profiling & perf. analysis

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

Open Menu /drivers/sensor/mcp9808/Kconfig 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
# Kconfig - MCP9808 temperature sensor configuration options

#
# Copyright (c) 2016 Intel Corporation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#

menuconfig MCP9808
	bool "MCP9808 temperature sensor"
	depends on SENSOR && I2C
	default n
	help
	 Enable driver for MCP9808 temperature sensor.

config MCP9808_DEV_NAME
	string "MCP9808 device name"
	depends on MCP9808
	default "MCP9808"


config MCP9808_I2C_ADDR
	hex "MCP9808 I2C slave address"
	depends on MCP9808
	default 0x18
	help
	 Specify the I2C slave address for the MCP9808.

config MCP9808_I2C_DEV_NAME
	string "I2C master where MCP9808 is connected"
	depends on MCP9808
	default "I2C_0"
	help
	 Specify the device name of the I2C master device to which MCP9808 is
	 connected.

choice
	prompt "MCP9808 trigger mode"
	depends on MCP9808
	default MCP9808_TRIGGER_NONE

config MCP9808_TRIGGER_NONE
	bool "No trigger"

config MCP9808_TRIGGER_GLOBAL_THREAD
	depends on GPIO
	select MCP9808_TRIGGER
	bool "Use global thread"

config MCP9808_TRIGGER_OWN_THREAD
	depends on GPIO
	select MCP9808_TRIGGER
	bool "Use own thread"

endchoice

config MCP9808_TRIGGER
	bool
	depends on MCP9808

config MCP9808_GPIO_CONTROLLER
	string "GPIO controller for MCP9808 interrupt"
	depends on MCP9808 && MCP9808_TRIGGER
	default "GPIO_0"
	help
	  The GPIO controller the MCP9808 interrupt is connected to.

config MCP9808_GPIO_PIN
	int "GPIO pin for MCP9808 interrupt"
	depends on MCP9808 && MCP9808_TRIGGER
	default 3
	help
	  The GPIO pin the MCP9808 interrupt is connected to.

config MCP9808_THREAD_STACK_SIZE
	int "Sensor delayed work thread stack size"
	depends on MCP9808 && MCP9808_TRIGGER_OWN_THREAD
	default 1024

config MCP9808_THREAD_PRIORITY
	int "MCP9808 thread priority"
	depends on MCP9808 && MCP9808_TRIGGER_OWN_THREAD
	default 10