Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 | # Kconfig.mcp9808 - MCP9808 temperature sensor configuration options # # Copyright (c) 2016 Intel Corporation # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # menuconfig MCP9808 bool "MCP9808 temperature sensor" depends on SENSOR && I2C default n help Enable driver for MCP9808 temperature sensor. config MCP9808_SYS_LOG_LEVEL int "MCP9808 Log level" depends on SYS_LOG && MCP9808 default 0 range 0 4 help Sets log level for MCP9808 driver. Levels are: - 0 OFF: do not write - 1 ERROR: only write SYS_LOG_ERR - 2 WARNING: write SYS_LOG_WRN in addition to previous level - 3 INFO: write SYS_LOG_INF in addition to previous levels - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels config MCP9808_DEV_NAME string "MCP9808 device name" depends on MCP9808 default "MCP9808" config MCP9808_INIT_PRIORITY int depends on MCP9808 default 70 prompt "Init priority" help Device driver initialization priority. config MCP9808_I2C_ADDR hex "MCP9808 I2C slave address" depends on MCP9808 default 0x18 help Specify the I2C slave address for the MCP9808. config MCP9808_I2C_DEV_NAME string "I2C master where MCP9808 is connected" depends on MCP9808 default "I2C_0" help Specify the device name of the I2C master device to which MCP9808 is connected. choice prompt "MCP9808 trigger mode" depends on MCP9808 default MCP9808_TRIGGER_NONE config MCP9808_TRIGGER_NONE bool "No trigger" config MCP9808_TRIGGER_GLOBAL_FIBER depends on GPIO && SYSTEM_WORKQUEUE select MCP9808_TRIGGER bool "Use global fiber" config MCP9808_TRIGGER_OWN_FIBER depends on GPIO select MCP9808_TRIGGER bool "Use own fiber" endchoice config MCP9808_TRIGGER bool depends on MCP9808 config MCP9808_GPIO_CONTROLLER string "GPIO controller for MCP9808 interrupt" depends on MCP9808 && MCP9808_TRIGGER default "GPIO_0" help The GPIO controller the MCP9808 interrupt is connected to. config MCP9808_GPIO_PIN int "GPIO pin for MCP9808 interrupt" depends on MCP9808 && MCP9808_TRIGGER default 3 help The GPIO pin the MCP9808 interrupt is connected to. config MCP9808_FIBER_STACK_SIZE int "Sensor delayed work fiber stack size" depends on MCP9808 && MCP9808_TRIGGER_OWN_FIBER default 1024 config MCP9808_FIBER_PRIORITY int "MCP9808 fiber priority" depends on MCP9808 && MCP9808_TRIGGER_OWN_FIBER default 10 |