Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 | # Kconfig.hdc1008 - HDC1008 temperature and humidity sensor configuration options # # Copyright (c) 2016 Intel Corporation # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # menuconfig HDC1008 bool prompt "HDC1008 Temperature and Humidity Sensor" depends on SENSOR && I2C && GPIO default n help Enable driver for HDC1008 temperature and humidity sensors. config HDC1008_SYS_LOG_LEVEL int "HDC1008 Log level" depends on SYS_LOG && HDC1008 default 0 range 0 4 help Sets log level for HDC1008 driver. Levels are: - 0 OFF: do not write - 1 ERROR: only write SYS_LOG_ERR - 2 WARNING: write SYS_LOG_WRN in addition to previous level - 3 INFO: write SYS_LOG_INF in addition to previous levels - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels config HDC1008_NAME string prompt "Driver name" default "HDC1008" depends on HDC1008 help Device name with which the HDC1008 sensor is identified. config HDC1008_INIT_PRIORITY int prompt "Init priority" depends on HDC1008 default 70 help Device driver initialization priority. choice prompt "I2C address" depends on HDC1008 default HDC1008_I2C_ADDR_0 help I2C address of the HDC1008 sensor. config HDC1008_I2C_ADDR_0 bool prompt "0x40" help A0 connected GND and A1 connected to GND. config HDC1008_I2C_ADDR_1 bool prompt "0x41" help A0 connected VDD and A1 connected to GND. config HDC1008_I2C_ADDR_2 bool prompt "0x42" help A0 connected GND and A1 connected to VDD. config HDC1008_I2C_ADDR_3 bool prompt "0x43" help A0 connected VDD and A1 connected to VDD. endchoice config HDC1008_I2C_MASTER_DEV_NAME string prompt "I2C master where HDC1008 is connected" depends on HDC1008 default "I2C_0" help Specify the device name of the I2C master device to which the HDC1008 chip is connected. config HDC1008_GPIO_DEV_NAME string prompt "GPIO device" default "GPIO_0" depends on HDC1008 help The device name of the GPIO device to which the HDC1008 data-ready pin is connected. config HDC1008_GPIO_PIN_NUM int prompt "Interrupt GPIO pin number" default 0 depends on HDC1008 help The number of the GPIO on which the data-ready signal from the HDC1008 chip will be received. |