Linux Audio

Check our new training course

Embedded Linux Audio

Check our new training course
with Creative Commons CC-BY-SA
lecture materials

Bootlin logo

Elixir Cross Referencer

Loading...
  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
/*
 * Copyright (c) 2015 Intel Corporation.
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

/**
 * @file Driver for PCAL9535A I2C-based GPIO driver.
 */

#include <errno.h>

#include <nanokernel.h>

#include <misc/util.h>
#include <gpio.h>
#include <i2c.h>

#include "gpio_pcal9535a.h"

#ifndef CONFIG_GPIO_PCAL9535A_DEBUG
#define DBG(...) { ; }
#else
#if defined(CONFIG_STDOUT_CONSOLE)
#include <stdio.h>
#define DBG printf
#else
#include <misc/printk.h>
#define DBG printk
#endif /* CONFIG_STDOUT_CONSOLE */
#endif /* CONFIG_GPIO_PCAL9535A_DEBUG */

/* Register definitions */
#define REG_INPUT_PORT0			0x00
#define REG_INPUT_PORT1			0x01
#define REG_OUTPUT_PORT0		0x02
#define REG_OUTPUT_PORT1		0x03
#define REG_POL_INV_PORT0		0x04
#define REG_POL_INV_PORT1		0x05
#define REG_CONF_PORT0			0x06
#define REG_CONG_PORT1			0x07
#define REG_OUT_DRV_STRENGTH_PORT0_L	0x40
#define REG_OUT_DRV_STRENGTH_PORT0_H	0x41
#define REG_OUT_DRV_STRENGTH_PORT1_L	0x42
#define REG_OUT_DRV_STRENGTH_PORT1_H	0x43
#define REG_INPUT_LATCH_PORT0		0x44
#define REG_INPUT_LATCH_PORT1		0x45
#define REG_PUD_EN_PORT0		0x46
#define REG_PUD_EN_PORT1		0x47
#define REG_PUD_SEL_PORT0		0x48
#define REG_PUD_SEL_PORT1		0x49
#define REG_INT_MASK_PORT0		0x4A
#define REG_INT_MASK_PORT1		0x4B
#define REG_INT_STATUS_PORT0		0x4C
#define REG_INT_STATUS_PORT1		0x4D
#define REG_OUTPUT_PORT_CONF		0x4F

/**
 * @brief Check to see if a I2C master is identified for communication.
 *
 * @param dev Device struct.
 * @return 1 if I2C master is identified, 0 if not.
 */
static inline int _has_i2c_master(struct device *dev)
{
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	struct device * const i2c_master = drv_data->i2c_master;

	if (i2c_master)
		return 1;
	else
		return 0;
}

/**
 * @brief Read both port 0 and port 1 registers of certain register function.
 *
 * Given the register in reg, read the pair of port 0 and port 1.
 *
 * @param dev Device struct of the PCAL9535A.
 * @param reg Register to read (the PORT0 of the pair of registers).
 * @param buf Buffer to read data into.
 *
 * @return 0 if successful, failed otherwise.
 */
static int _read_port_regs(struct device *dev, uint8_t reg,
			   union gpio_pcal9535a_port_data *buf)
{
	const struct gpio_pcal9535a_config * const config =
		dev->config->config_info;
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	struct device * const i2c_master = drv_data->i2c_master;
	uint16_t i2c_addr = config->i2c_slave_addr;
	int ret;

	ret = i2c_burst_read(i2c_master, i2c_addr, reg, buf->byte, 2);
	if (ret) {
		DBG("PCAL9535A[0x%X]: error reading register 0x%X (%d)\n",
		    i2c_addr, reg, ret);
		goto error;
	}

	DBG("PCAL9535A[0x%X]: Read: REG[0x%X] = 0x%X, REG[0x%X] = 0x%X\n",
	    i2c_addr, reg, buf->byte[0], (reg + 1), buf->byte[1]);

error:
	return ret;
}

/**
 * @brief Write both port 0 and port 1 registers of certain register function.
 *
 * Given the register in reg, write the pair of port 0 and port 1.
 *
 * @param dev Device struct of the PCAL9535A.
 * @param reg Register to write into (the PORT0 of the pair of registers).
 * @param buf Buffer to write data from.
 *
 * @return 0 if successful, failed otherwise.
 */
static int _write_port_regs(struct device *dev, uint8_t reg,
			    union gpio_pcal9535a_port_data *buf)
{
	const struct gpio_pcal9535a_config * const config =
		dev->config->config_info;
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	struct device * const i2c_master = drv_data->i2c_master;
	uint16_t i2c_addr = config->i2c_slave_addr;
	int ret;

	DBG("PCAL9535A[0x%X]: Write: REG[0x%X] = 0x%X, REG[0x%X] = 0x%X\n",
	    i2c_addr, reg, buf->byte[0], (reg + 1), buf->byte[1]);

	ret = i2c_burst_write(i2c_master, i2c_addr, reg, buf->byte, 2);
	if (ret) {
		DBG("PCAL9535A[0x%X]: error writing from register 0x%X (%d)\n",
		    i2c_addr, reg, ret);
	}

	return ret;
}

/**
 * @brief Setup the pin direction (input or output)
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param flags Flags of pin or port
 *
 * @return 0 if successful, failed otherwise
 */
static int _setup_pin_dir(struct device *dev, int access_op,
			  uint32_t pin, int flags)
{
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	union gpio_pcal9535a_port_data *port = &drv_data->reg_cache.dir;
	uint16_t bit_mask;
	uint16_t new_value = 0;
	int ret;

	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		bit_mask = 1 << pin;

		/* Config 0 == output, 1 == input */
		if ((flags & GPIO_DIR_MASK) == GPIO_DIR_IN) {
			new_value = 1 << pin;
		}

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	case GPIO_ACCESS_BY_PORT:
		/* Config 0 == output, 1 == input */
		if ((flags & GPIO_DIR_MASK) == GPIO_DIR_IN) {
			port->all = 0xFFFF;
		} else {
			port->all = 0x0;
		}
		break;
	default:
		ret = -ENOTSUP;
		goto done;
	}

	ret = _write_port_regs(dev, REG_CONF_PORT0, port);

done:
	return ret;
}

/**
 * @brief Setup the pin pull up/pull down status
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param flags Flags of pin or port
 *
 * @return 0 if successful, failed otherwise
 */
static int _setup_pin_pullupdown(struct device *dev, int access_op,
				 uint32_t pin, int flags)
{
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	union gpio_pcal9535a_port_data *port;
	uint16_t bit_mask;
	uint16_t new_value = 0;
	int ret;

	/* If disabling pull up/down, there is no need to set the selection
	 * register. Just go straight to disabling.
	 */
	if ((flags & GPIO_PUD_MASK) == GPIO_PUD_NORMAL) {
		goto en_dis;
	}

	/* Setup pin pull up or pull down */
	port = &drv_data->reg_cache.pud_sel;
	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		bit_mask = 1 << pin;

		/* pull down == 0, pull up == 1*/
		if ((flags & GPIO_PUD_MASK) == GPIO_PUD_PULL_UP) {
			new_value = 1 << pin;
		}

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	case GPIO_ACCESS_BY_PORT:
		/* pull down == 0, pull up == 1*/
		if ((flags & GPIO_PUD_MASK) == GPIO_PUD_PULL_UP) {
			port->all = 0xFFFF;
		} else {
			port->all = 0x0;
		}
		break;
	default:
		ret = -ENOTSUP;
		goto done;
	}

	ret = _write_port_regs(dev, REG_PUD_SEL_PORT0, port);
	if (ret) {
		goto done;
	}

en_dis:
	/* enable/disable pull up/down */
	port = &drv_data->reg_cache.pud_en;
	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		bit_mask = 1 << pin;

		if ((flags & GPIO_PUD_MASK) != GPIO_PUD_NORMAL) {
			new_value = 1 << pin;
		}

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	case GPIO_ACCESS_BY_PORT:
		if ((flags & GPIO_PUD_MASK) != GPIO_PUD_NORMAL) {
			port->all = 0xFFFF;
		} else {
			port->all = 0x0;
		}
		break;
	default:
		ret = -ENOTSUP;
		goto done;
	}

	ret = _write_port_regs(dev, REG_PUD_EN_PORT0, port);

done:
	return ret;
}

/**
 * @brief Setup the polarity of pin or port
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param flags Flags of pin or port
 *
 * @return 0 if successful, failed otherwise
 */
static int _setup_pin_polarity(struct device *dev, int access_op,
			       uint32_t pin, int flags)
{
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	union gpio_pcal9535a_port_data *port = &drv_data->reg_cache.pol_inv;
	uint16_t bit_mask;
	uint16_t new_value = 0;
	int ret;

	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		bit_mask = BIT(pin);

		/* normal == 0, invert == 1 */
		if ((flags & GPIO_POL_MASK) == GPIO_POL_INV) {
			new_value = BIT(pin);
		}

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	case GPIO_ACCESS_BY_PORT:
		/* normal == 0, invert == 1 */
		if ((flags & GPIO_POL_MASK) == GPIO_POL_INV) {
			port->all = 0xFFFF;
		} else {
			port->all = 0x0;
		}
		break;
	default:
		ret = -ENOTSUP;
		goto done;
	}

	ret = _write_port_regs(dev, REG_POL_INV_PORT0, port);
	if (!ret) {
		drv_data->out_pol_inv = port->all;
	}

done:
	return ret;
}

/**
 * @brief Configurate pin or port
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param flags Flags of pin or port
 *
 * @return 0 if successful, failed otherwise
 */
static int gpio_pcal9535a_config(struct device *dev, int access_op,
				 uint32_t pin, int flags)
{
	int ret;

#ifdef CONFIG_GPIO_PCAL9535A_DEBUG
	const struct gpio_pcal9535a_config * const config =
		dev->config->config_info;
	uint16_t i2c_addr = config->i2c_slave_addr;
#endif

	if (!_has_i2c_master(dev)) {
		return -EINVAL;
	}

	ret = _setup_pin_dir(dev, access_op, pin, flags);
	if (ret) {
		DBG("PCAL9535A[0x%X]: error setting pin direction (%d)\n",
		    i2c_addr, ret);
		goto done;
	}

	ret = _setup_pin_polarity(dev, access_op, pin, flags);
	if (ret) {
		DBG("PCAL9535A[0x%X]: error setting pin polarity (%d)\n",
		    i2c_addr, ret);
		goto done;
	}

	ret = _setup_pin_pullupdown(dev, access_op, pin, flags);
	if (ret) {
		DBG("PCAL9535A[0x%X]: error setting pin pull up/down (%d)\n",
		    i2c_addr, ret);
		goto done;
	}

done:
	return ret;
}

/**
 * @brief Set the pin or port output
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param value Value to set (0 or 1)
 *
 * @return 0 if successful, failed otherwise
 */
static int gpio_pcal9535a_write(struct device *dev, int access_op,
				uint32_t pin, uint32_t value)
{
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	union gpio_pcal9535a_port_data *port = &drv_data->reg_cache.output;
	uint16_t bit_mask;
	uint16_t new_value;
	int ret;

	if (!_has_i2c_master(dev)) {
		return -EINVAL;
	}

	/* Invert input value for pins configurated as active low. */
	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		bit_mask = BIT(pin);

		new_value = (value << pin) & bit_mask;
		new_value ^= (drv_data->out_pol_inv & bit_mask);
		new_value &= bit_mask;

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	case GPIO_ACCESS_BY_PORT:
		port->all = value;
		bit_mask = drv_data->out_pol_inv;

		new_value = value & bit_mask;
		new_value ^= drv_data->out_pol_inv;
		new_value &= bit_mask;

		port->all &= ~bit_mask;
		port->all |= new_value;

		break;
	default:
		ret = -ENOTSUP;
		goto done;
	}

	ret = _write_port_regs(dev, REG_OUTPUT_PORT0, port);

done:
	return ret;
}

/**
 * @brief Read the pin or port status
 *
 * @param dev Device struct of the PCAL9535A
 * @param access_op Access operation (pin or port)
 * @param pin The pin number
 * @param value Value of input pin(s)
 *
 * @return 0 if successful, failed otherwise
 */
static int gpio_pcal9535a_read(struct device *dev, int access_op,
			       uint32_t pin, uint32_t *value)
{
	union gpio_pcal9535a_port_data buf;
	int ret;

	if (!_has_i2c_master(dev)) {
		return -EINVAL;
	}

	ret = _read_port_regs(dev, REG_INPUT_PORT0, &buf);
	if (ret != 0) {
		goto done;
	}

	switch (access_op) {
	case GPIO_ACCESS_BY_PIN:
		*value = (buf.all >> pin) & 0x01;
		break;
	case GPIO_ACCESS_BY_PORT:
		*value = buf.all;
		break;
	default:
		ret = -ENOTSUP;
		break;
	}

done:
	return ret;
}

static int gpio_pcal9535a_manage_callback(struct device *dev,
					  struct gpio_callback *callback,
					  bool set)
{
	ARG_UNUSED(dev);
	ARG_UNUSED(callback);
	ARG_UNUSED(set);

	return -ENOTSUP;
}

static int gpio_pcal9535a_enable_callback(struct device *dev,
					  int access_op, uint32_t pin)
{
	ARG_UNUSED(dev);
	ARG_UNUSED(access_op);
	ARG_UNUSED(pin);

	return -ENOTSUP;
}

static int gpio_pcal9535a_disable_callback(struct device *dev,
					   int access_op, uint32_t pin)
{
	ARG_UNUSED(dev);
	ARG_UNUSED(access_op);
	ARG_UNUSED(pin);

	return -ENOTSUP;
}

static struct gpio_driver_api gpio_pcal9535a_drv_api_funcs = {
	.config = gpio_pcal9535a_config,
	.write = gpio_pcal9535a_write,
	.read = gpio_pcal9535a_read,
	.manage_callback = gpio_pcal9535a_manage_callback,
	.enable_callback = gpio_pcal9535a_enable_callback,
	.disable_callback = gpio_pcal9535a_disable_callback,
};

/**
 * @brief Initialization function of PCAL9535A
 *
 * @param dev Device struct
 * @return 0 if successful, failed otherwise.
 */
int gpio_pcal9535a_init(struct device *dev)
{
	const struct gpio_pcal9535a_config * const config =
		dev->config->config_info;
	struct gpio_pcal9535a_drv_data * const drv_data =
		(struct gpio_pcal9535a_drv_data * const)dev->driver_data;
	struct device *i2c_master;

	/* Find out the device struct of the I2C master */
	i2c_master = device_get_binding((char *)config->i2c_master_dev_name);
	if (!i2c_master) {
		return -EINVAL;
	}
	drv_data->i2c_master = i2c_master;

	nano_timer_init(&drv_data->timer, (void *) 0);

	dev->driver_api = &gpio_pcal9535a_drv_api_funcs;

	return 0;
}

/* Initialization for PCAL9535A_0 */
#ifdef CONFIG_GPIO_PCAL9535A_0
#include <device.h>
#include <init.h>

static struct gpio_pcal9535a_config gpio_pcal9535a_0_cfg = {
	.i2c_master_dev_name = CONFIG_GPIO_PCAL9535A_0_I2C_MASTER_DEV_NAME,
	.i2c_slave_addr = CONFIG_GPIO_PCAL9535A_0_I2C_ADDR,
};

static struct gpio_pcal9535a_drv_data gpio_pcal9535a_0_drvdata = {
	/* Default for registers according to datasheet */
	.reg_cache.output = { .all = 0xFFFF },
	.reg_cache.pol_inv = { .all = 0x0 },
	.reg_cache.dir = { .all = 0xFFFF },
	.reg_cache.pud_en = { .all = 0x0 },
	.reg_cache.pud_sel = { .all = 0xFFFF },
};

/* This has to init after I2C master */
DEVICE_INIT(gpio_pcal9535a_0, CONFIG_GPIO_PCAL9535A_0_DEV_NAME,
	    gpio_pcal9535a_init,
	    &gpio_pcal9535a_0_drvdata, &gpio_pcal9535a_0_cfg,
	    SECONDARY, CONFIG_GPIO_PCAL9535A_INIT_PRIORITY);

#endif /* CONFIG_GPIO_PCAL9535A_0 */

/* Initialization for PCAL9535A_1 */
#ifdef CONFIG_GPIO_PCAL9535A_1
#include <device.h>
#include <init.h>

static struct gpio_pcal9535a_config gpio_pcal9535a_1_cfg = {
	.i2c_master_dev_name = CONFIG_GPIO_PCAL9535A_1_I2C_MASTER_DEV_NAME,
	.i2c_slave_addr = CONFIG_GPIO_PCAL9535A_1_I2C_ADDR,
};

static struct gpio_pcal9535a_drv_data gpio_pcal9535a_1_drvdata = {
	/* Default for registers according to datasheet */
	.reg_cache.output = { .all = 0xFFFF },
	.reg_cache.pol_inv = { .all = 0x0 },
	.reg_cache.dir = { .all = 0xFFFF },
	.reg_cache.pud_en = { .all = 0x0 },
	.reg_cache.pud_sel = { .all = 0xFFFF },
};

/* This has to init after I2C master */
DEVICE_INIT(gpio_pcal9535a_1, CONFIG_GPIO_PCAL9535A_1_DEV_NAME,
	    gpio_pcal9535a_init,
	    &gpio_pcal9535a_1_drvdata, &gpio_pcal9535a_1_cfg,
	    SECONDARY, CONFIG_GPIO_PCAL9535A_INIT_PRIORITY);

#endif /* CONFIG_GPIO_PCAL9535A_1 */

/* Initialization for PCAL9535A_2 */
#ifdef CONFIG_GPIO_PCAL9535A_2
#include <device.h>
#include <init.h>

static struct gpio_pcal9535a_config gpio_pcal9535a_2_cfg = {
	.i2c_master_dev_name = CONFIG_GPIO_PCAL9535A_2_I2C_MASTER_DEV_NAME,
	.i2c_slave_addr = CONFIG_GPIO_PCAL9535A_2_I2C_ADDR,
};

static struct gpio_pcal9535a_drv_data gpio_pcal9535a_2_drvdata = {
	/* Default for registers according to datasheet */
	.reg_cache.output = { .all = 0xFFFF },
	.reg_cache.pol_inv = { .all = 0x0 },
	.reg_cache.dir = { .all = 0xFFFF },
	.reg_cache.pud_en = { .all = 0x0 },
	.reg_cache.pud_sel = { .all = 0xFFFF },
};

/* This has to init after I2C master */
DEVICE_INIT(gpio_pcal9535a_2, CONFIG_GPIO_PCAL9535A_2_DEV_NAME,
	    gpio_pcal9535a_init,
	    &gpio_pcal9535a_2_drvdata, &gpio_pcal9535a_2_cfg,
	    SECONDARY, CONFIG_GPIO_PCAL9535A_INIT_PRIORITY);

#endif /* CONFIG_GPIO_PCAL9535A_2 */

/* Initialization for PCAL9535A_3 */
#ifdef CONFIG_GPIO_PCAL9535A_3
#include <device.h>
#include <init.h>

static struct gpio_pcal9535a_config gpio_pcal9535a_3_cfg = {
	.i2c_master_dev_name = CONFIG_GPIO_PCAL9535A_3_I2C_MASTER_DEV_NAME,
	.i2c_slave_addr = CONFIG_GPIO_PCAL9535A_3_I2C_ADDR,
};

static struct gpio_pcal9535a_drv_data gpio_pcal9535a_3_drvdata = {
	/* Default for registers according to datasheet */
	.reg_cache.output = { .all = 0xFFFF },
	.reg_cache.pol_inv = { .all = 0x0 },
	.reg_cache.dir = { .all = 0xFFFF },
	.reg_cache.pud_en = { .all = 0x0 },
	.reg_cache.pud_sel = { .all = 0xFFFF },
};

/* This has to init after I2C master */
DEVICE_INIT(gpio_pcal9535a_3, CONFIG_GPIO_PCAL9535A_3_DEV_NAME,
	    gpio_pcal9535a_init,
	    &gpio_pcal9535a_3_drvdata, &gpio_pcal9535a_3_cfg,
	    SECONDARY, CONFIG_GPIO_PCAL9535A_INIT_PRIORITY);

#endif /* CONFIG_GPIO_PCAL9535A_3 */