1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 | # Kconfig.sx9500 - SX9500 SAR proximity sensor configuration options
#
# Copyright (c) 2016 Intel Corporation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#
menuconfig SX9500
bool "SX9500 I2C SAR Proximity Chip"
depends on SENSOR && I2C
default n
help
Enable driver for SX9500 I2C-based SAR proximity sensor.
config SX9500_DEV_NAME
string "SX9500 device name"
depends on SX9500
default "SX9500"
config SX9500_INIT_PRIORITY
int
depends on SX9500
default 70
prompt "Init priority"
help
Device driver initialization priority.
config SX9500_I2C_ADDR
hex "SX9500 I2C slave address"
depends on SX9500
default 0x2B
help
Specify the I2C slave address for the SX9500.
config SX9500_I2C_DEV_NAME
string "I2C master where SX9500 is connected"
depends on SX9500
default "I2C_0"
help
Specify the device name of the I2C master device to which SX9500 is
connected.
config SX9500_PROX_CHANNEL
int
default 3
depends on SX9500
prompt "Proximity channel to use"
help
The SX9500 offers 4 separate proximity channels. Choose which one
you are using. Valid numbers are 0 to 3.
choice
prompt "SX9500 trigger mode"
depends on SX9500
default SX9500_TRIGGER_GLOBAL_FIBER
config SX9500_TRIGGER_NONE
bool "No trigger"
config SX9500_TRIGGER_GLOBAL_FIBER
depends on GPIO
select SX9500_TRIGGER
select SENSOR_DELAYED_WORK
bool "Use global fiber"
config SX9500_TRIGGER_OWN_FIBER
depends on GPIO
select SX9500_TRIGGER
bool "Use own fiber"
endchoice
config SX9500_TRIGGER
bool
depends on SX9500
config SX9500_GPIO_CONTROLLER
string "GPIO controller for SX9500 interrupt"
depends on SX9500 && SX9500_TRIGGER
default GPIO_0
help
Specify the device name of the GPIO controller the SX9500 interrupt
is connected to.
config SX9500_GPIO_PIN
int "GPIO pin for SX9500 interrupt"
depends on SX9500 && SX9500_TRIGGER
default 3
config SX9500_FIBER_STACK_SIZE
int "Sensor delayed work fiber stack size"
depends on SX9500 && SX9500_TRIGGER_OWN_FIBER
default 1024
config SX9500_FIBER_PRIORITY
int "Fiber priority"
depends on SX9500 && SX9500_TRIGGER_OWN_FIBER
default 10
|