Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 | /**
******************************************************************************
* @file stm32f7xx_hal_flash_ex.c
* @author MCD Application Team
* @brief Extended FLASH HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the FLASH extension peripheral:
* + Extended programming operations functions
*
@verbatim
==============================================================================
##### Flash Extension features #####
==============================================================================
[..] Comparing to other previous devices, the FLASH interface for STM32F76xx/STM32F77xx
devices contains the following additional features
(+) Capacity up to 2 Mbyte with dual bank architecture supporting read-while-write
capability (RWW)
(+) Dual bank memory organization
(+) Dual boot mode
##### How to use this driver #####
==============================================================================
[..] This driver provides functions to configure and program the FLASH memory
of all STM32F7xx devices. It includes
(#) FLASH Memory Erase functions:
(++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and
HAL_FLASH_Lock() functions
(++) Erase function: Erase sector, erase all sectors
(++) There are two modes of erase :
(+++) Polling Mode using HAL_FLASHEx_Erase()
(+++) Interrupt Mode using HAL_FLASHEx_Erase_IT()
(#) Option Bytes Programming functions: Use HAL_FLASHEx_OBProgram() to :
(++) Set/Reset the write protection
(++) Set the Read protection Level
(++) Set the BOR level
(++) Program the user Option Bytes
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal.h"
/** @addtogroup STM32F7xx_HAL_Driver
* @{
*/
/** @defgroup FLASHEx FLASHEx
* @brief FLASH HAL Extension module driver
* @{
*/
#ifdef HAL_FLASH_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @addtogroup FLASHEx_Private_Constants
* @{
*/
#define SECTOR_MASK 0xFFFFFF07U
#define FLASH_TIMEOUT_VALUE 50000U/* 50 s */
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/** @addtogroup FLASHEx_Private_Variables
* @{
*/
extern FLASH_ProcessTypeDef pFlash;
/**
* @}
*/
/* Private function prototypes -----------------------------------------------*/
/** @addtogroup FLASHEx_Private_Functions
* @{
*/
/* Option bytes control */
static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WRPSector);
static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WRPSector);
static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t Level);
static HAL_StatusTypeDef FLASH_OB_BOR_LevelConfig(uint8_t Level);
static HAL_StatusTypeDef FLASH_OB_BootAddressConfig(uint32_t BootOption, uint32_t Address);
static uint32_t FLASH_OB_GetUser(void);
static uint32_t FLASH_OB_GetWRP(void);
static uint8_t FLASH_OB_GetRDP(void);
static uint32_t FLASH_OB_GetBOR(void);
static uint32_t FLASH_OB_GetBootAddress(uint32_t BootOption);
#if defined (FLASH_OPTCR_nDBANK)
static void FLASH_MassErase(uint8_t VoltageRange, uint32_t Banks);
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t Wwdg, uint32_t Iwdg, uint32_t Stop, uint32_t Stdby, uint32_t Iwdgstop, \
uint32_t Iwdgstdby, uint32_t NDBank, uint32_t NDBoot);
#else
static void FLASH_MassErase(uint8_t VoltageRange);
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t Wwdg, uint32_t Iwdg, uint32_t Stop, uint32_t Stdby, uint32_t Iwdgstop, uint32_t Iwdgstdby);
#endif /* FLASH_OPTCR_nDBANK */
#if defined (FLASH_OPTCR2_PCROP)
static HAL_StatusTypeDef FLASH_OB_PCROP_Config(uint32_t PCROPSector);
static HAL_StatusTypeDef FLASH_OB_PCROP_RDP_Config(uint32_t Pcrop_Rdp);
static uint32_t FLASH_OB_GetPCROP(void);
static uint32_t FLASH_OB_GetPCROPRDP(void);
#endif /* FLASH_OPTCR2_PCROP */
extern HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout);
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions
* @{
*/
/** @defgroup FLASHEx_Exported_Functions_Group1 Extended IO operation functions
* @brief Extended IO operation functions
*
@verbatim
===============================================================================
##### Extended programming operation functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to manage the Extension FLASH
programming operations Operations.
@endverbatim
* @{
*/
/**
* @brief Perform a mass erase or erase the specified FLASH memory sectors
* @param[in] pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
* contains the configuration information for the erasing.
*
* @param[out] SectorError pointer to variable that
* contains the configuration information on faulty sector in case of error
* (0xFFFFFFFF means that all the sectors have been correctly erased)
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *SectorError)
{
HAL_StatusTypeDef status = HAL_ERROR;
uint32_t index = 0;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
/*Initialization of SectorError variable*/
*SectorError = 0xFFFFFFFFU;
if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
{
/*Mass erase to be done*/
#if defined (FLASH_OPTCR_nDBANK)
FLASH_MassErase((uint8_t) pEraseInit->VoltageRange, pEraseInit->Banks);
#else
FLASH_MassErase((uint8_t) pEraseInit->VoltageRange);
#endif /* FLASH_OPTCR_nDBANK */
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* if the erase operation is completed, disable the MER Bit */
FLASH->CR &= (~FLASH_MER_BIT);
}
else
{
/* Check the parameters */
assert_param(IS_FLASH_NBSECTORS(pEraseInit->NbSectors + pEraseInit->Sector));
/* Erase by sector by sector to be done*/
for(index = pEraseInit->Sector; index < (pEraseInit->NbSectors + pEraseInit->Sector); index++)
{
FLASH_Erase_Sector(index, (uint8_t) pEraseInit->VoltageRange);
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
/* If the erase operation is completed, disable the SER Bit and SNB Bits */
CLEAR_BIT(FLASH->CR, (FLASH_CR_SER | FLASH_CR_SNB));
if(status != HAL_OK)
{
/* In case of error, stop erase procedure and return the faulty sector*/
*SectorError = index;
break;
}
}
}
}
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Perform a mass erase or erase the specified FLASH memory sectors with interrupt enabled
* @param pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
* contains the configuration information for the erasing.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit)
{
HAL_StatusTypeDef status = HAL_OK;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
/* Enable End of FLASH Operation interrupt */
__HAL_FLASH_ENABLE_IT(FLASH_IT_EOP);
/* Enable Error source interrupt */
__HAL_FLASH_ENABLE_IT(FLASH_IT_ERR);
/* Clear pending flags (if any) */
__HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |\
FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR| FLASH_FLAG_ERSERR);
if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
{
/*Mass erase to be done*/
pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE;
#if defined (FLASH_OPTCR_nDBANK)
FLASH_MassErase((uint8_t) pEraseInit->VoltageRange, pEraseInit->Banks);
#else
FLASH_MassErase((uint8_t) pEraseInit->VoltageRange);
#endif /* FLASH_OPTCR_nDBANK */
}
else
{
/* Erase by sector to be done*/
/* Check the parameters */
assert_param(IS_FLASH_NBSECTORS(pEraseInit->NbSectors + pEraseInit->Sector));
pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE;
pFlash.NbSectorsToErase = pEraseInit->NbSectors;
pFlash.Sector = pEraseInit->Sector;
pFlash.VoltageForErase = (uint8_t)pEraseInit->VoltageRange;
/*Erase 1st sector and wait for IT*/
FLASH_Erase_Sector(pEraseInit->Sector, pEraseInit->VoltageRange);
}
return status;
}
/**
* @brief Program option bytes
* @param pOBInit pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval HAL Status
*/
HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
{
HAL_StatusTypeDef status = HAL_ERROR;
/* Process Locked */
__HAL_LOCK(&pFlash);
/* Check the parameters */
assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
/* Write protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
{
assert_param(IS_WRPSTATE(pOBInit->WRPState));
if(pOBInit->WRPState == OB_WRPSTATE_ENABLE)
{
/*Enable of Write protection on the selected Sector*/
status = FLASH_OB_EnableWRP(pOBInit->WRPSector);
}
else
{
/*Disable of Write protection on the selected Sector*/
status = FLASH_OB_DisableWRP(pOBInit->WRPSector);
}
}
/* Read protection configuration */
if((pOBInit->OptionType & OPTIONBYTE_RDP) == OPTIONBYTE_RDP)
{
status = FLASH_OB_RDP_LevelConfig(pOBInit->RDPLevel);
}
/* USER configuration */
if((pOBInit->OptionType & OPTIONBYTE_USER) == OPTIONBYTE_USER)
{
#if defined (FLASH_OPTCR_nDBANK)
status = FLASH_OB_UserConfig(pOBInit->USERConfig & OB_WWDG_SW,
pOBInit->USERConfig & OB_IWDG_SW,
pOBInit->USERConfig & OB_STOP_NO_RST,
pOBInit->USERConfig & OB_STDBY_NO_RST,
pOBInit->USERConfig & OB_IWDG_STOP_ACTIVE,
pOBInit->USERConfig & OB_IWDG_STDBY_ACTIVE,
pOBInit->USERConfig & OB_NDBANK_SINGLE_BANK,
pOBInit->USERConfig & OB_DUAL_BOOT_DISABLE);
#else
status = FLASH_OB_UserConfig(pOBInit->USERConfig & OB_WWDG_SW,
pOBInit->USERConfig & OB_IWDG_SW,
pOBInit->USERConfig & OB_STOP_NO_RST,
pOBInit->USERConfig & OB_STDBY_NO_RST,
pOBInit->USERConfig & OB_IWDG_STOP_ACTIVE,
pOBInit->USERConfig & OB_IWDG_STDBY_ACTIVE);
#endif /* FLASH_OPTCR_nDBANK */
}
/* BOR Level configuration */
if((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR)
{
status = FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel);
}
/* Boot 0 Address configuration */
if((pOBInit->OptionType & OPTIONBYTE_BOOTADDR_0) == OPTIONBYTE_BOOTADDR_0)
{
status = FLASH_OB_BootAddressConfig(OPTIONBYTE_BOOTADDR_0, pOBInit->BootAddr0);
}
/* Boot 1 Address configuration */
if((pOBInit->OptionType & OPTIONBYTE_BOOTADDR_1) == OPTIONBYTE_BOOTADDR_1)
{
status = FLASH_OB_BootAddressConfig(OPTIONBYTE_BOOTADDR_1, pOBInit->BootAddr1);
}
#if defined (FLASH_OPTCR2_PCROP)
/* PCROP configuration */
if((pOBInit->OptionType & OPTIONBYTE_PCROP) == OPTIONBYTE_PCROP)
{
status = FLASH_OB_PCROP_Config(pOBInit->PCROPSector);
}
/* PCROP_RDP configuration */
if((pOBInit->OptionType & OPTIONBYTE_PCROP_RDP) == OPTIONBYTE_PCROP_RDP)
{
status = FLASH_OB_PCROP_RDP_Config(pOBInit->PCROPRdp);
}
#endif /* FLASH_OPTCR2_PCROP */
/* Process Unlocked */
__HAL_UNLOCK(&pFlash);
return status;
}
/**
* @brief Get the Option byte configuration
* @param pOBInit pointer to an FLASH_OBInitStruct structure that
* contains the configuration information for the programming.
*
* @retval None
*/
void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit)
{
pOBInit->OptionType = OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER |\
OPTIONBYTE_BOR | OPTIONBYTE_BOOTADDR_0 | OPTIONBYTE_BOOTADDR_1;
/*Get WRP*/
pOBInit->WRPSector = FLASH_OB_GetWRP();
/*Get RDP Level*/
pOBInit->RDPLevel = FLASH_OB_GetRDP();
/*Get USER*/
pOBInit->USERConfig = FLASH_OB_GetUser();
/*Get BOR Level*/
pOBInit->BORLevel = FLASH_OB_GetBOR();
/*Get Boot Address when Boot pin = 0 */
pOBInit->BootAddr0 = FLASH_OB_GetBootAddress(OPTIONBYTE_BOOTADDR_0);
/*Get Boot Address when Boot pin = 1 */
pOBInit->BootAddr1 = FLASH_OB_GetBootAddress(OPTIONBYTE_BOOTADDR_1);
#if defined (FLASH_OPTCR2_PCROP)
/*Get PCROP Sectors */
pOBInit->PCROPSector = FLASH_OB_GetPCROP();
/*Get PCROP_RDP Value */
pOBInit->PCROPRdp = FLASH_OB_GetPCROPRDP();
#endif /* FLASH_OPTCR2_PCROP */
}
/**
* @}
*/
#if defined (FLASH_OPTCR_nDBANK)
/**
* @brief Full erase of FLASH memory sectors
* @param VoltageRange The device voltage range which defines the erase parallelism.
* This parameter can be one of the following values:
* @arg VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V,
* the operation will be done by byte (8-bit)
* @arg VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V,
* the operation will be done by half word (16-bit)
* @arg VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V,
* the operation will be done by word (32-bit)
* @arg VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp,
* the operation will be done by double word (64-bit)
* @param Banks Banks to be erased
* This parameter can be one of the following values:
* @arg FLASH_BANK_1: Bank1 to be erased
* @arg FLASH_BANK_2: Bank2 to be erased
* @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
*
* @retval HAL Status
*/
static void FLASH_MassErase(uint8_t VoltageRange, uint32_t Banks)
{
/* Check the parameters */
assert_param(IS_VOLTAGERANGE(VoltageRange));
assert_param(IS_FLASH_BANK(Banks));
/* if the previous operation is completed, proceed to erase all sectors */
FLASH->CR &= CR_PSIZE_MASK;
if(Banks == FLASH_BANK_BOTH)
{
/* bank1 & bank2 will be erased*/
FLASH->CR |= FLASH_MER_BIT;
}
else if(Banks == FLASH_BANK_2)
{
/*Only bank2 will be erased*/
FLASH->CR |= FLASH_CR_MER2;
}
else
{
/*Only bank1 will be erased*/
FLASH->CR |= FLASH_CR_MER1;
}
FLASH->CR |= FLASH_CR_STRT | ((uint32_t)VoltageRange <<8);
/* Data synchronous Barrier (DSB) Just after the write operation
This will force the CPU to respect the sequence of instruction (no optimization).*/
__DSB();
}
/**
* @brief Erase the specified FLASH memory sector
* @param Sector FLASH sector to erase
* The value of this parameter depend on device used within the same series
* @param VoltageRange The device voltage range which defines the erase parallelism.
* This parameter can be one of the following values:
* @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V,
* the operation will be done by byte (8-bit)
* @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V,
* the operation will be done by half word (16-bit)
* @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V,
* the operation will be done by word (32-bit)
* @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp,
* the operation will be done by double word (64-bit)
*
* @retval None
*/
void FLASH_Erase_Sector(uint32_t Sector, uint8_t VoltageRange)
{
uint32_t tmp_psize = 0;
/* Check the parameters */
assert_param(IS_FLASH_SECTOR(Sector));
assert_param(IS_VOLTAGERANGE(VoltageRange));
if(VoltageRange == FLASH_VOLTAGE_RANGE_1)
{
tmp_psize = FLASH_PSIZE_BYTE;
}
else if(VoltageRange == FLASH_VOLTAGE_RANGE_2)
{
tmp_psize = FLASH_PSIZE_HALF_WORD;
}
else if(VoltageRange == FLASH_VOLTAGE_RANGE_3)
{
tmp_psize = FLASH_PSIZE_WORD;
}
else
{
tmp_psize = FLASH_PSIZE_DOUBLE_WORD;
}
/* Need to add offset of 4 when sector higher than FLASH_SECTOR_11 */
if(Sector > FLASH_SECTOR_11)
{
Sector += 4;
}
/* If the previous operation is completed, proceed to erase the sector */
FLASH->CR &= CR_PSIZE_MASK;
FLASH->CR |= tmp_psize;
CLEAR_BIT(FLASH->CR, FLASH_CR_SNB);
FLASH->CR |= FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos);
FLASH->CR |= FLASH_CR_STRT;
/* Data synchronous Barrier (DSB) Just after the write operation
This will force the CPU to respect the sequence of instruction (no optimization).*/
__DSB();
}
/**
* @brief Return the FLASH Write Protection Option Bytes value.
* @retval uint32_t FLASH Write Protection Option Bytes value
*/
static uint32_t FLASH_OB_GetWRP(void)
{
/* Return the FLASH write protection Register value */
return ((uint32_t)(FLASH->OPTCR & 0x0FFF0000));
}
/**
* @brief Program the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY.
* @param Wwdg Selects the IWDG mode
* This parameter can be one of the following values:
* @arg OB_WWDG_SW: Software WWDG selected
* @arg OB_WWDG_HW: Hardware WWDG selected
* @param Iwdg Selects the WWDG mode
* This parameter can be one of the following values:
* @arg OB_IWDG_SW: Software IWDG selected
* @arg OB_IWDG_HW: Hardware IWDG selected
* @param Stop Reset event when entering STOP mode.
* This parameter can be one of the following values:
* @arg OB_STOP_NO_RST: No reset generated when entering in STOP
* @arg OB_STOP_RST: Reset generated when entering in STOP
* @param Stdby Reset event when entering Standby mode.
* This parameter can be one of the following values:
* @arg OB_STDBY_NO_RST: No reset generated when entering in STANDBY
* @arg OB_STDBY_RST: Reset generated when entering in STANDBY
* @param Iwdgstop Independent watchdog counter freeze in Stop mode.
* This parameter can be one of the following values:
* @arg OB_IWDG_STOP_FREEZE: Freeze IWDG counter in STOP
* @arg OB_IWDG_STOP_ACTIVE: IWDG counter active in STOP
* @param Iwdgstdby Independent watchdog counter freeze in standby mode.
* This parameter can be one of the following values:
* @arg OB_IWDG_STDBY_FREEZE: Freeze IWDG counter in STANDBY
* @arg OB_IWDG_STDBY_ACTIVE: IWDG counter active in STANDBY
* @param NDBank Flash Single Bank mode enabled.
* This parameter can be one of the following values:
* @arg OB_NDBANK_SINGLE_BANK: enable 256 bits mode (Flash is a single bank)
* @arg OB_NDBANK_DUAL_BANK: disable 256 bits mode (Flash is a dual bank in 128 bits mode)
* @param NDBoot Flash Dual boot mode disable.
* This parameter can be one of the following values:
* @arg OB_DUAL_BOOT_DISABLE: Disable Dual Boot
* @arg OB_DUAL_BOOT_ENABLE: Enable Dual Boot
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t Wwdg, uint32_t Iwdg, uint32_t Stop, uint32_t Stdby, uint32_t Iwdgstop, \
uint32_t Iwdgstdby, uint32_t NDBank, uint32_t NDBoot)
{
uint32_t useroptionmask = 0x00;
uint32_t useroptionvalue = 0x00;
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_WWDG_SOURCE(Wwdg));
assert_param(IS_OB_IWDG_SOURCE(Iwdg));
assert_param(IS_OB_STOP_SOURCE(Stop));
assert_param(IS_OB_STDBY_SOURCE(Stdby));
assert_param(IS_OB_IWDG_STOP_FREEZE(Iwdgstop));
assert_param(IS_OB_IWDG_STDBY_FREEZE(Iwdgstdby));
assert_param(IS_OB_NDBANK(NDBank));
assert_param(IS_OB_NDBOOT(NDBoot));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
useroptionmask = (FLASH_OPTCR_WWDG_SW | FLASH_OPTCR_IWDG_SW | FLASH_OPTCR_nRST_STOP | \
FLASH_OPTCR_nRST_STDBY | FLASH_OPTCR_IWDG_STOP | FLASH_OPTCR_IWDG_STDBY | \
FLASH_OPTCR_nDBOOT | FLASH_OPTCR_nDBANK);
useroptionvalue = (Iwdg | Wwdg | Stop | Stdby | Iwdgstop | Iwdgstdby | NDBoot | NDBank);
/* Update User Option Byte */
MODIFY_REG(FLASH->OPTCR, useroptionmask, useroptionvalue);
}
return status;
}
/**
* @brief Return the FLASH User Option Byte value.
* @retval uint32_t FLASH User Option Bytes values: WWDG_SW(Bit4), IWDG_SW(Bit5), nRST_STOP(Bit6),
* nRST_STDBY(Bit7), nDBOOT(Bit28), nDBANK(Bit29), IWDG_STDBY(Bit30) and IWDG_STOP(Bit31).
*/
static uint32_t FLASH_OB_GetUser(void)
{
/* Return the User Option Byte */
return ((uint32_t)(FLASH->OPTCR & 0xF00000F0U));
}
#else
/**
* @brief Full erase of FLASH memory sectors
* @param VoltageRange The device voltage range which defines the erase parallelism.
* This parameter can be one of the following values:
* @arg VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V,
* the operation will be done by byte (8-bit)
* @arg VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V,
* the operation will be done by half word (16-bit)
* @arg VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V,
* the operation will be done by word (32-bit)
* @arg VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp,
* the operation will be done by double word (64-bit)
*
* @retval HAL Status
*/
static void FLASH_MassErase(uint8_t VoltageRange)
{
/* Check the parameters */
assert_param(IS_VOLTAGERANGE(VoltageRange));
/* if the previous operation is completed, proceed to erase all sectors */
FLASH->CR &= CR_PSIZE_MASK;
FLASH->CR |= FLASH_CR_MER;
FLASH->CR |= FLASH_CR_STRT | ((uint32_t)VoltageRange <<8);
/* Data synchronous Barrier (DSB) Just after the write operation
This will force the CPU to respect the sequence of instruction (no optimization).*/
__DSB();
}
/**
* @brief Erase the specified FLASH memory sector
* @param Sector FLASH sector to erase
* The value of this parameter depend on device used within the same series
* @param VoltageRange The device voltage range which defines the erase parallelism.
* This parameter can be one of the following values:
* @arg FLASH_VOLTAGE_RANGE_1: when the device voltage range is 1.8V to 2.1V,
* the operation will be done by byte (8-bit)
* @arg FLASH_VOLTAGE_RANGE_2: when the device voltage range is 2.1V to 2.7V,
* the operation will be done by half word (16-bit)
* @arg FLASH_VOLTAGE_RANGE_3: when the device voltage range is 2.7V to 3.6V,
* the operation will be done by word (32-bit)
* @arg FLASH_VOLTAGE_RANGE_4: when the device voltage range is 2.7V to 3.6V + External Vpp,
* the operation will be done by double word (64-bit)
*
* @retval None
*/
void FLASH_Erase_Sector(uint32_t Sector, uint8_t VoltageRange)
{
uint32_t tmp_psize = 0;
/* Check the parameters */
assert_param(IS_FLASH_SECTOR(Sector));
assert_param(IS_VOLTAGERANGE(VoltageRange));
if(VoltageRange == FLASH_VOLTAGE_RANGE_1)
{
tmp_psize = FLASH_PSIZE_BYTE;
}
else if(VoltageRange == FLASH_VOLTAGE_RANGE_2)
{
tmp_psize = FLASH_PSIZE_HALF_WORD;
}
else if(VoltageRange == FLASH_VOLTAGE_RANGE_3)
{
tmp_psize = FLASH_PSIZE_WORD;
}
else
{
tmp_psize = FLASH_PSIZE_DOUBLE_WORD;
}
/* If the previous operation is completed, proceed to erase the sector */
FLASH->CR &= CR_PSIZE_MASK;
FLASH->CR |= tmp_psize;
FLASH->CR &= SECTOR_MASK;
FLASH->CR |= FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos);
FLASH->CR |= FLASH_CR_STRT;
/* Data synchronous Barrier (DSB) Just after the write operation
This will force the CPU to respect the sequence of instruction (no optimization).*/
__DSB();
}
/**
* @brief Return the FLASH Write Protection Option Bytes value.
* @retval uint32_t FLASH Write Protection Option Bytes value
*/
static uint32_t FLASH_OB_GetWRP(void)
{
/* Return the FLASH write protection Register value */
return ((uint32_t)(FLASH->OPTCR & 0x00FF0000));
}
/**
* @brief Program the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY.
* @param Wwdg Selects the IWDG mode
* This parameter can be one of the following values:
* @arg OB_WWDG_SW: Software WWDG selected
* @arg OB_WWDG_HW: Hardware WWDG selected
* @param Iwdg Selects the WWDG mode
* This parameter can be one of the following values:
* @arg OB_IWDG_SW: Software IWDG selected
* @arg OB_IWDG_HW: Hardware IWDG selected
* @param Stop Reset event when entering STOP mode.
* This parameter can be one of the following values:
* @arg OB_STOP_NO_RST: No reset generated when entering in STOP
* @arg OB_STOP_RST: Reset generated when entering in STOP
* @param Stdby Reset event when entering Standby mode.
* This parameter can be one of the following values:
* @arg OB_STDBY_NO_RST: No reset generated when entering in STANDBY
* @arg OB_STDBY_RST: Reset generated when entering in STANDBY
* @param Iwdgstop Independent watchdog counter freeze in Stop mode.
* This parameter can be one of the following values:
* @arg OB_IWDG_STOP_FREEZE: Freeze IWDG counter in STOP
* @arg OB_IWDG_STOP_ACTIVE: IWDG counter active in STOP
* @param Iwdgstdby Independent watchdog counter freeze in standby mode.
* This parameter can be one of the following values:
* @arg OB_IWDG_STDBY_FREEZE: Freeze IWDG counter in STANDBY
* @arg OB_IWDG_STDBY_ACTIVE: IWDG counter active in STANDBY
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_UserConfig(uint32_t Wwdg, uint32_t Iwdg, uint32_t Stop, uint32_t Stdby, uint32_t Iwdgstop, uint32_t Iwdgstdby)
{
uint32_t useroptionmask = 0x00;
uint32_t useroptionvalue = 0x00;
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_WWDG_SOURCE(Wwdg));
assert_param(IS_OB_IWDG_SOURCE(Iwdg));
assert_param(IS_OB_STOP_SOURCE(Stop));
assert_param(IS_OB_STDBY_SOURCE(Stdby));
assert_param(IS_OB_IWDG_STOP_FREEZE(Iwdgstop));
assert_param(IS_OB_IWDG_STDBY_FREEZE(Iwdgstdby));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
useroptionmask = (FLASH_OPTCR_WWDG_SW | FLASH_OPTCR_IWDG_SW | FLASH_OPTCR_nRST_STOP | \
FLASH_OPTCR_nRST_STDBY | FLASH_OPTCR_IWDG_STOP | FLASH_OPTCR_IWDG_STDBY);
useroptionvalue = (Iwdg | Wwdg | Stop | Stdby | Iwdgstop | Iwdgstdby);
/* Update User Option Byte */
MODIFY_REG(FLASH->OPTCR, useroptionmask, useroptionvalue);
}
return status;
}
/**
* @brief Return the FLASH User Option Byte value.
* @retval uint32_t FLASH User Option Bytes values: WWDG_SW(Bit4), IWDG_SW(Bit5), nRST_STOP(Bit6),
* nRST_STDBY(Bit7), IWDG_STDBY(Bit30) and IWDG_STOP(Bit31).
*/
static uint32_t FLASH_OB_GetUser(void)
{
/* Return the User Option Byte */
return ((uint32_t)(FLASH->OPTCR & 0xC00000F0U));
}
#endif /* FLASH_OPTCR_nDBANK */
/**
* @brief Enable the write protection of the desired bank1 or bank2 sectors
*
* @note When the memory read protection level is selected (RDP level = 1),
* it is not possible to program or erase the flash sector i if CortexM7
* debug features are connected or boot code is executed in RAM, even if nWRPi = 1
*
* @param WRPSector specifies the sector(s) to be write protected.
* This parameter can be one of the following values:
* @arg WRPSector: A value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_7 (for STM32F74xxx/STM32F75xxx devices)
* or a value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_11 (in Single Bank mode for STM32F76xxx/STM32F77xxx devices)
* or a value between OB_WRP_DB_SECTOR_0 and OB_WRP_DB_SECTOR_23 (in Dual Bank mode for STM32F76xxx/STM32F77xxx devices)
* @arg OB_WRP_SECTOR_All
*
* @retval HAL FLASH State
*/
static HAL_StatusTypeDef FLASH_OB_EnableWRP(uint32_t WRPSector)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_WRP_SECTOR(WRPSector));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
/*Write protection enabled on sectors */
FLASH->OPTCR &= (~WRPSector);
}
return status;
}
/**
* @brief Disable the write protection of the desired bank1 or bank 2 sectors
*
* @note When the memory read protection level is selected (RDP level = 1),
* it is not possible to program or erase the flash sector i if CortexM4
* debug features are connected or boot code is executed in RAM, even if nWRPi = 1
*
* @param WRPSector specifies the sector(s) to be write protected.
* This parameter can be one of the following values:
* @arg WRPSector: A value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_7 (for STM32F74xxx/STM32F75xxx devices)
* or a value between OB_WRP_SECTOR_0 and OB_WRP_SECTOR_11 (in Single Bank mode for STM32F76xxx/STM32F77xxx devices)
* or a value between OB_WRP_DB_SECTOR_0 and OB_WRP_DB_SECTOR_23 (in Dual Bank mode for STM32F76xxx/STM32F77xxx devices)
* @arg OB_WRP_Sector_All
*
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_DisableWRP(uint32_t WRPSector)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_WRP_SECTOR(WRPSector));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
/* Write protection disabled on sectors */
FLASH->OPTCR |= (WRPSector);
}
return status;
}
/**
* @brief Set the read protection level.
* @param Level specifies the read protection level.
* This parameter can be one of the following values:
* @arg OB_RDP_LEVEL_0: No protection
* @arg OB_RDP_LEVEL_1: Read protection of the memory
* @arg OB_RDP_LEVEL_2: Full chip protection
*
* @note WARNING: When enabling OB_RDP level 2 it's no more possible to go back to level 1 or 0
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_RDP_LevelConfig(uint8_t Level)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_RDP_LEVEL(Level));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
*(__IO uint8_t*)OPTCR_BYTE1_ADDRESS = Level;
}
return status;
}
/**
* @brief Set the BOR Level.
* @param Level specifies the Option Bytes BOR Reset Level.
* This parameter can be one of the following values:
* @arg OB_BOR_LEVEL3: Supply voltage ranges from 2.7 to 3.6 V
* @arg OB_BOR_LEVEL2: Supply voltage ranges from 2.4 to 2.7 V
* @arg OB_BOR_LEVEL1: Supply voltage ranges from 2.1 to 2.4 V
* @arg OB_BOR_OFF: Supply voltage ranges from 1.62 to 2.1 V
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_BOR_LevelConfig(uint8_t Level)
{
/* Check the parameters */
assert_param(IS_OB_BOR_LEVEL(Level));
/* Set the BOR Level */
MODIFY_REG(FLASH->OPTCR, FLASH_OPTCR_BOR_LEV, Level);
return HAL_OK;
}
/**
* @brief Configure Boot base address.
*
* @param BootOption specifies Boot base address depending from Boot pin = 0 or pin = 1
* This parameter can be one of the following values:
* @arg OPTIONBYTE_BOOTADDR_0 : Boot address based when Boot pin = 0
* @arg OPTIONBYTE_BOOTADDR_1 : Boot address based when Boot pin = 1
* @param Address specifies Boot base address
* This parameter can be one of the following values:
* @arg OB_BOOTADDR_ITCM_RAM : Boot from ITCM RAM (0x00000000)
* @arg OB_BOOTADDR_SYSTEM : Boot from System memory bootloader (0x00100000)
* @arg OB_BOOTADDR_ITCM_FLASH : Boot from Flash on ITCM interface (0x00200000)
* @arg OB_BOOTADDR_AXIM_FLASH : Boot from Flash on AXIM interface (0x08000000)
* @arg OB_BOOTADDR_DTCM_RAM : Boot from DTCM RAM (0x20000000)
* @arg OB_BOOTADDR_SRAM1 : Boot from SRAM1 (0x20010000)
* @arg OB_BOOTADDR_SRAM2 : Boot from SRAM2 (0x2004C000)
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_BootAddressConfig(uint32_t BootOption, uint32_t Address)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_BOOT_ADDRESS(Address));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
if(BootOption == OPTIONBYTE_BOOTADDR_0)
{
MODIFY_REG(FLASH->OPTCR1, FLASH_OPTCR1_BOOT_ADD0, Address);
}
else
{
MODIFY_REG(FLASH->OPTCR1, FLASH_OPTCR1_BOOT_ADD1, (Address << 16));
}
}
return status;
}
/**
* @brief Returns the FLASH Read Protection level.
* @retval FlagStatus FLASH ReadOut Protection Status:
* This parameter can be one of the following values:
* @arg OB_RDP_LEVEL_0: No protection
* @arg OB_RDP_LEVEL_1: Read protection of the memory
* @arg OB_RDP_LEVEL_2: Full chip protection
*/
static uint8_t FLASH_OB_GetRDP(void)
{
uint8_t readstatus = OB_RDP_LEVEL_0;
if ((*(__IO uint8_t*)(OPTCR_BYTE1_ADDRESS)) == OB_RDP_LEVEL_0)
{
readstatus = OB_RDP_LEVEL_0;
}
else if ((*(__IO uint8_t*)(OPTCR_BYTE1_ADDRESS)) == OB_RDP_LEVEL_2)
{
readstatus = OB_RDP_LEVEL_2;
}
else
{
readstatus = OB_RDP_LEVEL_1;
}
return readstatus;
}
/**
* @brief Returns the FLASH BOR level.
* @retval uint32_t The FLASH BOR level:
* - OB_BOR_LEVEL3: Supply voltage ranges from 2.7 to 3.6 V
* - OB_BOR_LEVEL2: Supply voltage ranges from 2.4 to 2.7 V
* - OB_BOR_LEVEL1: Supply voltage ranges from 2.1 to 2.4 V
* - OB_BOR_OFF : Supply voltage ranges from 1.62 to 2.1 V
*/
static uint32_t FLASH_OB_GetBOR(void)
{
/* Return the FLASH BOR level */
return ((uint32_t)(FLASH->OPTCR & 0x0C));
}
/**
* @brief Configure Boot base address.
*
* @param BootOption specifies Boot base address depending from Boot pin = 0 or pin = 1
* This parameter can be one of the following values:
* @arg OPTIONBYTE_BOOTADDR_0 : Boot address based when Boot pin = 0
* @arg OPTIONBYTE_BOOTADDR_1 : Boot address based when Boot pin = 1
*
* @retval uint32_t Boot Base Address:
* - OB_BOOTADDR_ITCM_RAM : Boot from ITCM RAM (0x00000000)
* - OB_BOOTADDR_SYSTEM : Boot from System memory bootloader (0x00100000)
* - OB_BOOTADDR_ITCM_FLASH : Boot from Flash on ITCM interface (0x00200000)
* - OB_BOOTADDR_AXIM_FLASH : Boot from Flash on AXIM interface (0x08000000)
* - OB_BOOTADDR_DTCM_RAM : Boot from DTCM RAM (0x20000000)
* - OB_BOOTADDR_SRAM1 : Boot from SRAM1 (0x20010000)
* - OB_BOOTADDR_SRAM2 : Boot from SRAM2 (0x2004C000)
*/
static uint32_t FLASH_OB_GetBootAddress(uint32_t BootOption)
{
uint32_t Address = 0;
/* Return the Boot base Address */
if(BootOption == OPTIONBYTE_BOOTADDR_0)
{
Address = FLASH->OPTCR1 & FLASH_OPTCR1_BOOT_ADD0;
}
else
{
Address = ((FLASH->OPTCR1 & FLASH_OPTCR1_BOOT_ADD1) >> 16);
}
return Address;
}
#if defined (FLASH_OPTCR2_PCROP)
/**
* @brief Set the PCROP protection for sectors.
* @param PCROPSector specifies the sector(s) to be PCROP protected.
* This parameter can be one of the following values:
* @arg OB_PCROP_SECTOR_x: A value between OB_PCROP_SECTOR_0 and OB_PCROP_SECTOR_7
* @arg OB_PCROP_SECTOR_ALL
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_PCROP_Config(uint32_t PCROPSector)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_PCROP_SECTOR(PCROPSector));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
MODIFY_REG(FLASH->OPTCR2, FLASH_OPTCR2_PCROP, PCROPSector);
}
return status;
}
/**
* @brief Set the PCROP_RDP value
* @param Pcrop_Rdp specifies the PCROP_RDP bit value.
*
* @retval HAL Status
*/
static HAL_StatusTypeDef FLASH_OB_PCROP_RDP_Config(uint32_t Pcrop_Rdp)
{
HAL_StatusTypeDef status = HAL_OK;
/* Check the parameters */
assert_param(IS_OB_PCROP_RDP_VALUE(Pcrop_Rdp));
/* Wait for last operation to be completed */
status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
if(status == HAL_OK)
{
MODIFY_REG(FLASH->OPTCR2, FLASH_OPTCR2_PCROP_RDP, Pcrop_Rdp);
}
return status;
}
/**
* @brief Return the FLASH PCROP Protection Option Bytes value.
* @retval uint32_t FLASH PCROP Protection Option Bytes value
*/
static uint32_t FLASH_OB_GetPCROP(void)
{
/* Return the FLASH write protection Register value */
return ((uint32_t)(FLASH->OPTCR2 & FLASH_OPTCR2_PCROP));
}
/**
* @brief Return the FLASH PCROP_RDP option byte value.
* @retval uint32_t FLASH PCROP_RDP option byte value
*/
static uint32_t FLASH_OB_GetPCROPRDP(void)
{
/* Return the FLASH write protection Register value */
return ((uint32_t)(FLASH->OPTCR2 & FLASH_OPTCR2_PCROP_RDP));
}
#endif /* FLASH_OPTCR2_PCROP */
/**
* @}
*/
#endif /* HAL_FLASH_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|