Boot Linux faster!

Check our new training course

Boot Linux faster!

Check our new training course
and Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

/*
 * Copyright (c) 2017 Linaro Limited
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <st/l4/stm32l4-pinctrl.dtsi>

#include <arm/armv7-m.dtsi>
#include <dt-bindings/clock/stm32_clock.h>
#include <dt-bindings/i2c/i2c.h>
#include <dt-bindings/gpio/gpio.h>

/ {
	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-m4f";
			reg = <0>;
		};
	};

	sram0: memory@20000000 {
		device_type = "memory";
		compatible = "mmio-sram";
	};

	soc {
		flash-controller@40022000 {
			compatible = "st,stm32l4-flash-controller";
			label = "FLASH_CTRL";
			reg = <0x40022000 0x400>;
			interrupts = <4 0>;

			#address-cells = <1>;
			#size-cells = <1>;

			flash0: flash@8000000 {
				compatible = "soc-nv-flash";
				label = "FLASH_STM32";

				write-block-size = <8>;
				erase-block-size = <2048>;
			};
		};

		rcc: rcc@40021000 {
			compatible = "st,stm32-rcc";
			clocks-controller;
			#clock-cells = <2>;
			reg = <0x40021000 0x400>;
			label = "STM32_CLK_RCC";
		};

		pinctrl: pin-controller@48000000 {
			compatible = "st,stm32-pinmux";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0x48000000 0x2000>;

			gpioa: gpio@48000000 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000000 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB2 0x00000001>;
				label = "GPIOA";
			};

			gpiob: gpio@48000400 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000400 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB2 0x00000002>;
				label = "GPIOB";
			};

			gpioc: gpio@48000800 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48000800 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB2 0x00000004>;
				label = "GPIOC";
			};

			gpioh: gpio@48001c00 {
				compatible = "st,stm32-gpio";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x48001c00 0x400>;
				clocks = <&rcc STM32_CLOCK_BUS_AHB2 0x00000080>;
				label = "GPIOH";
			};
		};

		idwg: watchdog@40003000 {
			compatible = "st,stm32-watchdog";
			reg = <0x40003000 0x400>;
			label = "IWDG";
			status = "disabled";
		};

		usart1: serial@40013800 {
			compatible = "st,stm32-usart", "st,stm32-uart";
			reg = <0x40013800 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00004000>;
			interrupts = <37 0>;
			status = "disabled";
			label = "UART_1";
		};

		usart2: serial@40004400 {
			compatible = "st,stm32-usart", "st,stm32-uart";
			reg = <0x40004400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00020000>;
			interrupts = <38 0>;
			status = "disabled";
			label = "UART_2";
		};

		lpuart1: serial@40008000 {
			compatible = "st,stm32-lpuart", "st,stm32-uart";
			reg = <0x40008000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1_2 0x00000001>;
			interrupts = <70 0>;
			status = "disabled";
			label = "LPUART_1";
		};

		i2c1: i2c@40005400 {
			compatible = "st,stm32-i2c-v2";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40005400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00200000>;
			interrupts = <31 0>, <32 0>;
			interrupt-names = "event", "error";
			status = "disabled";
			label= "I2C_1";
		};

		i2c3: i2c@40005c00 {
			compatible = "st,stm32-i2c-v2";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40005c00 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00800000>;
			interrupts = <72 0>, <73 0>;
			interrupt-names = "event", "error";
			status = "disabled";
			label= "I2C_3";
		};

		spi1: spi@40013000 {
			compatible = "st,stm32-spi-fifo";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40013000 0x400>;
			interrupts = <35 5>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00001000>;
			status = "disabled";
			label = "SPI_1";
		};


		timers1: timers@40012c00 {
			compatible = "st,stm32-timers";
			reg = <0x40012c00 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00000800>;
			status = "disabled";
			label = "TIMERS_1";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_1";
				#pwm-cells = <2>;
			};
		};

		timers2: timers@40000000 {
			compatible = "st,stm32-timers";
			reg = <0x40000000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000001>;
			status = "disabled";
			label = "TIMERS_2";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <0>;
				label = "PWM_2";
				#pwm-cells = <2>;
			};
		};

		timers6: timers@40001000 {
			compatible = "st,stm32-timers";
			reg = <0x40001000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000010>;
			status = "disabled";
			label = "TIMERS_6";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_6";
				#pwm-cells = <2>;
			};
		};

		timers7: timers@40001400 {
			compatible = "st,stm32-timers";
			reg = <0x40001400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000020>;
			status = "disabled";
			label = "TIMERS_7";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_7";
				#pwm-cells = <2>;
			};
		};

		timers15: timers@40014000 {
			compatible = "st,stm32-timers";
			reg = <0x40014000 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00010000>;
			status = "disabled";
			label = "TIMERS_15";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_15";
				#pwm-cells = <2>;
			};
		};

		timers16: timers@40014400 {
			compatible = "st,stm32-timers";
			reg = <0x40014400 0x400>;
			clocks = <&rcc STM32_CLOCK_BUS_APB2 0x00020000>;
			status = "disabled";
			label = "TIMERS_16";

			pwm {
				compatible = "st,stm32-pwm";
				status = "disabled";
				st,prescaler = <10000>;
				label = "PWM_16";
				#pwm-cells = <2>;
			};
		};

		can1: can@40006400 {
			compatible = "st,stm32-can";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40006400 0x400>;
			interrupts = <19 0>, <20 0>, <21 0>, <22 0>;
			interrupt-names = "TX", "RX0", "RX1", "SCE";
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x02000000>; //RCC_APB1ENR1_CAN1EN
			status = "disabled";
			label = "CAN_1";
			bus-speed = <125000>;
			sjw = <1>;
			prop_seg_phase_seg1 = <4>;
			phase_seg2 = <5>;
		};

		rtc: rtc@40002800 {
			compatible = "st,stm32-rtc";
			reg = <0x40002800 0x400>;
			interrupts = <41 0>;
			clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>;
			prescaler = <32768>;
			status = "disabled";
			label = "RTC_0";
		};
	};
};

&nvic {
	arm,num-irq-priority-bits = <4>;
};