Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 | # Kconfig - BMC150 magnetometer sensor configuration options
#
# Copyright (c) 2016 Intel Corporation
#
# SPDX-License-Identifier: Apache-2.0
#
menuconfig BMC150_MAGN
bool "BMC150_MAGN I2C Magnetometer Chip"
depends on I2C
help
Enable driver for BMC150 I2C-based magnetometer sensor.
if BMC150_MAGN
config BMC150_MAGN_DEV_NAME
string "BMC150_MAGN device name"
default "bmc150_magn"
config BMC150_MAGN_I2C_ADDR
hex "BMC150_MAGN I2C slave address"
default 0x12
help
Specify the I2C slave address for the BMC150_MAGN.
0x12: GND
0x13: VCC
config BMC150_MAGN_I2C_MASTER_DEV_NAME
string "I2C master where BMC150_MAGN is connected"
default "I2C_0"
help
Specify the device name of the I2C master device to which BMC150_MAGN
is connected.
menu "Attributes"
choice
prompt "Default preset"
default BMC150_MAGN_PRESET_REGULAR
help
Specify the default preset (x/y oversampling, z oversampling, sampling
frequency).
config BMC150_MAGN_PRESET_LOW_POWER
bool "Low power (3, 3, 10)"
config BMC150_MAGN_PRESET_REGULAR
bool "Regular (9, 15, 10)"
config BMC150_MAGN_PRESET_ENHANCED_REGULAR
bool "Enhanced regular (15, 27, 10)"
config BMC150_MAGN_PRESET_HIGH_ACCURACY
bool "High accuracy (47, 83, 20)"
endchoice
config BMC150_MAGN_SAMPLING_RATE_RUNTIME
bool "Enable dynamic sampling rate"
help
Enable alteration of sampling rate attribute at runtime.
config BMC150_MAGN_SAMPLING_REP_XY
bool "Enable dynamic XY oversampling"
help
Enable alteration of XY oversampling at runtime.
config BMC150_MAGN_SAMPLING_REP_Z
bool "Enable dynamic Z oversampling"
help
Enable alteration of Z oversampling at runtime.
endmenu
config BMC150_MAGN_TRIGGER
bool "Enable triggers"
depends on GPIO
help
Enable triggers for BMC150 magnetometer
config BMC150_MAGN_TRIGGER_THREAD_STACK
int "Thread stack size"
depends on BMC150_MAGN_TRIGGER
default 1024
help
Specify the internal thread stack size.
config BMC150_MAGN_TRIGGER_DRDY
bool "Enable data ready trigger"
depends on BMC150_MAGN_TRIGGER
help
Enable data ready interrupt for BMC150 magnetometer
config BMC150_MAGN_GPIO_DRDY_DEV_NAME
string "GPIO device where BMC150_MAGN data ready interrupt is connected"
depends on BMC150_MAGN_TRIGGER_DRDY
default "GPIO_0"
help
Specify the device name of the GPIO controller the BMC150_MAGN interrupt
is connected to.
config BMC150_MAGN_GPIO_DRDY_INT_PIN
int "GPIO pin number for the data ready interrupt pin"
default 3
depends on BMC150_MAGN_TRIGGER_DRDY
help
GPIO pin number for the data ready interrupt pin.
endif # BMC150_MAGN
|