Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 | # Kconfig - Quark X1000 SoC configuration options # # Copyright (c) 2014-2015 Wind River Systems, Inc. # Copyright (c) 2015-2016 Intel Corporation # # SPDX-License-Identifier: Apache-2.0 # if SOC_SERIES_QUARK_X1000 config SOC_SERIES default "quark_x1000" config SYS_CLOCK_HW_CYCLES_PER_SEC default 25000000 if HPET_TIMER config CLFLUSH_DETECT default y if CACHE_FLUSHING if SHARED_IRQ config SHARED_IRQ_0 default y endif # SHARED_IRQ if PCI_LEGACY_BRIDGE config PCI_LEGACY_BRIDGE_BUS default 0 config PCI_LEGACY_BRIDGE_DEV default 31 config PCI_LEGACY_BRIDGE_VENDOR_ID default 0x8086 config PCI_LEGACY_BRIDGE_DEVICE_ID default 0x095e endif # PCI_LEGACY_BRIDGE if I2C config I2C_DW default y if I2C_DW config I2C_DW_CLOCK_SPEED default 25 config I2C_0 default y if I2C_0 config I2C_0_IRQ_PRI default 2 endif # I2C_0 endif # I2C_DW endif # I2C if GPIO config GPIO_SCH default y if GPIO_SCH config GPIO_SCH_0 default y config GPIO_SCH_1 default y if GPIO_SCH_0 config GPIO_SCH_0_DEV_NAME default "GPIO_CW" endif # GPIO_SCH_0 if GPIO_SCH_1 config GPIO_SCH_1_DEV_NAME default "GPIO_RW" endif # GPIO_SCH_1 endif # GPIO_SCH config GPIO_DW default y if GPIO_DW config GPIO_DW_0 default y if GPIO_DW_0 config GPIO_DW_0_NAME default "GPIO_0" config GPIO_DW_0_IRQ_PRI default 2 endif # GPIO_DW_0 endif # GPIO_DW endif # GPIO if SPI config SPI_INTEL default y if SPI_INTEL config SPI_0 default y config SPI_1 default n endif # SPI_INTEL endif # SPI if UART_NS16550 config UART_NS16550_PCI default y if PCI config UART_NS16550_PORT_0 default y if UART_NS16550_PORT_0 config UART_NS16550_PORT_0_OPTIONS default 0 config UART_NS16550_PORT_0_PCI default y if UART_NS16550_PCI endif # UART_NS16550_PORT_0 config UART_NS16550_PORT_1 default y if PCI if UART_NS16550_PORT_1 config UART_NS16550_PORT_1_OPTIONS default 0 config UART_NS16550_PORT_1_PCI default y if UART_NS16550_PCI endif # UART_NS16550_PORT_1 endif # UART_NS16550 if NET_L2_ETHERNET config ETH_DW default y if ETH_DW config ETH_DW_0 default y endif # ETH_DW endif # NET_L2_ETHERNET # Pin multiplexer uses PCAL9535A, needs to be initialized after it config PINMUX_INIT_PRIORITY default 80 if PINMUX if UART_CONSOLE endif if BT_UART config BT_UART_ON_DEV_NAME default "UART_1" endif source "soc/x86/intel_quark/quark_x1000/Kconfig.defconfig.quark_x1000" endif # SOC_SERIES_QUARK_X1000 |