Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 | /* * Copyright (c) 2018 Phytec Messtechnik GmbH * Copyright (c) 2017 Linaro Limited * * SPDX-License-Identifier: Apache-2.0 */ /dts-v1/; #include <nordic/nrf52840_qiaa.dtsi> / { model = "reel board"; compatible = "phytec,reel_board", "nordic,nrf52840-qiaa", "nordic,nrf52840"; chosen { zephyr,console = &uart0; zephyr,shell-uart = &uart0; zephyr,uart-mcumgr = &uart0; zephyr,sram = &sram0; zephyr,flash = &flash0; zephyr,code-partition = &slot0_partition; }; leds { compatible = "gpio-leds"; yellow_led: led_0 { gpios = <&gpio0 13 0>; label = "User D13"; }; red_led: led_1 { gpios = <&gpio0 11 0>; label = "User D3 red"; }; green_led: led_2 { gpios = <&gpio0 12 0>; label = "User D3 green"; }; blue_led: led_3 { gpios = <&gpio1 9 0>; label = "User D3 blue"; }; }; gpio_keys { compatible = "gpio-keys"; user_button: button_0 { gpios = <&gpio0 7 GPIO_PUD_PULL_UP>; label = "User Button"; }; }; aliases { led0 = &yellow_led; led1 = &red_led; led2 = &green_led; led3 = &blue_led; sw0 = &user_button; }; }; &gpiote { status ="ok"; }; &gpio0 { status ="ok"; }; &gpio1 { status ="ok"; }; &uart0 { compatible = "nordic,nrf-uart"; current-speed = <115200>; status = "ok"; tx-pin = <6>; rx-pin = <8>; }; &i2c0 { status = "ok"; clock-frequency = <I2C_BITRATE_FAST>; sda-pin = <26>; scl-pin = <27>; mma8652fc@1d { compatible = "nxp,fxos8700","nxp,mma8652fc"; reg = <0x1d>; label = "MMA8652FC"; int1-gpios = <&gpio0 24 0>; int2-gpios = <&gpio0 25 0>; }; hdc1008@43 { compatible = "ti,hdc1008","ti,hdc1010"; reg = <0x43>; label = "HDC1010"; drdy-gpios = <&gpio0 22 GPIO_PUD_PULL_UP>; }; apds9960@39 { compatible = "avago,apds9960"; reg = <0x39>; label = "APDS9960"; int-gpios = <&gpio0 23 0>; }; }; &spi3 { status = "ok"; sck-pin = <19>; mosi-pin = <20>; miso-pin = <21>; cs-gpios = <&gpio0 17 0>; ssd1673fb@0 { compatible = "solomon,ssd1673fb", "gd,gde0213b1"; label = "SSD1673"; spi-max-frequency = <4000000>; reg = <0>; width = <250>; height = <120>; pp-width-bits = <8>; pp-height-bits = <8>; reset-gpios = <&gpio0 15 0>; dc-gpios = <&gpio0 16 0>; busy-gpios = <&gpio0 14 0>; gdv-a = <0x10>; gdv-b = <0x0a>; sdv = <0x19>; vcom = <0xa8>; border-waveform = <0x71>; }; }; &flash0 { /* * For more information, see: * http://docs.zephyrproject.org/latest/guides/dts/index.html#flash-partitions */ partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; boot_partition: partition@0 { label = "mcuboot"; reg = <0x000000000 0x0000C000>; }; slot0_partition: partition@c000 { label = "image-0"; reg = <0x0000C000 0x000067000>; }; slot1_partition: partition@73000 { label = "image-1"; reg = <0x00073000 0x000067000>; }; scratch_partition: partition@da000 { label = "image-scratch"; reg = <0x000da000 0x0001e000>; }; /* * The flash starting at 0x000f8000 and ending at * 0x000fffff is reserved for use by the application. */ /* Storage partition will be used by FCB/NFFS/NVS if enabled. */ storage_partition: partition@f8000 { label = "storage"; reg = <0x000f8000 0x00008000>; }; }; }; &usbd { compatible = "nordic,nrf-usbd"; status = "ok"; }; |