Boot Linux faster!

Check our new training course

Boot Linux faster!

Check our new training course
and Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
# Kconfig - kernel configuration options

#
# Copyright (c) 2014-2015 Wind River Systems, Inc.
#
# SPDX-License-Identifier: Apache-2.0
#


menu "General Kernel Options"

config MULTITHREADING
	bool "Multi-threading"
	default y
	help
	  If disabled, only the main thread is available, so a main() function
	  must be provided. Interrupts are available. Kernel objects will most
	  probably not behave as expected, especially with regards to pending,
	  since the main thread cannot pend, it being the only thread in the
	  system.

	  Many drivers and subsystems will not work with this option; use only
	  when you REALLY know what you are doing.

config NUM_COOP_PRIORITIES
	int "Number of coop priorities" if MULTITHREADING
	default 1 if !MULTITHREADING
	default 16
	range 0 128
	help
	  Number of cooperative priorities configured in the system. Gives access
	  to priorities:

		K_PRIO_COOP(0) to K_PRIO_COOP(CONFIG_NUM_COOP_PRIORITIES - 1)

	  or seen another way, priorities:

		-CONFIG_NUM_COOP_PRIORITIES to -1

	  This can be set to zero to disable cooperative scheduling. Cooperative
	  threads always preempt preemptible threads.

	  Each priority requires an extra 8 bytes of RAM. Each set of 32 extra
	  total priorities require an extra 4 bytes and add one possible
	  iteration to loops that search for the next thread to run.

	  The total number of priorities is

	   NUM_COOP_PRIORITIES + NUM_PREEMPT_PRIORITIES + 1

	  The extra one is for the idle thread, which must run at the lowest
	  priority, and be the only thread at that priority.

config NUM_PREEMPT_PRIORITIES
	int "Number of preemptible priorities" if MULTITHREADING
	default 0 if !MULTITHREADING
	default 15
	range 0 128
	help
	  Number of preemptible priorities available in the system. Gives access
	  to priorities 0 to CONFIG_NUM_PREEMPT_PRIORITIES - 1.

	  This can be set to 0 to disable preemptible scheduling.

	  Each priority requires an extra 8 bytes of RAM. Each set of 32 extra
	  total priorities require an extra 4 bytes and add one possible
	  iteration to loops that search for the next thread to run.

	  The total number of priorities is

	   NUM_COOP_PRIORITIES + NUM_PREEMPT_PRIORITIES + 1

	  The extra one is for the idle thread, which must run at the lowest
	  priority, and be the only thread at that priority.

config MAIN_THREAD_PRIORITY
	int "Priority of initialization/main thread"
	default -2 if !PREEMPT_ENABLED
	default 0
	help
	  Priority at which the initialization thread runs, including the start
	  of the main() function. main() can then change its priority if desired.

config COOP_ENABLED
	def_bool (NUM_COOP_PRIORITIES != 0)

config PREEMPT_ENABLED
	def_bool (NUM_PREEMPT_PRIORITIES != 0)

config PRIORITY_CEILING
	int "Priority inheritance ceiling"
	default 0

config NUM_METAIRQ_PRIORITIES
	int "Number of very-high priority 'preemptor' threads"
	default 0
	help
	 This defines a set of priorities at the (numerically) lowest
	 end of the range which have "meta-irq" behavior.  Runnable
	 threads at these priorities will always be scheduled before
	 threads at lower priorities, EVEN IF those threads are
	 otherwise cooperative and/or have taken a scheduler lock.
	 Making such a thread runnable in any way thus has the effect
	 of "interrupting" the current task and running the meta-irq
	 thread synchronously, like an exception or system call.  The
	 intent is to use these priorities to implement "interrupt
	 bottom half" or "tasklet" behavior, allowing driver
	 subsystems to return from interrupt context but be guaranteed
	 that user code will not be executed (on the current CPU)
	 until the remaining work is finished.  As this breaks the
	 "promise" of non-preemptibility granted by the current API
	 for cooperative threads, this tool probably shouldn't be used
	 from application code.

config SCHED_DEADLINE
	bool "Enable earliest-deadline-first scheduling"
	help
	  This enables a simple "earliest deadline first" scheduling
	  mode where threads can set "deadline" deltas measured in
	  k_cycle_get_32() units.  Priority decisions within (!!) a
	  single priority will choose the next expiring deadline and
	  not simply the least recently added thread.


config MAIN_STACK_SIZE
	int "Size of stack for initialization and main thread"
	default 512 if ZTEST
	default 1024
	help
	  When the initialization is complete, the thread executing it then
	  executes the main() routine, so as to reuse the stack used by the
	  initialization, which would be wasted RAM otherwise.

	  After initialization is complete, the thread runs main().

config IDLE_STACK_SIZE
	int "Size of stack for idle thread"
	default 1024 if XTENSA
	default 512 if RISCV32
	default 320 if ARC || (ARM && CPU_HAS_FPU)
	default 256
	help
	  Depending on the work that the idle task must do, most likely due to
	  power management but possibly to other features like system event
	  logging (e.g. logging when the system goes to sleep), the idle thread
	  may need more stack space than the default value.

config ISR_STACK_SIZE
	int "ISR and initialization stack size (in bytes)"
	default 2048
	help
	  This option specifies the size of the stack used by interrupt
	  service routines (ISRs), and during kernel initialization.

config THREAD_STACK_INFO
	bool "Thread stack info"
	help
	  This option allows each thread to store the thread stack info into
	  the k_thread data structure.

config  THREAD_CUSTOM_DATA
	bool "Thread custom data"
	help
	  This option allows each thread to store 32 bits of custom data,
	  which can be accessed using the k_thread_custom_data_xxx() APIs.

config THREAD_USERSPACE_LOCAL_DATA
	bool
	depends on USERSPACE

config THREAD_USERSPACE_LOCAL_DATA_ARCH_DEFER_SETUP
	bool
	depends on THREAD_USERSPACE_LOCAL_DATA
	default y if ARCH="arc"

config ERRNO
	bool "Enable errno support"
	default y
	select THREAD_USERSPACE_LOCAL_DATA if USERSPACE
	help
	  Enable per-thread errno in the kernel. Application and library code must
	  include errno.h provided by the C library (libc) to use the errno
	  symbol. The C library must access the per-thread errno via the
	  _get_errno() symbol.

config APPLICATION_MEMORY
	bool "Split kernel and application memory"
	help
	  For all read-write memory sections (namely bss, noinit, data),
	  separate them into application and kernel areas. The application area
	  will have the project-level application objects and any libraries
	  including the C library in it.

choice SCHED_ALGORITHM
	prompt "Scheduler priority queue algorithm"
	default SCHED_DUMB
	help
	  The kernel can be built with with several choices for the
	  ready queue implementation, offering different choices between
	  code size, constant factor runtime overhead and performance
	  scaling when many threads are added.

config SCHED_DUMB
	bool "Simple linked-list ready queue"
	help
	  When selected, the scheduler ready queue will be implemented
	  as a simple unordered list, with very fast constant time
	  performance for single threads and very low code size.
	  Choose this on systems with constrained code size that will
	  never see more than a small number (3, maybe) of runnable
	  threads in the queue at any given time.  On most platforms
	  (that are not otherwise using the red/black tree) this
	  results in a savings of ~2k of code size.

config SCHED_SCALABLE
	bool "Red/black tree ready queue"
	help
	  When selected, the scheduler ready queue will be implemented
	  as a red/black tree.  This has rather slower constant-time
	  insertion and removal overhead, and on most platforms (that
	  are not otherwise using the rbtree somewhere) requires an
	  extra ~2kb of code.  But the resulting behavior will scale
	  cleanly and quickly into the many thousands of threads.  Use
	  this on platforms where you may have many threads (very
	  roughly: more than 20 or so) marked as runnable at a given
	  time.  Most applications don't want this.

config SCHED_MULTIQ
	bool "Traditional multi-queue ready queue"
	depends on !SCHED_DEADLINE
	help
	  When selected, the scheduler ready queue will be implemented
	  as the classic/textbook array of lists, one per priority
	  (max 32 priorities).  This corresponds to the scheduler
	  algorithm used in Zephyr versions prior to 1.12.  It incurs
	  only a tiny code size overhead vs. the "dumb" scheduler and
	  runs in O(1) time in almost all circumstances with very low
	  constant factor.  But it requires a fairly large RAM budget
	  to store those list heads, and the limited features make it
	  incompatible with features like deadline scheduling that
	  need to sort threads more finely, and SMP affinity which
	  need to traverse the list of threads.  Typical applications
	  with small numbers of runnable threads probably want the
	  DUMB scheduler.

endchoice # SCHED_ALGORITHM

choice WAITQ_ALGORITHM
	prompt "Wait queue priority algorithm"
	default WAITQ_DUMB
	help
	  The wait_q abstraction used in IPC primitives to pend
	  threads for later wakeup shares the same backend data
	  structure choices as the scheduler, and can use the same
	  options.

config WAITQ_SCALABLE
	bool "Use scalable wait_q implementation"
	help
	  When selected, the wait_q will be implemented with a
	  balanced tree.  Choose this if you expect to have many
	  threads waiting on individual primitives.  There is a ~2kb
	  code size increase over WAITQ_DUMB (which may be shared with
	  SCHED_SCALABLE) if the rbtree is not used elsewhere in the
	  application, and pend/unpend operations on "small" queues
	  will be somewhat slower (though this is not generally a
	  performance path).

config WAITQ_DUMB
	bool "Simple linked-list wait_q"
	help
	  When selected, the wait_q will be implemented with a
	  doubly-linked list.  Choose this if you expect to have only
	  a few threads blocked on any single IPC primitive.

endchoice # WAITQ_ALGORITHM

menu "Kernel Debugging and Metrics"

config INIT_STACKS
	bool "Initialize stack areas"
	help
	  This option instructs the kernel to initialize stack areas with a
	  known value (0xaa) before they are first used, so that the high
	  water mark can be easily determined. This applies to the stack areas
	  for threads.

config KERNEL_DEBUG
	bool "Kernel debugging"
	select INIT_STACKS
	help
	  Enable kernel debugging.

	  Note that debugging the kernel internals can be very verbose.

config BOOT_BANNER
	bool "Boot banner"
	default y
	depends on CONSOLE_HAS_DRIVER
	select PRINTK
	select EARLY_CONSOLE
	help
	  This option outputs a banner to the console device during boot up. It
	  also embeds a date & time stamp in the kernel if the BUILD_TIMESTAMP
	  option is enabled.

config BOOT_DELAY
	int "Boot delay in milliseconds"
	default 0
	help
	  This option delays bootup for the specified amount of
	  milliseconds. This is used to allow serial ports to get ready
	  before starting to print information on them during boot, as
	  some systems might boot to fast for a receiving endpoint to
	  detect the new USB serial bus, enumerate it and get ready to
	  receive before it actually gets data. A similar effect can be
	  achieved by waiting for DCD on the serial port--however, not
	  all serial ports have DCD.

config BUILD_TIMESTAMP
	bool "Build Timestamp"
	help
	  Record a timestamp from the build and add it to the boot banner.
	  Note that this will make the build unreproducible: building
	  Zephyr twice will result in different binaries.

config INT_LATENCY_BENCHMARK
	bool "Interrupt latency metrics [EXPERIMENTAL]"
	depends on ARCH="x86"
	help
	  This option enables the tracking of interrupt latency metrics;
	  the exact set of metrics being tracked is board-dependent.
	  Tracking begins when int_latency_init() is invoked by an application.
	  The metrics are displayed (and a new sampling interval is started)
	  each time int_latency_show() is called thereafter.

config EXECUTION_BENCHMARKING
	bool "Timing metrics"
	help
	  This option enables the tracking of various times inside the kernel
	  the exact set of metrics being tracked is board-dependent.
	  All timing measurements are enabled for X86 and ARM based architectures.
	  In other architectures only a subset are enabled.

config THREAD_MONITOR
	bool "Thread monitoring [EXPERIMENTAL]"
	help
	  This option instructs the kernel to maintain a list of all threads
	  (excluding those that have not yet started or have already
	  terminated).
endmenu

menu "Work Queue Options"
config SYSTEM_WORKQUEUE_STACK_SIZE
	int "System workqueue stack size"
	default 1024

config SYSTEM_WORKQUEUE_PRIORITY
	int "System workqueue priority"
	default -2 if COOP_ENABLED && !PREEMPT_ENABLED
	default  0 if !COOP_ENABLED
	default -1
	help
	  By default, system work queue priority is the lowest cooperative
	  priority. This means that any work handler, once started, won't
	  be preempted by any other thread until finished.

config OFFLOAD_WORKQUEUE_STACK_SIZE
	int "Workqueue stack size for thread offload requests"
	default 1024

config OFFLOAD_WORKQUEUE_PRIORITY
	int "Offload requests workqueue priority"
	default -1

endmenu

menu "Atomic Operations"
config ATOMIC_OPERATIONS_BUILTIN
	bool
	help
	  Use the compiler builtin functions for atomic operations. This is
	  the preferred method. However, support for all arches in GCC is
	  incomplete.

config ATOMIC_OPERATIONS_CUSTOM
	bool
	help
	  Use when there isn't support for compiler built-ins, but you have
	  written optimized assembly code under arch/ which implements these.

config ATOMIC_OPERATIONS_C
	bool
	help
	  Use atomic operations routines that are implemented entirely
	  in C by locking interrupts. Selected by architectures which either
	  do not have support for atomic operations in their instruction
	  set, or haven't been implemented yet during bring-up, and also
	  the compiler does not have support for the atomic __sync_* builtins.
endmenu

menu "Timer API Options"

config TIMESLICING
	bool "Thread time slicing"
	default y
	depends on SYS_CLOCK_EXISTS && (NUM_PREEMPT_PRIORITIES != 0)
	help
	  This option enables time slicing between preemptible threads of
	  equal priority.

config TIMESLICE_SIZE
	int "Time slice size (in ms)"
	default 0
	range 0 2147483647
	depends on TIMESLICING
	help
	  This option specifies the maximum amount of time a thread can execute
	  before other threads of equal priority are given an opportunity to run.
	  A time slice size of zero means "no limit" (i.e. an infinitely large
	  time slice).

config TIMESLICE_PRIORITY
	int "Time slicing thread priority ceiling"
	default 0
	range 0 NUM_PREEMPT_PRIORITIES
	depends on TIMESLICING
	help
	  This option specifies the thread priority level at which time slicing
	  takes effect; threads having a higher priority than this ceiling are
	  not subject to time slicing.

config POLL
	bool "Async I/O Framework"
	help
	  Asynchronous notification framework. Enable the k_poll() and
	  k_poll_signal() APIs.  The former can wait on multiple events
	  concurrently, which can be either directly triggered or triggered by
	  the availability of some kernel objects (semaphores and fifos).

endmenu

menu "Other Kernel Object Options"

config NUM_MBOX_ASYNC_MSGS
	int "Maximum number of in-flight asynchronous mailbox messages"
	default 10
	help
	  This option specifies the total number of asynchronous mailbox
	  messages that can exist simultaneously, across all mailboxes
	  in the system.

	  Setting this option to 0 disables support for asynchronous
	  mailbox messages.

config NUM_PIPE_ASYNC_MSGS
	int "Maximum number of in-flight asynchronous pipe messages"
	default 10
	help
	  This option specifies the total number of asynchronous pipe
	  messages that can exist simultaneously, across all pipes in
	  the system.

	  Setting this option to 0 disables support for asynchronous
	  pipe messages.

config HEAP_MEM_POOL_SIZE
	int "Heap memory pool size (in bytes)"
	default 0 if !POSIX_MQUEUE
	default 1024 if POSIX_MQUEUE
	help
	  This option specifies the size of the heap memory pool used when
	  dynamically allocating memory using k_malloc(). Supported values
	  are: 256, 1024, 4096, and 16384. A size of zero means that no
	  heap memory pool is defined.
endmenu

config ARCH_HAS_CUSTOM_SWAP_TO_MAIN
	bool
	# hidden
	help
	  It's possible that an architecture port cannot use _Swap() to swap to
	  the _main() thread, but instead must do something custom. It must
	  enable this option in that case.

config ARCH_HAS_CUSTOM_BUSY_WAIT
	bool
	# hidden
	help
	  It's possible that an architecture port cannot or does not want to use
	  the provided k_busy_wait(), but instead must do something custom. It must
	  enable this option in that case.

config SYS_CLOCK_TICKS_PER_SEC
	int "System tick frequency (in ticks/second)"
	default 100
	help
	  This option specifies the frequency of the system clock in Hz.

	  Depending on the choice made, an amount of possibly expensive math must
	  occur when converting ticks to milliseconds and vice-versa. Some values
	  are optimized, and yield significantly less math.

	  The optimal values from a computational point-of-view are 1000, 500,
	  250 and 125, since in these cases there is either no computation
	  required, or it is all done via bit-shifting. These also give a
	  granularity from 1ms to 8ms.

	  Other good values are 100, 50, 25, 20 and 10. In this case, some math
	  is required but is minimized. These are also values that necessitate a
	  reduced number of clock interrupts per second, at the cost of
	  granularity (10ms to 100ms).

	  All other values require some extensive 64-bit math, and in some
	  configurations even require calls to compiler built-in functions, and
	  can require a non-trivial extra amount of stack space (e.g. around 80
	  bytes on x86).

config SYS_CLOCK_HW_CYCLES_PER_SEC
	int "System clock's h/w timer frequency"
	help
	  This option specifies the frequency of the hardware timer used for the
	  system clock (in Hz). This option is set by the SOC's or board's Kconfig file
	  and the user should generally avoid modifying it via the menu configuration.

config SYS_CLOCK_EXISTS
	def_bool (SYS_CLOCK_TICKS_PER_SEC != 0)
	# omit prompt to signify a "hidden" option
	help
	  This option specifies that the kernel lacks timer support.

config XIP
	bool "Execute in place"
	help
	  This option allows the kernel to operate with its text and read-only
	  sections residing in ROM (or similar read-only memory). Not all boards
	  support this option so it must be used with care; you must also
	  supply a linker command file when building your image. Enabling this
	  option increases both the code and data footprint of the image.

menu "Initialization Priorities"

config KERNEL_INIT_PRIORITY_OBJECTS
	int "Kernel objects initialization priority"
	default 30
	help
	  Kernel objects use this priority for initialization. This
	  priority needs to be higher than minimal default initialization
	  priority.

config KERNEL_INIT_PRIORITY_DEFAULT
	int "Default init priority"
	default 40
	help
	  Default minimal init priority for each init level.

config KERNEL_INIT_PRIORITY_DEVICE
	int "Default init priority for device drivers"
	default 50
	help
	  Device driver, that depends on common components, such as
	  interrupt controller, but does not depend on other devices,
	  uses this init priority.

config APPLICATION_INIT_PRIORITY
	int "Default init priority for application level drivers"
	default 90
	help
	  This priority level is for end-user drivers such as sensors and display
	  which have no inward dependencies.


endmenu

menu "Security Options"

config RETPOLINE
	bool "Build with retpolines enabled"
	default y if !X86_NO_SPECTRE_V2
	help
	  This is recommended on platforms with speculative executions, to protect
	  against branch target injection (AKA Spectre-V2).  Full description of
	  how retpolines work can be found here[1].

	  Currently only the x86 port

	  [1] https://support.google.com/faqs/answer/7625886

config STACK_CANARIES
	bool "Compiler stack canaries"
	help
	  This option enables compiler stack canaries support kernel functions.

	  If stack canaries are supported by the compiler, it will emit
	  extra code that inserts a canary value into the stack frame when
	  a function is entered and validates this value upon exit.
	  Stack corruption (such as that caused by buffer overflow) results
	  in a fatal error condition for the running entity.
	  Enabling this option can result in a significant increase
	  in footprint and an associated decrease in performance.

	  If stack canaries are not supported by the compiler, enabling this
	  option has no effect.

config EXECUTE_XOR_WRITE
	bool "Enable W^X for memory partitions"
	depends on USERSPACE
	depends on ARCH_HAS_EXECUTABLE_PAGE_BIT
	default y
	help
	  When enabled, will enforce that a writable page isn't executable
	  and vice versa.  This might not be acceptable in all scenarios,
	  so this option is given for those unafraid of shooting themselves
	  in the foot.

	  If unsure, say Y.

config STACK_POINTER_RANDOM
	int "Initial stack pointer randomization bounds"
	depends on !STACK_GROWS_UP
	default 0
	help
	  This option performs a limited form of Address Space Layout
	  Randomization by offsetting some random value to a thread's
	  initial stack pointer upon creation. This hinders some types of
	  security attacks by making the location of any given stack frame
	  non-deterministic.

	  This feature can waste up to the specified size in bytes the stack
	  region, which is carved out of the total size of the stack region.
	  A reasonable minimum value would be around 100 bytes if this can
	  be spared.

	  This is currently only implemented for systems whose stack pointers
	  grow towards lower memory addresses.

endmenu

config MAX_DOMAIN_PARTITIONS
	int "Maximum number of partitions per memory domain"
	default 16
	range 0 255
	depends on USERSPACE
	help
	  Configure the maximum number of partitions per memory domain.

menu "SMP Options"
config USE_SWITCH
	bool "Use new-style _arch_switch instead of __swap"
	help
	  The _arch_switch() API is a lower level context switching
	  primitive than the original __swap mechanism.  It is required
	  for an SMP-aware scheduler, or if the architecture does not
	  provide __swap.  In uniprocess situations where the
	  architecture provides both, _arch_switch incurs more somewhat
	  overhead and may be slower.

config SMP
	bool "Enable symmetric multithreading support"
	help
	  When true, kernel will be built with SMP support, allowing
	  more than one CPU to schedule Zephyr tasks at a time.

config MP_NUM_CPUS
	int "Number of CPUs/cores"
	default 1
	help
	  Number of multiprocessing-capable cores available to the
	  multicpu API and SMP features.

endmenu

source "kernel/Kconfig.power_mgmt"

endmenu