Linux preempt-rt

Check our new training course

Real-Time Linux with PREEMPT_RT

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

.. _sam_e70_xplained:

SAM E70 Xplained


The SAM E70 Xplained evaluation kit is a development platform to evaluate the
Atmel SAM E70 series microcontrollers.

.. image:: img/sam_e70_xplained.png
     :width: 500px
     :align: center
     :alt: SAM E70 Xplained


- ATSAME70Q21 ARM Cortex-M7 Processor
- 12 MHz crystal oscillator
- 32.768 kHz crystal oscillator (not populated)
- IS42S16100E 16 Mb SDRAM
- SD card connector
- Ethernet port
- Micro-AB USB device
- Micro-AB USB debug interface supporting CMSIS-DAP, Virtual COM Port and Data
  Gateway Interface (DGI)
- JTAG interface connector
- One reset and one user pushbutton
- One green user LED

Supported Features

The sam_e70_xplained board configuration supports the following hardware

| Interface | Controller | Driver/Component                    |
| NVIC      | on-chip    | nested vector interrupt controller  |
| SYSTICK   | on-chip    | systick                             |
| UART      | on-chip    | serial port                         |
| USART     | on-chip    | serial port                         |
| I2C       | on-chip    | i2c                                 |
| ETHERNET  | on-chip    | ethernet                            |
| WATCHDOG  | on-chip    | watchdog                            |

Other hardware features are not currently supported by Zephyr.

The default configuration can be found in the Kconfig

Connections and IOs

The `SAME70-XPLD User Guide`_ has detailed information about board connections.

System Clock

The SAM E70 MCU is configured to use the 12 MHz external oscillator on the board
with the on-chip PLL to generate a 300 MHz system clock.

Serial Port

The ATSAME70Q21 MCU has five UARTs and three USARTs. One of the USARTs is
configured for the console and is available as a Virtual COM Port via EDBG USB

Programming and Debugging

Flashing the Zephyr project onto SAM E70 MCU requires the `OpenOCD tool`_.
Support for Atmel SAM E microcontroller series was added in OpenOCD release
0.10.0, which was added in Zephyr SDK 0.9.2.

By default a factory new SAM E70 chip will boot SAM-BA boot loader located in
the ROM, not the flashed image. This is determined by the value of GPNVM1
(General-Purpose NVM bit 1). The flash procedure will ensure that GPNVM1 is
set to 1 changing the default behavior to boot from Flash.

If your chip has a security bit GPNVM0 set you will be unable to program flash
memory or connect to it via a debug interface. The only way to clear GPNVM0
is to perform a chip erase procedure that will erase all GPNVM bits and the full
contents of the SAM E70 flash memory:

- With the board power off, set a jumper on the J200 header.
- Turn the board power on. The jumper can be removed soon after the power is on
  (flash erasing procedure is started when the erase line is asserted for at
  least 230ms)


#. Run your favorite terminal program to listen for output. Under Linux the
   terminal should be :code:`/dev/ttyACM0`. For example:

   .. code-block:: console

      $ minicom -D /dev/ttyACM0 -o

   The -o option tells minicom not to send the modem initialization
   string. Connection should be configured as follows:

   - Speed: 115200
   - Data: 8 bits
   - Parity: None
   - Stop bits: 1

#. Connect the SAM E70 Xplained board to your host computer using the
   USB debug port. Then build and flash the :ref:`hello_world`

   .. zephyr-app-commands::
      :zephyr-app: samples/hello_world
      :board: sam_e70_xplained
      :goals: build flash

   You should see "Hello World!" in your terminal.

You can flash the image using an external debug adapter such as J-Link
or ULINK, connected to the 20-pin JTAG header. Supply the name of the
debug adapter (e.g., ``jlink``) via an OPENOCD_INTERFACE environment
variable. OpenOCD will look for the appropriate interface
configuration in an ``interface/$(OPENOCD_INTERFACE).cfg`` file on its
internal search path.


You can debug an application in the usual way.  Here is an example for the
:ref:`hello_world` application.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: sam_e70_xplained
   :goals: debug


SAM E70 Product Page:

.. _SAME70-XPLD User Guide:

.. _OpenOCD tool:

.. _SAM-BA: