Linux debugging

Check our new training course

Linux debugging, tracing, profiling & perf. analysis

Check our new training course
with Creative Commons CC-BY-SA
lecture and lab materials

Bootlin logo

Elixir Cross Referencer

Analog Devices AD5592R/AD5593R DAC/ADC device driver

Required properties for the AD5592R:
	- compatible: Must be "adi,ad5592r"
	- reg: SPI chip select number for the device
	- spi-max-frequency: Max SPI frequency to use (< 30000000)
	- spi-cpol: The AD5592R requires inverse clock polarity (CPOL) mode

Required properties for the AD5593R:
	- compatible: Must be "adi,ad5593r"
	- reg: I2C address of the device

Required properties for all supported chips:
	- #address-cells: Should be 1.
	- #size-cells: Should be 0.
	- channel nodes:
	  Each child node represents one channel and has the following
	  Required properties:
		* reg: Pin on which this channel is connected to.
		* adi,mode: Mode or function of this channel.
			    Macros specifying the valid values
			    can be found in <dt-bindings/iio/adi,ad5592r.h>.

			    The following values are currently supported:
				* CH_MODE_UNUSED (the pin is unused)
				* CH_MODE_ADC (the pin is ADC input)
				* CH_MODE_DAC (the pin is DAC output)
				* CH_MODE_DAC_AND_ADC (the pin is DAC output
					but can be monitored by an ADC, since
					there is no disadvantage this
					this should be considered as the
					preferred DAC mode)
				* CH_MODE_GPIO (the pin is registered
					with GPIOLIB)
	 Optional properties:
		* adi,off-state: State of this channel when unused or the
				 device gets removed. Macros specifying the
				 valid values can be found in
				 <dt-bindings/iio/adi,ad5592r.h>.

				* CH_OFFSTATE_PULLDOWN (the pin is pulled down)
				* CH_OFFSTATE_OUT_LOW  (the pin is output low)
				* CH_OFFSTATE_OUT_HIGH (the pin is output high)
				* CH_OFFSTATE_OUT_TRISTATE (the pin is
					tristated output)


Optional properties:
	- vref-supply: Phandle to the external reference voltage supply. This should
	  only be set if there is an external reference voltage connected to the VREF
	  pin. If the property is not set the internal 2.5V reference is used.
	- reset-gpios : GPIO spec for the RESET pin. If specified, it will be
	  asserted during driver probe.
	- gpio-controller: Marks the device node as a GPIO controller.
	- #gpio-cells: Should be 2. The first cell is the GPIO number and the second
	  cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.

AD5592R Example:

	#include <dt-bindings/iio/adi,ad5592r.h>

	vref: regulator-vref {
		compatible = "regulator-fixed";
		regulator-name = "vref-ad559x";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-always-on;
	};

	ad5592r@0 {
		#size-cells = <0>;
		#address-cells = <1>;
		#gpio-cells = <2>;
		compatible = "adi,ad5592r";
		reg = <0>;

		spi-max-frequency = <1000000>;
		spi-cpol;

		vref-supply = <&vref>; /* optional */
		reset-gpios = <&gpio0 86 0>;  /* optional */
		gpio-controller;

		channel@0 {
			reg = <0>;
			adi,mode = <CH_MODE_DAC>;
		};
		channel@1 {
			reg = <1>;
			adi,mode = <CH_MODE_ADC>;
		};
		channel@2 {
			reg = <2>;
			adi,mode = <CH_MODE_DAC_AND_ADC>;
		};
		channel@3 {
			reg = <3>;
			adi,mode = <CH_MODE_DAC_AND_ADC>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@4 {
			reg = <4>;
			adi,mode = <CH_MODE_UNUSED>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@5 {
			reg = <5>;
			adi,mode = <CH_MODE_GPIO>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@6 {
			reg = <6>;
			adi,mode = <CH_MODE_GPIO>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@7 {
			reg = <7>;
			adi,mode = <CH_MODE_GPIO>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
	};

AD5593R Example:

	#include <dt-bindings/iio/adi,ad5592r.h>

	ad5593r@10 {
		#size-cells = <0>;
		#address-cells = <1>;
		#gpio-cells = <2>;
		compatible = "adi,ad5593r";
		reg = <0x10>;
		gpio-controller;

		channel@0 {
			reg = <0>;
			adi,mode = <CH_MODE_DAC>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@1 {
			reg = <1>;
			adi,mode = <CH_MODE_ADC>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@2 {
			reg = <2>;
			adi,mode = <CH_MODE_DAC_AND_ADC>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
		channel@6 {
			reg = <6>;
			adi,mode = <CH_MODE_GPIO>;
			adi,off-state = <CH_OFFSTATE_PULLDOWN>;
		};
	};