Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 | /*
* Asm versions of Xen pv-ops, suitable for either direct use or
* inlining. The inline versions are the same as the direct-use
* versions, with the pre- and post-amble chopped off.
*
* This code is encoded for size rather than absolute efficiency, with
* a view to being able to inline as much as possible.
*
* We only bother with direct forms (ie, vcpu in percpu data) of the
* operations here; the indirect forms are better handled in C, since
* they're generally too large to inline anyway.
*/
#include <asm/asm-offsets.h>
#include <asm/percpu.h>
#include <asm/processor-flags.h>
#include "xen-asm.h"
/*
* Enable events. This clears the event mask and tests the pending
* event status with one and operation. If there are pending events,
* then enter the hypervisor to get them handled.
*/
ENTRY(xen_irq_enable_direct)
/* Unmask events */
movb $0, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
/*
* Preempt here doesn't matter because that will deal with any
* pending interrupts. The pending check may end up being run
* on the wrong CPU, but that doesn't hurt.
*/
/* Test for pending */
testb $0xff, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_pending
jz 1f
2: call check_events
1:
ENDPATCH(xen_irq_enable_direct)
ret
ENDPROC(xen_irq_enable_direct)
RELOC(xen_irq_enable_direct, 2b+1)
/*
* Disabling events is simply a matter of making the event mask
* non-zero.
*/
ENTRY(xen_irq_disable_direct)
movb $1, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
ENDPATCH(xen_irq_disable_direct)
ret
ENDPROC(xen_irq_disable_direct)
RELOC(xen_irq_disable_direct, 0)
/*
* (xen_)save_fl is used to get the current interrupt enable status.
* Callers expect the status to be in X86_EFLAGS_IF, and other bits
* may be set in the return value. We take advantage of this by
* making sure that X86_EFLAGS_IF has the right value (and other bits
* in that byte are 0), but other bits in the return value are
* undefined. We need to toggle the state of the bit, because Xen and
* x86 use opposite senses (mask vs enable).
*/
ENTRY(xen_save_fl_direct)
testb $0xff, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
setz %ah
addb %ah, %ah
ENDPATCH(xen_save_fl_direct)
ret
ENDPROC(xen_save_fl_direct)
RELOC(xen_save_fl_direct, 0)
/*
* In principle the caller should be passing us a value return from
* xen_save_fl_direct, but for robustness sake we test only the
* X86_EFLAGS_IF flag rather than the whole byte. After setting the
* interrupt mask state, it checks for unmasked pending events and
* enters the hypervisor to get them delivered if so.
*/
ENTRY(xen_restore_fl_direct)
#ifdef CONFIG_X86_64
testw $X86_EFLAGS_IF, %di
#else
testb $X86_EFLAGS_IF>>8, %ah
#endif
setz PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_mask
/*
* Preempt here doesn't matter because that will deal with any
* pending interrupts. The pending check may end up being run
* on the wrong CPU, but that doesn't hurt.
*/
/* check for unmasked and pending */
cmpw $0x0001, PER_CPU_VAR(xen_vcpu_info) + XEN_vcpu_info_pending
jnz 1f
2: call check_events
1:
ENDPATCH(xen_restore_fl_direct)
ret
ENDPROC(xen_restore_fl_direct)
RELOC(xen_restore_fl_direct, 2b+1)
/*
* Force an event check by making a hypercall, but preserve regs
* before making the call.
*/
check_events:
#ifdef CONFIG_X86_32
push %eax
push %ecx
push %edx
call xen_force_evtchn_callback
pop %edx
pop %ecx
pop %eax
#else
push %rax
push %rcx
push %rdx
push %rsi
push %rdi
push %r8
push %r9
push %r10
push %r11
call xen_force_evtchn_callback
pop %r11
pop %r10
pop %r9
pop %r8
pop %rdi
pop %rsi
pop %rdx
pop %rcx
pop %rax
#endif
ret
|