Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 | /* linux/arch/arm/mach-exynos4/platsmp.c
*
* Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
* Cloned from linux/arch/arm/mach-vexpress/platsmp.c
*
* Copyright (C) 2002 ARM Ltd.
* All Rights Reserved
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/jiffies.h>
#include <linux/smp.h>
#include <linux/io.h>
#include <asm/cacheflush.h>
#include <asm/smp_plat.h>
#include <asm/smp_scu.h>
#include <asm/firmware.h>
#include <mach/hardware.h>
#include <mach/regs-clock.h>
#include <mach/regs-pmu.h>
#include <plat/cpu.h>
#include "common.h"
extern void exynos4_secondary_startup(void);
static inline void __iomem *cpu_boot_reg_base(void)
{
if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1)
return S5P_INFORM5;
return S5P_VA_SYSRAM;
}
static inline void __iomem *cpu_boot_reg(int cpu)
{
void __iomem *boot_reg;
boot_reg = cpu_boot_reg_base();
if (soc_is_exynos4412())
boot_reg += 4*cpu;
else if (soc_is_exynos5420())
boot_reg += 4;
return boot_reg;
}
/*
* Write pen_release in a way that is guaranteed to be visible to all
* observers, irrespective of whether they're taking part in coherency
* or not. This is necessary for the hotplug code to work reliably.
*/
static void write_pen_release(int val)
{
pen_release = val;
smp_wmb();
__cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release));
outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1));
}
static void __iomem *scu_base_addr(void)
{
return (void __iomem *)(S5P_VA_SCU);
}
static DEFINE_SPINLOCK(boot_lock);
static void exynos_secondary_init(unsigned int cpu)
{
/*
* let the primary processor know we're out of the
* pen, then head off into the C entry point
*/
write_pen_release(-1);
/*
* Synchronise with the boot thread.
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
unsigned long phys_cpu = cpu_logical_map(cpu);
/*
* Set synchronisation state between this boot processor
* and the secondary one
*/
spin_lock(&boot_lock);
/*
* The secondary processor is waiting to be released from
* the holding pen - release it, then wait for it to flag
* that it has been released by resetting pen_release.
*
* Note that "pen_release" is the hardware CPU ID, whereas
* "cpu" is Linux's internal ID.
*/
write_pen_release(phys_cpu);
if (!(__raw_readl(S5P_ARM_CORE1_STATUS) & S5P_CORE_LOCAL_PWR_EN)) {
__raw_writel(S5P_CORE_LOCAL_PWR_EN,
S5P_ARM_CORE1_CONFIGURATION);
timeout = 10;
/* wait max 10 ms until cpu1 is on */
while ((__raw_readl(S5P_ARM_CORE1_STATUS)
& S5P_CORE_LOCAL_PWR_EN) != S5P_CORE_LOCAL_PWR_EN) {
if (timeout-- == 0)
break;
mdelay(1);
}
if (timeout == 0) {
printk(KERN_ERR "cpu1 power enable failed");
spin_unlock(&boot_lock);
return -ETIMEDOUT;
}
}
/*
* Send the secondary CPU a soft interrupt, thereby causing
* the boot monitor to read the system wide flags register,
* and branch to the address found there.
*/
timeout = jiffies + (1 * HZ);
while (time_before(jiffies, timeout)) {
unsigned long boot_addr;
smp_rmb();
boot_addr = virt_to_phys(exynos4_secondary_startup);
/*
* Try to set boot address using firmware first
* and fall back to boot register if it fails.
*/
if (call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr))
__raw_writel(boot_addr, cpu_boot_reg(phys_cpu));
call_firmware_op(cpu_boot, phys_cpu);
arch_send_wakeup_ipi_mask(cpumask_of(cpu));
if (pen_release == -1)
break;
udelay(10);
}
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
*/
spin_unlock(&boot_lock);
return pen_release != -1 ? -ENOSYS : 0;
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
static void __init exynos_smp_init_cpus(void)
{
void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
else
/*
* CPU Nodes are passed thru DT and set_cpu_possible
* is set by "arm_dt_init_cpu_maps".
*/
return;
/* sanity check */
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
}
static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
{
int i;
if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
scu_enable(scu_base_addr());
/*
* Write the address of secondary startup into the
* system-wide flags register. The boot monitor waits
* until it receives a soft interrupt, and then the
* secondary CPU branches to this address.
*
* Try using firmware operation first and fall back to
* boot register if it fails.
*/
for (i = 1; i < max_cpus; ++i) {
unsigned long phys_cpu;
unsigned long boot_addr;
phys_cpu = cpu_logical_map(i);
boot_addr = virt_to_phys(exynos4_secondary_startup);
if (call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr))
__raw_writel(boot_addr, cpu_boot_reg(phys_cpu));
}
}
struct smp_operations exynos_smp_ops __initdata = {
.smp_init_cpus = exynos_smp_init_cpus,
.smp_prepare_cpus = exynos_smp_prepare_cpus,
.smp_secondary_init = exynos_secondary_init,
.smp_boot_secondary = exynos_boot_secondary,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_die = exynos_cpu_die,
#endif
};
|