Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 | /*
* linux/arch/arm/mach-at91/board-rm9200ek.c
*
* Copyright (C) 2005 SAN People
*
* Epson S1D framebuffer glue code is:
* Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/hardware.h>
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
#include "at91_aic.h"
#include "board.h"
#include "generic.h"
static void __init ek_init_early(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
}
static struct macb_platform_data __initdata ek_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PD4,
.pullup_pin = AT91_PIN_PD5,
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct mci_platform_data __initdata ek_mci0_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PB27,
.wp_pin = AT91_PIN_PA17,
}
};
#endif
static struct spi_board_info ek_spi_devices[] = {
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
},
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 3,
.max_speed_hz = 15 * 1000 * 1000,
},
#endif
};
static struct i2c_board_info __initdata ek_i2c_devices[] = {
{
I2C_BOARD_INFO("ics1523", 0x26),
},
{
I2C_BOARD_INFO("dac3550", 0x4d),
}
};
#define EK_FLASH_BASE AT91_CHIPSELECT_0
#define EK_FLASH_SIZE SZ_8M
static struct physmap_flash_data ek_flash_data = {
.width = 2,
};
static struct resource ek_flash_resource = {
.start = EK_FLASH_BASE,
.end = EK_FLASH_BASE + EK_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device ek_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &ek_flash_data,
},
.resource = &ek_flash_resource,
.num_resources = 1,
};
static struct gpio_led ek_leds[] = {
{ /* "user led 1", DS2 */
.name = "green",
.gpio = AT91_PIN_PB0,
.active_low = 1,
.default_trigger = "mmc0",
},
{ /* "user led 2", DS4 */
.name = "yellow",
.gpio = AT91_PIN_PB1,
.active_low = 1,
.default_trigger = "heartbeat",
},
{ /* "user led 3", DS6 */
.name = "red",
.gpio = AT91_PIN_PB2,
.active_low = 1,
}
};
static void __init ek_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&ek_eth_data);
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mci(0, &ek_mci0_data);
#endif
/* NOR Flash */
platform_device_register(&ek_flash);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* VGA */
// ek_add_device_video();
}
MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
/* Maintainer: SAN People/Atmel */
.init_time = at91rm9200_timer_init,
.map_io = at91_map_io,
.handle_irq = at91_aic_handle_irq,
.init_early = ek_init_early,
.init_irq = at91_init_irq_default,
.init_machine = ek_board_init,
MACHINE_END
|