/*
 * linux/arch/arm/mach-sa1100/neponset.c
 *
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/slab.h>

#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/serial_sa1100.h>
#include <mach/assabet.h>
#include <mach/neponset.h>
#include <asm/hardware/sa1111.h>
#include <asm/sizes.h>

/*
 * Install handler for Neponset IRQ.  Note that we have to loop here
 * since the ETHERNET and USAR IRQs are level based, and we need to
 * ensure that the IRQ signal is deasserted before returning.  This
 * is rather unfortunate.
 */
static void
neponset_irq_handler(unsigned int irq, struct irq_desc *desc)
{
	unsigned int irr;

	while (1) {
		struct irq_desc *d;

		/*
		 * Acknowledge the parent IRQ.
		 */
		desc->chip->ack(irq);

		/*
		 * Read the interrupt reason register.  Let's have all
		 * active IRQ bits high.  Note: there is a typo in the
		 * Neponset user's guide for the SA1111 IRR level.
		 */
		irr = IRR ^ (IRR_ETHERNET | IRR_USAR);

		if ((irr & (IRR_ETHERNET | IRR_USAR | IRR_SA1111)) == 0)
			break;

		/*
		 * Since there is no individual mask, we have to
		 * mask the parent IRQ.  This is safe, since we'll
		 * recheck the register for any pending IRQs.
		 */
		if (irr & (IRR_ETHERNET | IRR_USAR)) {
			desc->chip->mask(irq);

			/*
			 * Ack the interrupt now to prevent re-entering
			 * this neponset handler.  Again, this is safe
			 * since we'll check the IRR register prior to
			 * leaving.
			 */
			desc->chip->ack(irq);

			if (irr & IRR_ETHERNET) {
				d = irq_desc + IRQ_NEPONSET_SMC9196;
				desc_handle_irq(IRQ_NEPONSET_SMC9196, d);
			}

			if (irr & IRR_USAR) {
				d = irq_desc + IRQ_NEPONSET_USAR;
				desc_handle_irq(IRQ_NEPONSET_USAR, d);
			}

			desc->chip->unmask(irq);
		}

		if (irr & IRR_SA1111) {
			d = irq_desc + IRQ_NEPONSET_SA1111;
			desc_handle_irq(IRQ_NEPONSET_SA1111, d);
		}
	}
}

static void neponset_set_mctrl(struct uart_port *port, u_int mctrl)
{
	u_int mdm_ctl0 = MDM_CTL_0;

	if (port->mapbase == _Ser1UTCR0) {
		if (mctrl & TIOCM_RTS)
			mdm_ctl0 &= ~MDM_CTL0_RTS2;
		else
			mdm_ctl0 |= MDM_CTL0_RTS2;

		if (mctrl & TIOCM_DTR)
			mdm_ctl0 &= ~MDM_CTL0_DTR2;
		else
			mdm_ctl0 |= MDM_CTL0_DTR2;
	} else if (port->mapbase == _Ser3UTCR0) {
		if (mctrl & TIOCM_RTS)
			mdm_ctl0 &= ~MDM_CTL0_RTS1;
		else
			mdm_ctl0 |= MDM_CTL0_RTS1;

		if (mctrl & TIOCM_DTR)
			mdm_ctl0 &= ~MDM_CTL0_DTR1;
		else
			mdm_ctl0 |= MDM_CTL0_DTR1;
	}

	MDM_CTL_0 = mdm_ctl0;
}

static u_int neponset_get_mctrl(struct uart_port *port)
{
	u_int ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR;
	u_int mdm_ctl1 = MDM_CTL_1;

	if (port->mapbase == _Ser1UTCR0) {
		if (mdm_ctl1 & MDM_CTL1_DCD2)
			ret &= ~TIOCM_CD;
		if (mdm_ctl1 & MDM_CTL1_CTS2)
			ret &= ~TIOCM_CTS;
		if (mdm_ctl1 & MDM_CTL1_DSR2)
			ret &= ~TIOCM_DSR;
	} else if (port->mapbase == _Ser3UTCR0) {
		if (mdm_ctl1 & MDM_CTL1_DCD1)
			ret &= ~TIOCM_CD;
		if (mdm_ctl1 & MDM_CTL1_CTS1)
			ret &= ~TIOCM_CTS;
		if (mdm_ctl1 & MDM_CTL1_DSR1)
			ret &= ~TIOCM_DSR;
	}

	return ret;
}

static struct sa1100_port_fns neponset_port_fns __devinitdata = {
	.set_mctrl	= neponset_set_mctrl,
	.get_mctrl	= neponset_get_mctrl,
};

static int __devinit neponset_probe(struct platform_device *dev)
{
	sa1100_register_uart_fns(&neponset_port_fns);

	/*
	 * Install handler for GPIO25.
	 */
	set_irq_type(IRQ_GPIO25, IRQ_TYPE_EDGE_RISING);
	set_irq_chained_handler(IRQ_GPIO25, neponset_irq_handler);

	/*
	 * We would set IRQ_GPIO25 to be a wake-up IRQ, but
	 * unfortunately something on the Neponset activates
	 * this IRQ on sleep (ethernet?)
	 */
#if 0
	enable_irq_wake(IRQ_GPIO25);
#endif

	/*
	 * Setup other Neponset IRQs.  SA1111 will be done by the
	 * generic SA1111 code.
	 */
	set_irq_handler(IRQ_NEPONSET_SMC9196, handle_simple_irq);
	set_irq_flags(IRQ_NEPONSET_SMC9196, IRQF_VALID | IRQF_PROBE);
	set_irq_handler(IRQ_NEPONSET_USAR, handle_simple_irq);
	set_irq_flags(IRQ_NEPONSET_USAR, IRQF_VALID | IRQF_PROBE);

	/*
	 * Disable GPIO 0/1 drivers so the buttons work on the module.
	 */
	NCR_0 = NCR_GP01_OFF;

	return 0;
}

#ifdef CONFIG_PM

/*
 * LDM power management.
 */
static unsigned int neponset_saved_state;

static int neponset_suspend(struct platform_device *dev, pm_message_t state)
{
	/*
	 * Save state.
	 */
	neponset_saved_state = NCR_0;

	return 0;
}

static int neponset_resume(struct platform_device *dev)
{
	NCR_0 = neponset_saved_state;

	return 0;
}

#else
#define neponset_suspend NULL
#define neponset_resume  NULL
#endif

static struct platform_driver neponset_device_driver = {
	.probe		= neponset_probe,
	.suspend	= neponset_suspend,
	.resume		= neponset_resume,
	.driver		= {
		.name	= "neponset",
	},
};

static struct resource neponset_resources[] = {
	[0] = {
		.start	= 0x10000000,
		.end	= 0x17ffffff,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device neponset_device = {
	.name		= "neponset",
	.id		= 0,
	.num_resources	= ARRAY_SIZE(neponset_resources),
	.resource	= neponset_resources,
};

static struct resource sa1111_resources[] = {
	[0] = {
		.start	= 0x40000000,
		.end	= 0x40001fff,
		.flags	= IORESOURCE_MEM,
	},
	[1] = {
		.start	= IRQ_NEPONSET_SA1111,
		.end	= IRQ_NEPONSET_SA1111,
		.flags	= IORESOURCE_IRQ,
	},
};

static u64 sa1111_dmamask = 0xffffffffUL;

static struct platform_device sa1111_device = {
	.name		= "sa1111",
	.id		= 0,
	.dev		= {
		.dma_mask = &sa1111_dmamask,
		.coherent_dma_mask = 0xffffffff,
	},
	.num_resources	= ARRAY_SIZE(sa1111_resources),
	.resource	= sa1111_resources,
};

static struct resource smc91x_resources[] = {
	[0] = {
		.name	= "smc91x-regs",
		.start	= SA1100_CS3_PHYS,
		.end	= SA1100_CS3_PHYS + 0x01ffffff,
		.flags	= IORESOURCE_MEM,
	},
	[1] = {
		.start	= IRQ_NEPONSET_SMC9196,
		.end	= IRQ_NEPONSET_SMC9196,
		.flags	= IORESOURCE_IRQ,
	},
	[2] = {
		.name	= "smc91x-attrib",
		.start	= SA1100_CS3_PHYS + 0x02000000,
		.end	= SA1100_CS3_PHYS + 0x03ffffff,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device smc91x_device = {
	.name		= "smc91x",
	.id		= 0,
	.num_resources	= ARRAY_SIZE(smc91x_resources),
	.resource	= smc91x_resources,
};

static struct platform_device *devices[] __initdata = {
	&neponset_device,
	&sa1111_device,
	&smc91x_device,
};

extern void sa1110_mb_disable(void);

static int __init neponset_init(void)
{
	platform_driver_register(&neponset_device_driver);

	/*
	 * The Neponset is only present on the Assabet machine type.
	 */
	if (!machine_is_assabet())
		return -ENODEV;

	/*
	 * Ensure that the memory bus request/grant signals are setup,
	 * and the grant is held in its inactive state, whether or not
	 * we actually have a Neponset attached.
	 */
	sa1110_mb_disable();

	if (!machine_has_neponset()) {
		printk(KERN_DEBUG "Neponset expansion board not present\n");
		return -ENODEV;
	}

	if (WHOAMI != 0x11) {
		printk(KERN_WARNING "Neponset board detected, but "
			"wrong ID: %02x\n", WHOAMI);
		return -ENODEV;
	}

	return platform_add_devices(devices, ARRAY_SIZE(devices));
}

subsys_initcall(neponset_init);

static struct map_desc neponset_io_desc[] __initdata = {
	{	/* System Registers */
		.virtual	=  0xf3000000,
		.pfn		= __phys_to_pfn(0x10000000),
		.length		= SZ_1M,
		.type		= MT_DEVICE
	}, {	/* SA-1111 */
		.virtual	=  0xf4000000,
		.pfn		= __phys_to_pfn(0x40000000),
		.length		= SZ_1M,
		.type		= MT_DEVICE
	}
};

void __init neponset_map_io(void)
{
	iotable_init(neponset_io_desc, ARRAY_SIZE(neponset_io_desc));
}