Bootlin logo

Elixir Cross Referencer

   1
   2
   3
   4
   5
   6
   7
   8
   9
  10
  11
  12
  13
  14
  15
  16
  17
  18
  19
  20
  21
  22
  23
  24
  25
  26
  27
  28
  29
  30
  31
  32
  33
  34
  35
  36
  37
  38
  39
  40
  41
  42
  43
  44
  45
  46
  47
  48
  49
  50
  51
  52
  53
  54
  55
  56
  57
  58
  59
  60
  61
  62
  63
  64
  65
  66
  67
  68
  69
  70
  71
  72
  73
  74
  75
  76
  77
  78
  79
  80
  81
  82
  83
  84
  85
  86
  87
  88
  89
  90
  91
  92
  93
  94
  95
  96
  97
  98
  99
 100
 101
 102
 103
 104
 105
 106
 107
 108
 109
 110
 111
 112
 113
 114
 115
 116
 117
 118
 119
 120
 121
 122
 123
 124
 125
 126
 127
 128
 129
 130
 131
 132
 133
 134
 135
 136
 137
 138
 139
 140
 141
 142
 143
 144
 145
 146
 147
 148
 149
 150
 151
 152
 153
 154
 155
 156
 157
 158
 159
 160
 161
 162
 163
 164
 165
 166
 167
 168
 169
 170
 171
 172
 173
 174
 175
 176
 177
 178
 179
 180
 181
 182
 183
 184
 185
 186
 187
 188
 189
 190
 191
 192
 193
 194
 195
 196
 197
 198
 199
 200
 201
 202
 203
 204
 205
 206
 207
 208
 209
 210
 211
 212
 213
 214
 215
 216
 217
 218
 219
 220
 221
 222
 223
 224
 225
 226
 227
 228
 229
 230
 231
 232
 233
 234
 235
 236
 237
 238
 239
 240
 241
 242
 243
 244
 245
 246
 247
 248
 249
 250
 251
 252
 253
 254
 255
 256
 257
 258
 259
 260
 261
 262
 263
 264
 265
 266
 267
 268
 269
 270
 271
 272
 273
 274
 275
 276
 277
 278
 279
 280
 281
 282
 283
 284
 285
 286
 287
 288
 289
 290
 291
 292
 293
 294
 295
 296
 297
 298
 299
 300
 301
 302
 303
 304
 305
 306
 307
 308
 309
 310
 311
 312
 313
 314
 315
 316
 317
 318
 319
 320
 321
 322
 323
 324
 325
 326
 327
 328
 329
 330
 331
 332
 333
 334
 335
 336
 337
 338
 339
 340
 341
 342
 343
 344
 345
 346
 347
 348
 349
 350
 351
 352
 353
 354
 355
 356
 357
 358
 359
 360
 361
 362
 363
 364
 365
 366
 367
 368
 369
 370
 371
 372
 373
 374
 375
 376
 377
 378
 379
 380
 381
 382
 383
 384
 385
 386
 387
 388
 389
 390
 391
 392
 393
 394
 395
 396
 397
 398
 399
 400
 401
 402
 403
 404
 405
 406
 407
 408
 409
 410
 411
 412
 413
 414
 415
 416
 417
 418
 419
 420
 421
 422
 423
 424
 425
 426
 427
 428
 429
 430
 431
 432
 433
 434
 435
 436
 437
 438
 439
 440
 441
 442
 443
 444
 445
 446
 447
 448
 449
 450
 451
 452
 453
 454
 455
 456
 457
 458
 459
 460
 461
 462
 463
 464
 465
 466
 467
 468
 469
 470
 471
 472
 473
 474
 475
 476
 477
 478
 479
 480
 481
 482
 483
 484
 485
 486
 487
 488
 489
 490
 491
 492
 493
 494
 495
 496
 497
 498
 499
 500
 501
 502
 503
 504
 505
 506
 507
 508
 509
 510
 511
 512
 513
 514
 515
 516
 517
 518
 519
 520
 521
 522
 523
 524
 525
 526
 527
 528
 529
 530
 531
 532
 533
 534
 535
 536
 537
 538
 539
 540
 541
 542
 543
 544
 545
 546
 547
 548
 549
 550
 551
 552
 553
 554
 555
 556
 557
 558
 559
 560
 561
 562
 563
 564
 565
 566
 567
 568
 569
 570
 571
 572
 573
 574
 575
 576
 577
 578
 579
 580
 581
 582
 583
 584
 585
 586
 587
 588
 589
 590
 591
 592
 593
 594
 595
 596
 597
 598
 599
 600
 601
 602
 603
 604
 605
 606
 607
 608
 609
 610
 611
 612
 613
 614
 615
 616
 617
 618
 619
 620
 621
 622
 623
 624
 625
 626
 627
 628
 629
 630
 631
 632
 633
 634
 635
 636
 637
 638
 639
 640
 641
 642
 643
 644
 645
 646
 647
 648
 649
 650
 651
 652
 653
 654
 655
 656
 657
 658
 659
 660
 661
 662
 663
 664
 665
 666
 667
 668
 669
 670
 671
 672
 673
 674
 675
 676
 677
 678
 679
 680
 681
 682
 683
 684
 685
 686
 687
 688
 689
 690
 691
 692
 693
 694
 695
 696
 697
 698
 699
 700
 701
 702
 703
 704
 705
 706
 707
 708
 709
 710
 711
 712
 713
 714
 715
 716
 717
 718
 719
 720
 721
 722
 723
 724
 725
 726
 727
 728
 729
 730
 731
 732
 733
 734
 735
 736
 737
 738
 739
 740
 741
 742
 743
 744
 745
 746
 747
 748
 749
 750
 751
 752
 753
 754
 755
 756
 757
 758
 759
 760
 761
 762
 763
 764
 765
 766
 767
 768
 769
 770
 771
 772
 773
 774
 775
 776
 777
 778
 779
 780
 781
 782
 783
 784
 785
 786
 787
 788
 789
 790
 791
 792
 793
 794
 795
 796
 797
 798
 799
 800
 801
 802
 803
 804
 805
 806
 807
 808
 809
 810
 811
 812
 813
 814
 815
 816
 817
 818
 819
 820
 821
 822
 823
 824
 825
 826
 827
 828
 829
 830
 831
 832
 833
 834
 835
 836
 837
 838
 839
 840
 841
 842
 843
 844
 845
 846
 847
 848
 849
 850
 851
 852
 853
 854
 855
 856
 857
 858
 859
 860
 861
 862
 863
 864
 865
 866
 867
 868
 869
 870
 871
 872
 873
 874
 875
 876
 877
 878
 879
 880
 881
 882
 883
 884
 885
 886
 887
 888
 889
 890
 891
 892
 893
 894
 895
 896
 897
 898
 899
 900
 901
 902
 903
 904
 905
 906
 907
 908
 909
 910
 911
 912
 913
 914
 915
 916
 917
 918
 919
 920
 921
 922
 923
 924
 925
 926
 927
 928
 929
 930
 931
 932
 933
 934
 935
 936
 937
 938
 939
 940
 941
 942
 943
 944
 945
 946
 947
 948
 949
 950
 951
 952
 953
 954
 955
 956
 957
 958
 959
 960
 961
 962
 963
 964
 965
 966
 967
 968
 969
 970
 971
 972
 973
 974
 975
 976
 977
 978
 979
 980
 981
 982
 983
 984
 985
 986
 987
 988
 989
 990
 991
 992
 993
 994
 995
 996
 997
 998
 999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
/*
 * spcp8x5 USB to serial adaptor driver
 *
 * Copyright (C) 2006 Linxb (xubin.lin@worldplus.com.cn)
 * Copyright (C) 2006 S1 Corp.
 *
 * Original driver for 2.6.10 pl2303 driver by
 *   Greg Kroah-Hartman (greg@kroah.com)
 * Changes for 2.6.20 by Harald Klein <hari@vt100.at>
 *
 *	This program is free software; you can redistribute it and/or modify
 *	it under the terms of the GNU General Public License as published by
 *	the Free Software Foundation; either version 2 of the License, or
 *	(at your option) any later version.
 *
 *
 */
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>


/* Version Information */
#define DRIVER_VERSION 	"v0.04"
#define DRIVER_DESC 	"SPCP8x5 USB to serial adaptor driver"

static int debug;

#define SPCP8x5_007_VID		0x04FC
#define SPCP8x5_007_PID		0x0201
#define SPCP8x5_008_VID		0x04fc
#define SPCP8x5_008_PID		0x0235
#define SPCP8x5_PHILIPS_VID	0x0471
#define SPCP8x5_PHILIPS_PID	0x081e
#define SPCP8x5_INTERMATIC_VID	0x04FC
#define SPCP8x5_INTERMATIC_PID	0x0204
#define SPCP8x5_835_VID		0x04fc
#define SPCP8x5_835_PID		0x0231

static struct usb_device_id id_table [] = {
	{ USB_DEVICE(SPCP8x5_PHILIPS_VID , SPCP8x5_PHILIPS_PID)},
	{ USB_DEVICE(SPCP8x5_INTERMATIC_VID, SPCP8x5_INTERMATIC_PID)},
	{ USB_DEVICE(SPCP8x5_835_VID, SPCP8x5_835_PID)},
	{ USB_DEVICE(SPCP8x5_008_VID, SPCP8x5_008_PID)},
	{ USB_DEVICE(SPCP8x5_007_VID, SPCP8x5_007_PID)},
	{ }					/* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, id_table);

struct spcp8x5_usb_ctrl_arg {
	u8 	type;
	u8	cmd;
	u8	cmd_type;
	u16	value;
	u16	index;
	u16	length;
};

/* wait 30s before close */
#define SPCP8x5_CLOSING_WAIT	(30*HZ)

#define SPCP8x5_BUF_SIZE	1024


/* spcp8x5 spec register define */
#define MCR_CONTROL_LINE_RTS		0x02
#define MCR_CONTROL_LINE_DTR		0x01
#define MCR_DTR				0x01
#define MCR_RTS				0x02

#define MSR_STATUS_LINE_DCD		0x80
#define MSR_STATUS_LINE_RI		0x40
#define MSR_STATUS_LINE_DSR		0x20
#define MSR_STATUS_LINE_CTS		0x10

/* verdor command here , we should define myself */
#define SET_DEFAULT			0x40
#define SET_DEFAULT_TYPE		0x20

#define SET_UART_FORMAT			0x40
#define SET_UART_FORMAT_TYPE		0x21
#define SET_UART_FORMAT_SIZE_5		0x00
#define SET_UART_FORMAT_SIZE_6		0x01
#define SET_UART_FORMAT_SIZE_7		0x02
#define SET_UART_FORMAT_SIZE_8		0x03
#define SET_UART_FORMAT_STOP_1		0x00
#define SET_UART_FORMAT_STOP_2		0x04
#define SET_UART_FORMAT_PAR_NONE	0x00
#define SET_UART_FORMAT_PAR_ODD		0x10
#define SET_UART_FORMAT_PAR_EVEN	0x30
#define SET_UART_FORMAT_PAR_MASK	0xD0
#define SET_UART_FORMAT_PAR_SPACE	0x90

#define GET_UART_STATUS_TYPE		0xc0
#define GET_UART_STATUS			0x22
#define GET_UART_STATUS_MSR		0x06

#define SET_UART_STATUS			0x40
#define SET_UART_STATUS_TYPE		0x23
#define SET_UART_STATUS_MCR		0x0004
#define SET_UART_STATUS_MCR_DTR		0x01
#define SET_UART_STATUS_MCR_RTS		0x02
#define SET_UART_STATUS_MCR_LOOP	0x10

#define SET_WORKING_MODE		0x40
#define SET_WORKING_MODE_TYPE		0x24
#define SET_WORKING_MODE_U2C		0x00
#define SET_WORKING_MODE_RS485		0x01
#define SET_WORKING_MODE_PDMA		0x02
#define SET_WORKING_MODE_SPP		0x03

#define SET_FLOWCTL_CHAR		0x40
#define SET_FLOWCTL_CHAR_TYPE		0x25

#define GET_VERSION			0xc0
#define GET_VERSION_TYPE		0x26

#define SET_REGISTER			0x40
#define SET_REGISTER_TYPE		0x27

#define	GET_REGISTER			0xc0
#define GET_REGISTER_TYPE		0x28

#define SET_RAM				0x40
#define SET_RAM_TYPE			0x31

#define GET_RAM				0xc0
#define GET_RAM_TYPE			0x32

/* how come ??? */
#define UART_STATE			0x08
#define UART_STATE_TRANSIENT_MASK	0x74
#define UART_DCD			0x01
#define UART_DSR			0x02
#define UART_BREAK_ERROR		0x04
#define UART_RING			0x08
#define UART_FRAME_ERROR		0x10
#define UART_PARITY_ERROR		0x20
#define UART_OVERRUN_ERROR		0x40
#define UART_CTS			0x80

enum spcp8x5_type {
	SPCP825_007_TYPE,
	SPCP825_008_TYPE,
	SPCP825_PHILIP_TYPE,
	SPCP825_INTERMATIC_TYPE,
	SPCP835_TYPE,
};

/* 1st in 1st out buffer 4 driver */
struct ringbuf {
	unsigned int	buf_size;
	char		*buf_buf;
	char		*buf_get;
	char		*buf_put;
};

/* alloc the ring buf and alloc the buffer itself */
static inline struct ringbuf *alloc_ringbuf(unsigned int size)
{
	struct ringbuf *pb;

	if (size == 0)
		return NULL;

	pb = kmalloc(sizeof(*pb), GFP_KERNEL);
	if (pb == NULL)
		return NULL;

	pb->buf_buf = kmalloc(size, GFP_KERNEL);
	if (pb->buf_buf == NULL) {
		kfree(pb);
		return NULL;
	}

	pb->buf_size = size;
	pb->buf_get = pb->buf_put = pb->buf_buf;

	return pb;
}

/* free the ring buf and the buffer itself */
static inline void free_ringbuf(struct ringbuf *pb)
{
	if (pb != NULL) {
		kfree(pb->buf_buf);
		kfree(pb);
	}
}

/* clear pipo , juest repoint the pointer here */
static inline void clear_ringbuf(struct ringbuf *pb)
{
	if (pb != NULL)
		pb->buf_get = pb->buf_put;
}

/* get the number of data in the pipo */
static inline unsigned int ringbuf_avail_data(struct ringbuf *pb)
{
	if (pb == NULL)
		return 0;
	return (pb->buf_size + pb->buf_put - pb->buf_get) % pb->buf_size;
}

/* get the number of space in the pipo */
static inline unsigned int ringbuf_avail_space(struct ringbuf *pb)
{
	if (pb == NULL)
		return 0;
	return (pb->buf_size + pb->buf_get - pb->buf_put - 1) % pb->buf_size;
}

/* put count data into pipo */
static unsigned int put_ringbuf(struct ringbuf *pb, const char *buf,
				unsigned int count)
{
	unsigned int len;

	if (pb == NULL)
		return 0;

	len  = ringbuf_avail_space(pb);
	if (count > len)
		count = len;

	if (count == 0)
		return 0;

	len = pb->buf_buf + pb->buf_size - pb->buf_put;
	if (count > len) {
		memcpy(pb->buf_put, buf, len);
		memcpy(pb->buf_buf, buf+len, count - len);
		pb->buf_put = pb->buf_buf + count - len;
	} else {
		memcpy(pb->buf_put, buf, count);
		if (count < len)
			pb->buf_put += count;
		else /* count == len */
			pb->buf_put = pb->buf_buf;
	}
	return count;
}

/* get count data from pipo */
static unsigned int get_ringbuf(struct ringbuf *pb, char *buf,
				unsigned int count)
{
	unsigned int len;

	if (pb == NULL || buf == NULL)
		return 0;

	len = ringbuf_avail_data(pb);
	if (count > len)
		count = len;

	if (count == 0)
		return 0;

	len = pb->buf_buf + pb->buf_size - pb->buf_get;
	if (count > len) {
		memcpy(buf, pb->buf_get, len);
		memcpy(buf+len, pb->buf_buf, count - len);
		pb->buf_get = pb->buf_buf + count - len;
	} else {
		memcpy(buf, pb->buf_get, count);
		if (count < len)
			pb->buf_get += count;
		else /* count == len */
			pb->buf_get = pb->buf_buf;
	}

	return count;
}

static struct usb_driver spcp8x5_driver = {
	.name =			"spcp8x5",
	.probe =		usb_serial_probe,
	.disconnect =		usb_serial_disconnect,
	.id_table =		id_table,
	.no_dynamic_id =	1,
};


struct spcp8x5_private {
	spinlock_t 	lock;
	struct ringbuf	*buf;
	int 		write_urb_in_use;
	enum spcp8x5_type	type;
	wait_queue_head_t	delta_msr_wait;
	u8 			line_control;
	u8 			line_status;
	u8 			termios_initialized;
};

/* desc : when device plug in,this function would be called.
 * thanks to usb_serial subsystem,then do almost every things for us. And what
 * we should do just alloc the buffer */
static int spcp8x5_startup(struct usb_serial *serial)
{
	struct spcp8x5_private *priv;
	int i;
	enum spcp8x5_type type = SPCP825_007_TYPE;
	u16 product = le16_to_cpu(serial->dev->descriptor.idProduct);

	if (product == 0x0201)
		type = SPCP825_007_TYPE;
	else if (product == 0x0231)
		type = SPCP835_TYPE;
	else if (product == 0x0235)
		type = SPCP825_008_TYPE;
	else if (product == 0x0204)
		type = SPCP825_INTERMATIC_TYPE;
	else if (product == 0x0471 &&
		 serial->dev->descriptor.idVendor == cpu_to_le16(0x081e))
		type = SPCP825_PHILIP_TYPE;
	dev_dbg(&serial->dev->dev, "device type = %d\n", (int)type);

	for (i = 0; i < serial->num_ports; ++i) {
		priv = kzalloc(sizeof(struct spcp8x5_private), GFP_KERNEL);
		if (!priv)
			goto cleanup;

		spin_lock_init(&priv->lock);
		priv->buf = alloc_ringbuf(SPCP8x5_BUF_SIZE);
		if (priv->buf == NULL)
			goto cleanup2;

		init_waitqueue_head(&priv->delta_msr_wait);
		priv->type = type;
		usb_set_serial_port_data(serial->port[i] , priv);

	}

	return 0;

cleanup2:
	kfree(priv);
cleanup:
	for (--i; i >= 0; --i) {
		priv = usb_get_serial_port_data(serial->port[i]);
		free_ringbuf(priv->buf);
		kfree(priv);
		usb_set_serial_port_data(serial->port[i] , NULL);
	}
	return -ENOMEM;
}

/* call when the device plug out. free all the memory alloced by probe */
static void spcp8x5_shutdown(struct usb_serial *serial)
{
	int i;
	struct spcp8x5_private *priv;

	for (i = 0; i < serial->num_ports; i++) {
		priv = usb_get_serial_port_data(serial->port[i]);
		if (priv) {
			free_ringbuf(priv->buf);
			kfree(priv);
			usb_set_serial_port_data(serial->port[i] , NULL);
		}
	}
}

/* set the modem control line of the device.
 * NOTE spcp825-007 not supported this */
static int spcp8x5_set_ctrlLine(struct usb_device *dev, u8 value,
				enum spcp8x5_type type)
{
	int retval;
	u8 mcr = 0 ;

	if (type == SPCP825_007_TYPE)
		return -EPERM;

	mcr = (unsigned short)value;
	retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
				 SET_UART_STATUS_TYPE, SET_UART_STATUS,
				 mcr, 0x04, NULL, 0, 100);
	if (retval != 0)
		dev_dbg(&dev->dev, "usb_control_msg return %#x\n", retval);
	return retval;
}

/* get the modem status register of the device
 * NOTE spcp825-007 not supported this */
static int spcp8x5_get_msr(struct usb_device *dev, u8 *status,
			   enum spcp8x5_type type)
{
	u8 *status_buffer;
	int ret;

	/* I return Permited not support here but seem inval device
	 * is more fix */
	if (type == SPCP825_007_TYPE)
		return -EPERM;
	if (status == NULL)
		return -EINVAL;

	status_buffer = kmalloc(1, GFP_KERNEL);
	if (!status_buffer)
		return -ENOMEM;
	status_buffer[0] = status[0];

	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
			      GET_UART_STATUS, GET_UART_STATUS_TYPE,
			      0, GET_UART_STATUS_MSR, status_buffer, 1, 100);
	if (ret < 0)
		dev_dbg(&dev->dev, "Get MSR = 0x%p failed (error = %d)",
			status_buffer, ret);

	dev_dbg(&dev->dev, "0xc0:0x22:0:6  %d - 0x%p ", ret, status_buffer);
	status[0] = status_buffer[0];
	kfree(status_buffer);

	return ret;
}

/* select the work mode.
 * NOTE this function not supported by spcp825-007 */
static void spcp8x5_set_workMode(struct usb_device *dev, u16 value,
				 u16 index, enum spcp8x5_type type)
{
	int ret;

	/* I return Permited not support here but seem inval device
	 * is more fix */
	if (type == SPCP825_007_TYPE)
		return;

	ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
			      SET_WORKING_MODE_TYPE, SET_WORKING_MODE,
			      value, index, NULL, 0, 100);
	dev_dbg(&dev->dev, "value = %#x , index = %#x\n", value, index);
	if (ret < 0)
		dev_dbg(&dev->dev,
			"RTSCTS usb_control_msg(enable flowctrl) = %d\n", ret);
}

/* close the serial port. We should wait for data sending to device 1st and
 * then kill all urb. */
static void spcp8x5_close(struct tty_struct *tty,
			struct usb_serial_port *port, struct file *filp)
{
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;
	unsigned int c_cflag;
	int bps;
	long timeout;
	wait_queue_t wait;
	int result;

	dbg("%s - port %d", __func__, port->number);

	/* wait for data to drain from the buffer */
	spin_lock_irqsave(&priv->lock, flags);
	timeout = SPCP8x5_CLOSING_WAIT;
	init_waitqueue_entry(&wait, current);
	add_wait_queue(&tty->write_wait, &wait);
	for (;;) {
		set_current_state(TASK_INTERRUPTIBLE);
		if (ringbuf_avail_data(priv->buf) == 0 ||
		    timeout == 0 || signal_pending(current))
			break;
		spin_unlock_irqrestore(&priv->lock, flags);
		timeout = schedule_timeout(timeout);
		spin_lock_irqsave(&priv->lock, flags);
	}
	set_current_state(TASK_RUNNING);
	remove_wait_queue(&tty->write_wait, &wait);

	/* clear out any remaining data in the buffer */
	clear_ringbuf(priv->buf);
	spin_unlock_irqrestore(&priv->lock, flags);

	/* wait for characters to drain from the device (this is long enough
	 * for the entire all byte spcp8x5 hardware buffer to drain with no
	 * flow control for data rates of 1200 bps or more, for lower rates we
	 * should really know how much data is in the buffer to compute a delay
	 * that is not unnecessarily long) */
	bps = tty_get_baud_rate(tty);
	if (bps > 1200)
		timeout = max((HZ*2560) / bps, HZ/10);
	else
		timeout = 2*HZ;
	set_current_state(TASK_INTERRUPTIBLE);
	schedule_timeout(timeout);

	/* clear control lines */
	if (tty) {
		c_cflag = tty->termios->c_cflag;
		if (c_cflag & HUPCL) {
			spin_lock_irqsave(&priv->lock, flags);
			priv->line_control = 0;
			spin_unlock_irqrestore(&priv->lock, flags);
			spcp8x5_set_ctrlLine(port->serial->dev, 0 , priv->type);
		}
	}

	/* kill urb */
	if (port->write_urb != NULL) {
		result = usb_unlink_urb(port->write_urb);
		if (result)
			dev_dbg(&port->dev,
				"usb_unlink_urb(write_urb) = %d\n", result);
	}
	result = usb_unlink_urb(port->read_urb);
	if (result)
		dev_dbg(&port->dev, "usb_unlink_urb(read_urb) = %d\n", result);
}

/* set the serial param for transfer. we should check if we really need to
 * transfer. if we set flow control we should do this too. */
static void spcp8x5_set_termios(struct tty_struct *tty,
		struct usb_serial_port *port, struct ktermios *old_termios)
{
	struct usb_serial *serial = port->serial;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;
	unsigned int cflag = tty->termios->c_cflag;
	unsigned int old_cflag = old_termios->c_cflag;
	unsigned short uartdata;
	unsigned char buf[2] = {0, 0};
	int baud;
	int i;
	u8 control;

	/* for the 1st time call this function */
	spin_lock_irqsave(&priv->lock, flags);
	if (!priv->termios_initialized) {
		*(tty->termios) = tty_std_termios;
		tty->termios->c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
		tty->termios->c_ispeed = 115200;
		tty->termios->c_ospeed = 115200;
		priv->termios_initialized = 1;
	}
	spin_unlock_irqrestore(&priv->lock, flags);

	/* check that they really want us to change something */
	if (!tty_termios_hw_change(tty->termios, old_termios))
		return;

	/* set DTR/RTS active */
	spin_lock_irqsave(&priv->lock, flags);
	control = priv->line_control;
	if ((old_cflag & CBAUD) == B0) {
		priv->line_control |= MCR_DTR;
		if (!(old_cflag & CRTSCTS))
			priv->line_control |= MCR_RTS;
	}
	if (control != priv->line_control) {
		control = priv->line_control;
		spin_unlock_irqrestore(&priv->lock, flags);
		spcp8x5_set_ctrlLine(serial->dev, control , priv->type);
	} else {
		spin_unlock_irqrestore(&priv->lock, flags);
	}

	/* Set Baud Rate */
	baud = tty_get_baud_rate(tty);;
	switch (baud) {
	case 300:	buf[0] = 0x00;	break;
	case 600:	buf[0] = 0x01;	break;
	case 1200:	buf[0] = 0x02;	break;
	case 2400:	buf[0] = 0x03;	break;
	case 4800:	buf[0] = 0x04;	break;
	case 9600:	buf[0] = 0x05;	break;
	case 19200:	buf[0] = 0x07;	break;
	case 38400:	buf[0] = 0x09;	break;
	case 57600:	buf[0] = 0x0a;	break;
	case 115200:	buf[0] = 0x0b;	break;
	case 230400:	buf[0] = 0x0c;	break;
	case 460800:	buf[0] = 0x0d;	break;
	case 921600:	buf[0] = 0x0e;	break;
/*	case 1200000:	buf[0] = 0x0f;	break; */
/*	case 2400000:	buf[0] = 0x10;	break; */
	case 3000000:	buf[0] = 0x11;	break;
/*	case 6000000:	buf[0] = 0x12;	break; */
	case 0:
	case 1000000:
			buf[0] = 0x0b;	break;
	default:
		err("spcp825 driver does not support the baudrate "
		    "requested, using default of 9600.");
	}

	/* Set Data Length : 00:5bit, 01:6bit, 10:7bit, 11:8bit */
	if (cflag & CSIZE) {
		switch (cflag & CSIZE) {
		case CS5:
			buf[1] |= SET_UART_FORMAT_SIZE_5;
			break;
		case CS6:
			buf[1] |= SET_UART_FORMAT_SIZE_6;
			break;
		case CS7:
			buf[1] |= SET_UART_FORMAT_SIZE_7;
			break;
		default:
		case CS8:
			buf[1] |= SET_UART_FORMAT_SIZE_8;
			break;
		}
	}

	/* Set Stop bit2 : 0:1bit 1:2bit */
	buf[1] |= (cflag & CSTOPB) ? SET_UART_FORMAT_STOP_2 :
				     SET_UART_FORMAT_STOP_1;

	/* Set Parity bit3-4 01:Odd 11:Even */
	if (cflag & PARENB) {
		buf[1] |= (cflag & PARODD) ?
		SET_UART_FORMAT_PAR_ODD : SET_UART_FORMAT_PAR_EVEN ;
	} else
		buf[1] |= SET_UART_FORMAT_PAR_NONE;

	uartdata = buf[0] | buf[1]<<8;

	i = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
			    SET_UART_FORMAT_TYPE, SET_UART_FORMAT,
			    uartdata, 0, NULL, 0, 100);
	if (i < 0)
		err("Set UART format %#x failed (error = %d)", uartdata, i);
	dbg("0x21:0x40:0:0  %d\n", i);

	if (cflag & CRTSCTS) {
		/* enable hardware flow control */
		spcp8x5_set_workMode(serial->dev, 0x000a,
				     SET_WORKING_MODE_U2C, priv->type);
	}
	return;
}

/* open the serial port. do some usb system call. set termios and get the line
 * status of the device. then submit the read urb */
static int spcp8x5_open(struct tty_struct *tty,
			struct usb_serial_port *port, struct file *filp)
{
	struct ktermios tmp_termios;
	struct usb_serial *serial = port->serial;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	int ret;
	unsigned long flags;
	u8 status = 0x30;
	/* status 0x30 means DSR and CTS = 1 other CDC RI and delta = 0 */

	dbg("%s -  port %d", __func__, port->number);

	usb_clear_halt(serial->dev, port->write_urb->pipe);
	usb_clear_halt(serial->dev, port->read_urb->pipe);

	ret = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
			      0x09, 0x00,
			      0x01, 0x00, NULL, 0x00, 100);
	if (ret)
		return ret;

	spin_lock_irqsave(&priv->lock, flags);
	if (tty && (tty->termios->c_cflag & CBAUD))
		priv->line_control = MCR_DTR | MCR_RTS;
	else
		priv->line_control = 0;
	spin_unlock_irqrestore(&priv->lock, flags);

	spcp8x5_set_ctrlLine(serial->dev, priv->line_control , priv->type);

	/* Setup termios */
	if (tty)
		spcp8x5_set_termios(tty, port, &tmp_termios);

	spcp8x5_get_msr(serial->dev, &status, priv->type);

	/* may be we should update uart status here but now we did not do */
	spin_lock_irqsave(&priv->lock, flags);
	priv->line_status = status & 0xf0 ;
	spin_unlock_irqrestore(&priv->lock, flags);

	/* FIXME: need to assert RTS and DTR if CRTSCTS off */

	dbg("%s - submitting read urb", __func__);
	port->read_urb->dev = serial->dev;
	ret = usb_submit_urb(port->read_urb, GFP_KERNEL);
	if (ret) {
		spcp8x5_close(tty, port, NULL);
		return -EPROTO;
	}
	return 0;
}

/* bulk read call back function. check the status of the urb. if transfer
 * failed return. then update the status and the tty send data to tty subsys.
 * submit urb again.
 */
static void spcp8x5_read_bulk_callback(struct urb *urb)
{
	struct usb_serial_port *port = urb->context;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	struct tty_struct *tty;
	unsigned char *data = urb->transfer_buffer;
	unsigned long flags;
	int i;
	int result;
	u8 status = 0;
	char tty_flag;

	dev_dbg(&port->dev, "start, urb->status = %d, "
		"urb->actual_length = %d\n,", urb->status, urb->actual_length);

	/* check the urb status */
	if (urb->status) {
		if (!port->port.count)
			return;
		if (urb->status == -EPROTO) {
			/* spcp8x5 mysteriously fails with -EPROTO */
			/* reschedule the read */
			urb->status = 0;
			urb->dev = port->serial->dev;
			result = usb_submit_urb(urb , GFP_ATOMIC);
			if (result)
				dev_dbg(&port->dev,
					"failed submitting read urb %d\n",
					result);
			return;
		}
		dev_dbg(&port->dev, "unable to handle the error, exiting.\n");
		return;
	}

	/* get tty_flag from status */
	tty_flag = TTY_NORMAL;

	spin_lock_irqsave(&priv->lock, flags);
	status = priv->line_status;
	priv->line_status &= ~UART_STATE_TRANSIENT_MASK;
	spin_unlock_irqrestore(&priv->lock, flags);
	/* wake up the wait for termios */
	wake_up_interruptible(&priv->delta_msr_wait);

	/* break takes precedence over parity, which takes precedence over
	 * framing errors */
	if (status & UART_BREAK_ERROR)
		tty_flag = TTY_BREAK;
	else if (status & UART_PARITY_ERROR)
		tty_flag = TTY_PARITY;
	else if (status & UART_FRAME_ERROR)
		tty_flag = TTY_FRAME;
	dev_dbg(&port->dev, "tty_flag = %d\n", tty_flag);

	tty = port->port.tty;
	if (tty && urb->actual_length) {
		tty_buffer_request_room(tty, urb->actual_length + 1);
		/* overrun is special, not associated with a char */
		if (status & UART_OVERRUN_ERROR)
			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
		for (i = 0; i < urb->actual_length; ++i)
			tty_insert_flip_char(tty, data[i], tty_flag);
		tty_flip_buffer_push(tty);
	}

	/* Schedule the next read _if_ we are still open */
	if (port->port.count) {
		urb->dev = port->serial->dev;
		result = usb_submit_urb(urb , GFP_ATOMIC);
		if (result)
			dev_dbg(&port->dev, "failed submitting read urb %d\n",
				result);
	}

	return;
}

/* get data from ring buffer and then write to usb bus */
static void spcp8x5_send(struct usb_serial_port *port)
{
	int count, result;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;

	spin_lock_irqsave(&priv->lock, flags);

	if (priv->write_urb_in_use) {
		dev_dbg(&port->dev, "write urb still used\n");
		spin_unlock_irqrestore(&priv->lock, flags);
		return;
	}

	/* send the 1st urb for writting */
	memset(port->write_urb->transfer_buffer , 0x00 , port->bulk_out_size);
	count = get_ringbuf(priv->buf, port->write_urb->transfer_buffer,
		port->bulk_out_size);

	if (count == 0) {
		spin_unlock_irqrestore(&priv->lock, flags);
		return;
	}

	/* update the urb status */
	priv->write_urb_in_use = 1;

	spin_unlock_irqrestore(&priv->lock, flags);

	port->write_urb->transfer_buffer_length = count;
	port->write_urb->dev = port->serial->dev;

	result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
	if (result) {
		dev_dbg(&port->dev, "failed submitting write urb, error %d\n",
			result);
		priv->write_urb_in_use = 0;
		/* TODO: reschedule spcp8x5_send */
	}


	schedule_work(&port->work);
}

/* this is the call back function for write urb. NOTE we should not sleep in
 * this routine. check the urb return code and then submit the write urb again
 * to hold the write loop */
static void spcp8x5_write_bulk_callback(struct urb *urb)
{
	struct usb_serial_port *port = urb->context;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	int result;

	switch (urb->status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dev_dbg(&port->dev, "urb shutting down with status: %d\n",
			urb->status);
		priv->write_urb_in_use = 0;
		return;
	default:
		/* error in the urb, so we have to resubmit it */
		dbg("%s - Overflow in write", __func__);
		dbg("%s - nonzero write bulk status received: %d",
			__func__, urb->status);
		port->write_urb->transfer_buffer_length = 1;
		port->write_urb->dev = port->serial->dev;
		result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
		if (result)
			dev_dbg(&port->dev,
				"failed resubmitting write urb %d\n", result);
		else
			return;
	}

	priv->write_urb_in_use = 0;

	/* send any buffered data */
	spcp8x5_send(port);
}

/* write data to ring buffer. and then start the write transfer */
static int spcp8x5_write(struct tty_struct *tty, struct usb_serial_port *port,
			 const unsigned char *buf, int count)
{
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;

	dev_dbg(&port->dev, "%d bytes\n", count);

	if (!count)
		return count;

	spin_lock_irqsave(&priv->lock, flags);
	count = put_ringbuf(priv->buf, buf, count);
	spin_unlock_irqrestore(&priv->lock, flags);

	spcp8x5_send(port);

	return count;
}

static int spcp8x5_wait_modem_info(struct usb_serial_port *port,
				   unsigned int arg)
{
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;
	unsigned int prevstatus;
	unsigned int status;
	unsigned int changed;

	spin_lock_irqsave(&priv->lock, flags);
	prevstatus = priv->line_status;
	spin_unlock_irqrestore(&priv->lock, flags);

	while (1) {
		/* wake up in bulk read */
		interruptible_sleep_on(&priv->delta_msr_wait);

		/* see if a signal did it */
		if (signal_pending(current))
			return -ERESTARTSYS;

		spin_lock_irqsave(&priv->lock, flags);
		status = priv->line_status;
		spin_unlock_irqrestore(&priv->lock, flags);

		changed = prevstatus^status;

		if (((arg & TIOCM_RNG) && (changed & MSR_STATUS_LINE_RI)) ||
		    ((arg & TIOCM_DSR) && (changed & MSR_STATUS_LINE_DSR)) ||
		    ((arg & TIOCM_CD)  && (changed & MSR_STATUS_LINE_DCD)) ||
		    ((arg & TIOCM_CTS) && (changed & MSR_STATUS_LINE_CTS)))
			return 0;

		prevstatus = status;
	}
	/* NOTREACHED */
	return 0;
}

static int spcp8x5_ioctl(struct tty_struct *tty, struct file *file,
			 unsigned int cmd, unsigned long arg)
{
	struct usb_serial_port *port = tty->driver_data;
	dbg("%s (%d) cmd = 0x%04x", __func__, port->number, cmd);

	switch (cmd) {
	case TIOCMIWAIT:
		dbg("%s (%d) TIOCMIWAIT", __func__,  port->number);
		return spcp8x5_wait_modem_info(port, arg);

	default:
		dbg("%s not supported = 0x%04x", __func__, cmd);
		break;
	}

	return -ENOIOCTLCMD;
}

static int spcp8x5_tiocmset(struct tty_struct *tty, struct file *file,
			    unsigned int set, unsigned int clear)
{
	struct usb_serial_port *port = tty->driver_data;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;
	u8 control;

	spin_lock_irqsave(&priv->lock, flags);
	if (set & TIOCM_RTS)
		priv->line_control |= MCR_RTS;
	if (set & TIOCM_DTR)
		priv->line_control |= MCR_DTR;
	if (clear & TIOCM_RTS)
		priv->line_control &= ~MCR_RTS;
	if (clear & TIOCM_DTR)
		priv->line_control &= ~MCR_DTR;
	control = priv->line_control;
	spin_unlock_irqrestore(&priv->lock, flags);

	return spcp8x5_set_ctrlLine(port->serial->dev, control , priv->type);
}

static int spcp8x5_tiocmget(struct tty_struct *tty, struct file *file)
{
	struct usb_serial_port *port = tty->driver_data;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;
	unsigned int mcr;
	unsigned int status;
	unsigned int result;

	spin_lock_irqsave(&priv->lock, flags);
	mcr = priv->line_control;
	status = priv->line_status;
	spin_unlock_irqrestore(&priv->lock, flags);

	result = ((mcr & MCR_DTR)			? TIOCM_DTR : 0)
		  | ((mcr & MCR_RTS)			? TIOCM_RTS : 0)
		  | ((status & MSR_STATUS_LINE_CTS)	? TIOCM_CTS : 0)
		  | ((status & MSR_STATUS_LINE_DSR)	? TIOCM_DSR : 0)
		  | ((status & MSR_STATUS_LINE_RI)	? TIOCM_RI  : 0)
		  | ((status & MSR_STATUS_LINE_DCD)	? TIOCM_CD  : 0);

	return result;
}

/* get the avail space room in ring buffer */
static int spcp8x5_write_room(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	int room = 0;
	unsigned long flags;

	spin_lock_irqsave(&priv->lock, flags);
	room = ringbuf_avail_space(priv->buf);
	spin_unlock_irqrestore(&priv->lock, flags);

	return room;
}

/* get the number of avail data in write ring buffer */
static int spcp8x5_chars_in_buffer(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
	int chars = 0;
	unsigned long flags;

	spin_lock_irqsave(&priv->lock, flags);
	chars = ringbuf_avail_data(priv->buf);
	spin_unlock_irqrestore(&priv->lock, flags);

	return chars;
}

/* All of the device info needed for the spcp8x5 SIO serial converter */
static struct usb_serial_driver spcp8x5_device = {
	.driver = {
		.owner =	THIS_MODULE,
		.name =		"SPCP8x5",
	},
	.id_table		= id_table,
	.num_ports		= 1,
	.open 			= spcp8x5_open,
	.close 			= spcp8x5_close,
	.write 			= spcp8x5_write,
	.set_termios 		= spcp8x5_set_termios,
	.ioctl 			= spcp8x5_ioctl,
	.tiocmget 		= spcp8x5_tiocmget,
	.tiocmset 		= spcp8x5_tiocmset,
	.write_room 		= spcp8x5_write_room,
	.read_bulk_callback 	= spcp8x5_read_bulk_callback,
	.write_bulk_callback	= spcp8x5_write_bulk_callback,
	.chars_in_buffer 	= spcp8x5_chars_in_buffer,
	.attach 		= spcp8x5_startup,
	.shutdown 		= spcp8x5_shutdown,
};

static int __init spcp8x5_init(void)
{
	int retval;
	retval = usb_serial_register(&spcp8x5_device);
	if (retval)
		goto failed_usb_serial_register;
	retval = usb_register(&spcp8x5_driver);
	if (retval)
		goto failed_usb_register;
	info(DRIVER_DESC " " DRIVER_VERSION);
	return 0;
failed_usb_register:
	usb_serial_deregister(&spcp8x5_device);
failed_usb_serial_register:
	return retval;
}

static void __exit spcp8x5_exit(void)
{
	usb_deregister(&spcp8x5_driver);
	usb_serial_deregister(&spcp8x5_device);
}

module_init(spcp8x5_init);
module_exit(spcp8x5_exit);

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_VERSION(DRIVER_VERSION);
MODULE_LICENSE("GPL");

module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Debug enabled or not");