Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 | /*
* MPC8560ADS board specific routines
*
* Maintainer: Kumar Gala <galak@kernel.crashing.org>
*
* Copyright 2004 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/reboot.h>
#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/major.h>
#include <linux/console.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/root_dev.h>
#include <linux/serial.h>
#include <linux/tty.h> /* for linux/serial_core.h */
#include <linux/serial_core.h>
#include <linux/initrd.h>
#include <linux/module.h>
#include <linux/fsl_devices.h>
#include <linux/fs_enet_pd.h>
#include <asm/system.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/atomic.h>
#include <asm/time.h>
#include <asm/io.h>
#include <asm/machdep.h>
#include <asm/open_pic.h>
#include <asm/bootinfo.h>
#include <asm/pci-bridge.h>
#include <asm/mpc85xx.h>
#include <asm/irq.h>
#include <asm/immap_85xx.h>
#include <asm/kgdb.h>
#include <asm/ppc_sys.h>
#include <asm/cpm2.h>
#include <mm/mmu_decl.h>
#include <syslib/cpm2_pic.h>
#include <syslib/ppc85xx_common.h>
#include <syslib/ppc85xx_setup.h>
/* ************************************************************************
*
* Setup the architecture
*
*/
static void init_fcc_ioports(void)
{
struct immap *immap;
struct io_port *io;
u32 tempval;
immap = cpm2_immr;
io = &immap->im_ioport;
/* FCC2/3 are on the ports B/C. */
tempval = in_be32(&io->iop_pdirb);
tempval &= ~PB2_DIRB0;
tempval |= PB2_DIRB1;
out_be32(&io->iop_pdirb, tempval);
tempval = in_be32(&io->iop_psorb);
tempval &= ~PB2_PSORB0;
tempval |= PB2_PSORB1;
out_be32(&io->iop_psorb, tempval);
tempval = in_be32(&io->iop_pparb);
tempval |= (PB2_DIRB0 | PB2_DIRB1);
out_be32(&io->iop_pparb, tempval);
tempval = in_be32(&io->iop_pdirb);
tempval &= ~PB3_DIRB0;
tempval |= PB3_DIRB1;
out_be32(&io->iop_pdirb, tempval);
tempval = in_be32(&io->iop_psorb);
tempval &= ~PB3_PSORB0;
tempval |= PB3_PSORB1;
out_be32(&io->iop_psorb, tempval);
tempval = in_be32(&io->iop_pparb);
tempval |= (PB3_DIRB0 | PB3_DIRB1);
out_be32(&io->iop_pparb, tempval);
tempval = in_be32(&io->iop_pdirc);
tempval |= PC3_DIRC1;
out_be32(&io->iop_pdirc, tempval);
tempval = in_be32(&io->iop_pparc);
tempval |= PC3_DIRC1;
out_be32(&io->iop_pparc, tempval);
/* Port C has clocks...... */
tempval = in_be32(&io->iop_psorc);
tempval &= ~(CLK_TRX);
out_be32(&io->iop_psorc, tempval);
tempval = in_be32(&io->iop_pdirc);
tempval &= ~(CLK_TRX);
out_be32(&io->iop_pdirc, tempval);
tempval = in_be32(&io->iop_pparc);
tempval |= (CLK_TRX);
out_be32(&io->iop_pparc, tempval);
/* Configure Serial Interface clock routing.
* First, clear all FCC bits to zero,
* then set the ones we want.
*/
immap->im_cpmux.cmx_fcr &= ~(CPMUX_CLK_MASK);
immap->im_cpmux.cmx_fcr |= CPMUX_CLK_ROUTE;
}
static void __init
mpc8560ads_setup_arch(void)
{
bd_t *binfo = (bd_t *) __res;
unsigned int freq;
struct gianfar_platform_data *pdata;
struct gianfar_mdio_data *mdata;
struct fs_platform_info *fpi;
cpm2_reset();
/* get the core frequency */
freq = binfo->bi_intfreq;
if (ppc_md.progress)
ppc_md.progress("mpc8560ads_setup_arch()", 0);
/* Set loops_per_jiffy to a half-way reasonable value,
for use until calibrate_delay gets called. */
loops_per_jiffy = freq / HZ;
#ifdef CONFIG_PCI
/* setup PCI host bridges */
mpc85xx_setup_hose();
#endif
/* setup the board related info for the MDIO bus */
mdata = (struct gianfar_mdio_data *) ppc_sys_get_pdata(MPC85xx_MDIO);
mdata->irq[0] = MPC85xx_IRQ_EXT5;
mdata->irq[1] = MPC85xx_IRQ_EXT5;
mdata->irq[2] = PHY_POLL;
mdata->irq[3] = MPC85xx_IRQ_EXT5;
mdata->irq[31] = PHY_POLL;
/* setup the board related information for the enet controllers */
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC1);
if (pdata) {
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
pdata->bus_id = 0;
pdata->phy_id = 0;
memcpy(pdata->mac_addr, binfo->bi_enetaddr, 6);
}
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC2);
if (pdata) {
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
pdata->bus_id = 0;
pdata->phy_id = 1;
memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
}
init_fcc_ioports();
ppc_sys_device_remove(MPC85xx_CPM_FCC1);
fpi = (struct fs_platform_info *) ppc_sys_get_pdata(MPC85xx_CPM_FCC2);
if (fpi) {
memcpy(fpi->macaddr, binfo->bi_enet2addr, 6);
fpi->bus_id = "0:02";
fpi->phy_addr = 2;
fpi->dpram_offset = (u32)cpm2_immr->im_dprambase;
fpi->fcc_regs_c = (u32)&cpm2_immr->im_fcc_c[1];
}
fpi = (struct fs_platform_info *) ppc_sys_get_pdata(MPC85xx_CPM_FCC3);
if (fpi) {
memcpy(fpi->macaddr, binfo->bi_enet2addr, 6);
fpi->macaddr[5] += 1;
fpi->bus_id = "0:03";
fpi->phy_addr = 3;
fpi->dpram_offset = (u32)cpm2_immr->im_dprambase;
fpi->fcc_regs_c = (u32)&cpm2_immr->im_fcc_c[2];
}
#ifdef CONFIG_BLK_DEV_INITRD
if (initrd_start)
ROOT_DEV = Root_RAM0;
else
#endif
#ifdef CONFIG_ROOT_NFS
ROOT_DEV = Root_NFS;
#else
ROOT_DEV = Root_HDA1;
#endif
}
static irqreturn_t cpm2_cascade(int irq, void *dev_id)
{
while ((irq = cpm2_get_irq()) >= 0)
__do_IRQ(irq);
return IRQ_HANDLED;
}
static struct irqaction cpm2_irqaction = {
.handler = cpm2_cascade,
.flags = IRQF_DISABLED,
.mask = CPU_MASK_NONE,
.name = "cpm2_cascade",
};
static void __init
mpc8560_ads_init_IRQ(void)
{
/* Setup OpenPIC */
mpc85xx_ads_init_IRQ();
/* Setup CPM2 PIC */
cpm2_init_IRQ();
setup_irq(MPC85xx_IRQ_CPM, &cpm2_irqaction);
return;
}
/* ************************************************************************ */
void __init
platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
unsigned long r6, unsigned long r7)
{
/* parse_bootinfo must always be called first */
parse_bootinfo(find_bootinfo());
/*
* If we were passed in a board information, copy it into the
* residual data area.
*/
if (r3) {
memcpy((void *) __res, (void *) (r3 + KERNELBASE),
sizeof (bd_t));
}
#if defined(CONFIG_BLK_DEV_INITRD)
/*
* If the init RAM disk has been configured in, and there's a valid
* starting address for it, set it up.
*/
if (r4) {
initrd_start = r4 + KERNELBASE;
initrd_end = r5 + KERNELBASE;
}
#endif /* CONFIG_BLK_DEV_INITRD */
/* Copy the kernel command line arguments to a safe place. */
if (r6) {
*(char *) (r7 + KERNELBASE) = 0;
strcpy(cmd_line, (char *) (r6 + KERNELBASE));
}
identify_ppc_sys_by_id(mfspr(SPRN_SVR));
/* setup the PowerPC module struct */
ppc_md.setup_arch = mpc8560ads_setup_arch;
ppc_md.show_cpuinfo = mpc85xx_ads_show_cpuinfo;
ppc_md.init_IRQ = mpc8560_ads_init_IRQ;
ppc_md.get_irq = openpic_get_irq;
ppc_md.restart = mpc85xx_restart;
ppc_md.power_off = mpc85xx_power_off;
ppc_md.halt = mpc85xx_halt;
ppc_md.find_end_of_memory = mpc85xx_find_end_of_memory;
ppc_md.time_init = NULL;
ppc_md.set_rtc_time = NULL;
ppc_md.get_rtc_time = NULL;
ppc_md.calibrate_decr = mpc85xx_calibrate_decr;
if (ppc_md.progress)
ppc_md.progress("mpc8560ads_init(): exit", 0);
return;
}
|