Linux Audio

Check our new training course

Embedded Linux Audio

Check our new training course
with Creative Commons CC-BY-SA
lecture materials

Bootlin logo

Elixir Cross Referencer

Loading...
  1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524

                   Linux Ethernet Bonding Driver mini-howto

Initial release : Thomas Davis <tadavis at lbl.gov>
Corrections, HA extensions : 2000/10/03-15 :
  - Willy Tarreau <willy at meta-x.org>
  - Constantine Gavrilov <const-g at xpert.com>
  - Chad N. Tindel <ctindel at ieee dot org>
  - Janice Girouard <girouard at us dot ibm dot com>

Note :
------
The bonding driver originally came from Donald Becker's beowulf patches for
kernel 2.0. It has changed quite a bit since, and the original tools from
extreme-linux and beowulf sites will not work with this version of the driver.

For new versions of the driver, patches for older kernels and the updated
userspace tools, please follow the links at the end of this file.

Installation
============

1) Build kernel with the bonding driver
---------------------------------------
For the latest version of the bonding driver, use kernel 2.4.12 or above
(otherwise you will need to apply a patch).

Configure kernel with `make menuconfig/xconfig/config', and select
"Bonding driver support" in the "Network device support" section. It is
recommended to configure the driver as module since it is currently the only way
to pass parameters to the driver and configure more than one bonding device.

Build and install the new kernel and modules.

2) Get and install the userspace tools
--------------------------------------
This version of the bonding driver requires updated ifenslave program. The
original one from extreme-linux and beowulf will not work. Kernels 2.4.12
and above include the updated version of ifenslave.c in Documentation/network
directory. For older kernels, please follow the links at the end of this file.

IMPORTANT!!!  If you are running on Redhat 7.1 or greater, you need
to be careful because /usr/include/linux is no longer a symbolic link
to /usr/src/linux/include/linux.  If you build ifenslave while this is
true, ifenslave will appear to succeed but your bond won't work.  The purpose
of the -I option on the ifenslave compile line is to make sure it uses
/usr/src/linux/include/linux/if_bonding.h instead of the version from
/usr/include/linux.

To install ifenslave.c, do:
    # gcc -Wall -Wstrict-prototypes -O -I/usr/src/linux/include ifenslave.c -o ifenslave 
    # cp ifenslave /sbin/ifenslave

3) Configure your system
------------------------
Also see the following section on the module parameters. You will need to add
at least the following line to /etc/conf.modules (or /etc/modules.conf):

	alias bond0 bonding

Use standard distribution techniques to define bond0 network interface. For
example, on modern RedHat distributions, create ifcfg-bond0 file in
/etc/sysconfig/network-scripts directory that looks like this:

DEVICE=bond0
IPADDR=192.168.1.1
NETMASK=255.255.255.0
NETWORK=192.168.1.0
BROADCAST=192.168.1.255
ONBOOT=yes
BOOTPROTO=none
USERCTL=no

(put the appropriate values for you network instead of 192.168.1).

All interfaces that are part of the trunk, should have SLAVE and MASTER
definitions. For example, in the case of RedHat, if you wish to make eth0 and
eth1 (or other interfaces) a part of the bonding interface bond0, their config
files (ifcfg-eth0, ifcfg-eth1, etc.) should look like this:

DEVICE=eth0
USERCTL=no
ONBOOT=yes
MASTER=bond0
SLAVE=yes
BOOTPROTO=none

(use DEVICE=eth1 for eth1 and MASTER=bond1 for bond1 if you have configured
second bonding interface). 

Restart the networking subsystem or just bring up the bonding device if your
administration tools allow it. Otherwise, reboot. (For the case of RedHat
distros, you can do `ifup bond0' or `/etc/rc.d/init.d/network restart'.)

If the administration tools of your distribution do not support master/slave
notation in configuration of network interfaces, you will need to configure
the bonding device with the following commands manually:

    # /sbin/ifconfig bond0 192.168.1.1 up
    # /sbin/ifenslave bond0 eth0
    # /sbin/ifenslave bond0 eth1

(substitute 192.168.1.1 with your IP address and add custom network and custom
netmask to the arguments of ifconfig if required).

You can then create a script with these commands and put it into the appropriate
rc directory.

If you specifically need that all your network drivers are loaded before the
bonding driver, use one of modutils' powerful features : in your modules.conf,
tell that when asked for bond0, modprobe should first load all your interfaces :

probeall bond0 eth0 eth1 bonding

Be careful not to reference bond0 itself at the end of the line, or modprobe will
die in an endless recursive loop.

4) Module parameters.
---------------------
The following module parameters can be passed:

    mode=

Possible values are 0 (round robin policy, default) and 1 (active backup
policy), and 2 (XOR).  See question 9 and the HA section for additional info.

    miimon=

Use integer value for the frequency (in ms) of MII link monitoring. Zero value
is default and means the link monitoring will be disabled. A good value is 100
if you wish to use link monitoring. See HA section for additional info.

    downdelay=

Use integer value for delaying disabling a link by this number (in ms) after
the link failure has been detected. Must be a multiple of miimon. Default
value is zero. See HA section for additional info.

    updelay=

Use integer value for delaying enabling a link by this number (in ms) after
the "link up" status has been detected. Must be a multiple of miimon. Default
value is zero. See HA section for additional info.

    arp_interval=

Use integer value for the frequency (in ms) of arp monitoring.  Zero value 
is default and means the arp monitoring will be disabled.  See HA section
for additional info.   This field is value in active_backup mode only.

    arp_ip_target=

An ip address to use when arp_interval is > 0.  This is the target of the
arp request sent to determine the health of the link to the target.  
Specify this value in ddd.ddd.ddd.ddd format.

If you need to configure several bonding devices, the driver must be loaded
several times. I.e. for two bonding devices, your /etc/conf.modules must look
like this:

alias bond0 bonding
alias bond1 bonding

options bond0 miimon=100
options bond1 -o bonding1 miimon=100

5) Testing configuration
------------------------
You can test the configuration and transmit policy with ifconfig. For example,
for round robin policy, you should get something like this:

[root]# /sbin/ifconfig
bond0     Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4  
          inet addr:XXX.XXX.XXX.YYY  Bcast:XXX.XXX.XXX.255  Mask:255.255.252.0
          UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
          RX packets:7224794 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3286647 errors:1 dropped:0 overruns:1 carrier:0
          collisions:0 txqueuelen:0 

eth0      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4  
          inet addr:XXX.XXX.XXX.YYY  Bcast:XXX.XXX.XXX.255  Mask:255.255.252.0
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:3573025 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1643167 errors:1 dropped:0 overruns:1 carrier:0
          collisions:0 txqueuelen:100 
          Interrupt:10 Base address:0x1080 

eth1      Link encap:Ethernet  HWaddr 00:C0:F0:1F:37:B4  
          inet addr:XXX.XXX.XXX.YYY  Bcast:XXX.XXX.XXX.255  Mask:255.255.252.0
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:3651769 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1643480 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          Interrupt:9 Base address:0x1400 

Questions :
===========

1.  Is it SMP safe?

	Yes.  The old 2.0.xx channel bonding patch was not SMP safe.
	The new driver was designed to be SMP safe from the start.

2.  What type of cards will work with it?

	Any Ethernet type cards (you can even mix cards - a Intel
	EtherExpress PRO/100 and a 3com 3c905b, for example).
	You can even bond together Gigabit Ethernet cards!

3.  How many bonding devices can I have?

	One for each module you load. See section on module parameters for how
	to accomplish this.

4.  How many slaves can a bonding device have?

	Limited by the number of network interfaces Linux supports and the
	number of cards you can place in your system.

5.  What happens when a slave link dies?

	If your ethernet cards support MII status monitoring and the MII
	monitoring has been enabled in the driver (see description of module
	parameters), there will be no adverse consequences. This release
	of the bonding driver knows how to get the MII information and
	enables or disables its slaves according to their link status.
	See section on HA for additional information.

	For ethernet cards not supporting MII status, or if you wish to 
	verify that packets have been both send and received, you may
	configure the arp_interval and arp_ip_target.  If packets have
	not been sent or received during this interval, an arp request
	is sent to the target to generate send and receive traffic.  
	If after this interval, either the successful send and/or 
	receive count has not incremented, the next slave in the sequence
	will become the active slave.

	If neither mii_monitor and arp_interval is configured, the bonding
	driver will not handle this situation very well. The driver will 
	continue to send packets but some packets will be lost. Retransmits 
	will cause serious degradation of performance (in the case when one
	of two slave links fails, 50% packets will be lost, which is a serious
	problem for both TCP and UDP).

6.  Can bonding be used for High Availability?

	Yes, if you use MII monitoring and ALL your cards support MII link
	status reporting. See section on HA for more information.

7.  Which switches/systems does it work with?

	In round-robin mode, it works with systems that support trunking:
	
	* Cisco 5500 series (look for EtherChannel support).
	* SunTrunking software.
	* Alteon AceDirector switches / WebOS (use Trunks).
	* BayStack Switches (trunks must be explicitly configured). Stackable
	  models (450) can define trunks between ports on different physical
	  units.
	* Linux bonding, of course !
	
	In Active-backup mode, it should work with any Layer-II switches.

8.  Where does a bonding device get its MAC address from?

	If not explicitly configured with ifconfig, the MAC address of the
	bonding device is taken from its first slave device. This MAC address
	is then passed to all following slaves and remains persistent (even if
	the first slave is removed) until the bonding device is brought
	down or reconfigured.
	
	If you wish to change the MAC address, you can set it with ifconfig:

	  # ifconfig bond0 hw ether 00:11:22:33:44:55

	The MAC address can be also changed by bringing down/up the device
	and then changing its slaves (or their order):
	
	  # ifconfig bond0 down ; modprobe -r bonding
	  # ifconfig bond0 .... up
	  # ifenslave bond0 eth...

	This method will automatically take the address from the next slave
	that will be added.
	
	To restore your slaves' MAC addresses, you need to detach them
	from the bond (`ifenslave -d bond0 eth0'), set them down
	(`ifconfig eth0 down'), unload the drivers (`rmmod 3c59x', for
	example) and reload them to get the MAC addresses from their
	eeproms. If the driver is shared by several devices, you need
	to turn them all down. Another solution is to look for the MAC
	address at boot time (dmesg or tail /var/log/messages) and to
	reset it by hand with ifconfig :

	  # ifconfig eth0 down
	  # ifconfig eth0 hw ether 00:20:40:60:80:A0

9.  Which transmit polices can be used?

	Round robin, based on the order of enslaving, the output device
	is selected base on the next available slave.  Regardless of
	the source and/or destination of the packet.

	XOR, based on (src hw addr XOR dst hw addr) % slave cnt.  This
	selects the same slave for each destination hw address.

	Active-backup policy that ensures that one and only one device will
	transmit at any given moment. Active-backup policy is useful for
	implementing high availability solutions using two hubs (see
	section on HA).

High availability
=================

To implement high availability using the bonding driver, you need to
compile the driver as module because currently it is the only way to pass
parameters to the driver. This may change in the future.

High availability is achieved by using MII status reporting. You need to
verify that all your interfaces support MII link status reporting. On Linux
kernel 2.2.17, all the 100 Mbps capable drivers and yellowfin gigabit driver
support it. If your system has an interface that does not support MII status
reporting, a failure of its link will not be detected!

The bonding driver can regularly check all its slaves links by checking the
MII status registers. The check interval is specified by the module argument
"miimon" (MII monitoring). It takes an integer that represents the
checking time in milliseconds. It should not come to close to (1000/HZ)
(10 ms on i386) because it may then reduce the system interactivity. 100 ms
seems to be a good value. It means that a dead link will be detected at most
100 ms after it goes down.

Example:

   # modprobe bonding miimon=100

Or, put in your /etc/modules.conf :

   alias bond0 bonding
   options bond0 miimon=100

There are currently two policies for high availability, depending on whether
a) hosts are connected to a single host or switch that support trunking
b) hosts are connected to several different switches or a single switch that
   does not support trunking.

1) HA on a single switch or host - load balancing
-------------------------------------------------
It is the easiest to set up and to understand. Simply configure the
remote equipment (host or switch) to aggregate traffic over several
ports (Trunk, EtherChannel, etc.) and configure the bonding interfaces.
If the module has been loaded with the proper MII option, it will work
automatically. You can then try to remove and restore different links
and see in your logs what the driver detects. When testing, you may
encounter problems on some buggy switches that disable the trunk for a
long time if all ports in a trunk go down. This is not Linux, but really
the switch (reboot it to ensure).

Example 1 : host to host at double speed

          +----------+                          +----------+
          |          |eth0                  eth0|          |
          | Host A   +--------------------------+  Host B  |
          |          +--------------------------+          |
          |          |eth1                  eth1|          |
          +----------+                          +----------+

  On each host :
     # modprobe bonding miimon=100
     # ifconfig bond0 addr
     # ifenslave bond0 eth0 eth1

Example 2 : host to switch at double speed

          +----------+                          +----------+
          |          |eth0                 port1|          |
          | Host A   +--------------------------+  switch  |
          |          +--------------------------+          |
          |          |eth1                 port2|          |
          +----------+                          +----------+

  On host A :                             On the switch :
     # modprobe bonding miimon=100           # set up a trunk on port1
     # ifconfig bond0 addr                     and port2
     # ifenslave bond0 eth0 eth1

2) HA on two or more switches (or a single switch without trunking support)
---------------------------------------------------------------------------
This mode is more problematic because it relies on the fact that there
are multiple ports and the host's MAC address should be visible on one
port only to avoid confusing the switches.

If you need to know which interface is the active one, and which ones are
backup, use ifconfig. All backup interfaces have the NOARP flag set.

To use this mode, pass "mode=1" to the module at load time :

    # modprobe bonding miimon=100 mode=1

Or, put in your /etc/modules.conf :

    alias bond0 bonding
    options bond0 miimon=100 mode=1

Example 1: Using multiple host and multiple switches to build a "no single
point of failure" solution.


                |                                     |
                |port3                           port3|
          +-----+----+                          +-----+----+
          |          |port7       ISL      port7|          |
          | switch A +--------------------------+ switch B |
          |          +--------------------------+          |
          |          |port8                port8|          |
          +----++----+                          +-----++---+
          port2||port1                           port1||port2
               ||             +-------+               ||
               |+-------------+ host1 +---------------+|
               |         eth0 +-------+ eth1           |
               |                                       |
               |              +-------+                |
               +--------------+ host2 +----------------+
                         eth0 +-------+ eth1

In this configuration, there are an ISL - Inter Switch Link (could be a trunk),
several servers (host1, host2 ...) attached to both switches each, and one or
more ports to the outside world (port3...). One an only one slave on each host
is active at a time, while all links are still monitored (the system can
detect a failure of active and backup links).

Each time a host changes its active interface, it sticks to the new one until
it goes down. In this example, the hosts are not too much affected by the
expiration time of the switches' forwarding tables.

If host1 and host2 have the same functionality and are used in load balancing
by another external mechanism, it is good to have host1's active interface
connected to one switch and host2's to the other. Such system will survive
a failure of a single host, cable, or switch. The worst thing that may happen
in the case of a switch failure is that half of the hosts will be temporarily
unreachable until the other switch expires its tables. 

Example 2: Using multiple ethernet cards connected to a switch to configure
           NIC failover (switch is not required to support trunking). 


          +----------+                          +----------+
          |          |eth0                 port1|          |
          | Host A   +--------------------------+  switch  |
          |          +--------------------------+          |
          |          |eth1                 port2|          |
          +----------+                          +----------+

  On host A :                                 On the switch :
     # modprobe bonding miimon=100 mode=1     # (optional) minimize the time
     # ifconfig bond0 addr                    # for table expiration
     # ifenslave bond0 eth0 eth1

Each time the host changes its active interface, it sticks to the new one until
it goes down. In this example, the host is strongly affected by the expiration
time of the switch forwarding table.

3) Adapting to your switches' timing
------------------------------------
If your switches take a long time to go into backup mode, it may be
desirable not to activate a backup interface immediately after a link goes
down. It is possible to delay the moment at which a link will be
completely disabled by passing the module parameter "downdelay" (in
milliseconds, must be a multiple of miimon).

When a switch reboots, it is possible that its ports report "link up" status
before they become usable. This could fool a bond device by causing it to
use some ports that are not ready yet. It is possible to delay the moment at
which an active link will be reused by passing the module parameter "updelay"
(in milliseconds, must be a multiple of miimon).

A similar situation can occur when a host re-negotiates a lost link with the
switch (a case of cable replacement).

A special case is when a bonding interface has lost all slave links. Then the
driver will immediately reuse the first link that goes up, even if updelay
parameter was specified. (If there are slave interfaces in the "updelay" state,
the interface that first went into that state will be immediately reused.) This
allows to reduce down-time if the value of updelay has been overestimated.

Examples :

    # modprobe bonding miimon=100 mode=1 downdelay=2000 updelay=5000
    # modprobe bonding miimon=100 mode=0 downdelay=0 updelay=5000

4) Limitations
--------------
The main limitations are :
  - only the link status is monitored. If the switch on the other side is
    partially down (e.g. doesn't forward anymore, but the link is OK), the link
    won't be disabled. Another way to check for a dead link could be to count
    incoming frames on a heavily loaded host. This is not applicable to small
    servers, but may be useful when the front switches send multicast
    information on their links (e.g. VRRP), or even health-check the servers.
    Use the arp_interval/arp_ip_target parameters to count incoming/outgoing
    frames.  

Resources and links
===================

Current development on this driver is posted to:
 - http://www.sourceforge.net/projects/bonding/

Donald Becker's Ethernet Drivers and diag programs may be found at :
 - http://www.scyld.com/network/

You will also find a lot of information regarding Ethernet, NWay, MII, etc. at
www.scyld.com.

For new versions of the driver, patches for older kernels and the updated
userspace tools, take a look at Willy Tarreau's site :
 - http://wtarreau.free.fr/pub/bonding/
 - http://www-miaif.lip6.fr/willy/pub/bonding/

To get latest informations about Linux Kernel development, please consult
the Linux Kernel Mailing List Archives at :
   http://boudicca.tux.org/hypermail/linux-kernel/latest/

-- END --