/*
 *  linux/drivers/block/ide.c	Version 6.18  August 16, 1998
 *
 *  Copyright (C) 1994-1998  Linus Torvalds & authors (see below)
 */

/*
 *  Mostly written by Mark Lord  <mlord@pobox.com>
 *                and Gadi Oxman <gadio@netvision.net.il>
 *
 *  See linux/MAINTAINERS for address of current maintainer.
 *
 * This is the multiple IDE interface driver, as evolved from hd.c.
 * It supports up to MAX_HWIFS IDE interfaces, on one or more IRQs (usually 14 & 15).
 * There can be up to two drives per interface, as per the ATA-2 spec.
 *
 * Primary:    ide0, port 0x1f0; major=3;  hda is minor=0; hdb is minor=64
 * Secondary:  ide1, port 0x170; major=22; hdc is minor=0; hdd is minor=64
 * Tertiary:   ide2, port 0x???; major=33; hde is minor=0; hdf is minor=64
 * Quaternary: ide3, port 0x???; major=34; hdg is minor=0; hdh is minor=64
 * ...
 *
 *  From hd.c:
 *  |
 *  | It traverses the request-list, using interrupts to jump between functions.
 *  | As nearly all functions can be called within interrupts, we may not sleep.
 *  | Special care is recommended.  Have Fun!
 *  |
 *  | modified by Drew Eckhardt to check nr of hd's from the CMOS.
 *  |
 *  | Thanks to Branko Lankester, lankeste@fwi.uva.nl, who found a bug
 *  | in the early extended-partition checks and added DM partitions.
 *  |
 *  | Early work on error handling by Mika Liljeberg (liljeber@cs.Helsinki.FI).
 *  |
 *  | IRQ-unmask, drive-id, multiple-mode, support for ">16 heads",
 *  | and general streamlining by Mark Lord (mlord@pobox.com).
 *
 *  October, 1994 -- Complete line-by-line overhaul for linux 1.1.x, by:
 *
 *	Mark Lord	(mlord@pobox.com)		(IDE Perf.Pkg)
 *	Delman Lee	(delman@mipg.upenn.edu)		("Mr. atdisk2")
 *	Scott Snyder	(snyder@fnald0.fnal.gov)	(ATAPI IDE cd-rom)
 *
 *  This was a rewrite of just about everything from hd.c, though some original
 *  code is still sprinkled about.  Think of it as a major evolution, with
 *  inspiration from lots of linux users, esp.  hamish@zot.apana.org.au
 *
 *  Version 1.0 ALPHA	initial code, primary i/f working okay
 *  Version 1.3 BETA	dual i/f on shared irq tested & working!
 *  Version 1.4 BETA	added auto probing for irq(s)
 *  Version 1.5 BETA	added ALPHA (untested) support for IDE cd-roms,
 *  ...
 * Version 5.50		allow values as small as 20 for idebus=
 * Version 5.51		force non io_32bit in drive_cmd_intr()
 *			change delay_10ms() to delay_50ms() to fix problems
 * Version 5.52		fix incorrect invalidation of removable devices
 *			add "hdx=slow" command line option
 * Version 5.60		start to modularize the driver; the disk and ATAPI
 *			 drivers can be compiled as loadable modules.
 *			move IDE probe code to ide-probe.c
 *			move IDE disk code to ide-disk.c
 *			add support for generic IDE device subdrivers
 *			add m68k code from Geert Uytterhoeven
 *			probe all interfaces by default
 *			add ioctl to (re)probe an interface
 * Version 6.00		use per device request queues
 *			attempt to optimize shared hwgroup performance
 *			add ioctl to manually adjust bandwidth algorithms
 *			add kerneld support for the probe module
 *			fix bug in ide_error()
 *			fix bug in the first ide_get_lock() call for Atari
 *			don't flush leftover data for ATAPI devices
 * Version 6.01		clear hwgroup->active while the hwgroup sleeps
 *			support HDIO_GETGEO for floppies
 * Version 6.02		fix ide_ack_intr() call
 *			check partition table on floppies
 * Version 6.03		handle bad status bit sequencing in ide_wait_stat()
 * Version 6.10		deleted old entries from this list of updates
 *			replaced triton.c with ide-dma.c generic PCI DMA
 *			added support for BIOS-enabled UltraDMA
 *			rename all "promise" things to "pdc4030"
 *			fix EZ-DRIVE handling on small disks
 * Version 6.11		fix probe error in ide_scan_devices()
 *			fix ancient "jiffies" polling bugs
 *			mask all hwgroup interrupts on each irq entry
 * Version 6.12		integrate ioctl and proc interfaces
 *			fix parsing of "idex=" command line parameter
 * Version 6.13		add support for ide4/ide5 courtesy rjones@orchestream.com
 * Version 6.14		fixed IRQ sharing among PCI devices
 * Version 6.15		added SMP awareness to IDE drivers
 * Version 6.16		fixed various bugs; even more SMP friendly
 * Version 6.17		fix for newest EZ-Drive problem
 * Version 6.18		default unpartitioned-disk translation now "BIOS LBA"
 *
 *  Some additional driver compile-time options are in ide.h
 *
 *  To do, in likely order of completion:
 *	- modify kernel to obtain BIOS geometry for drives on 2nd/3rd/4th i/f
*/

#undef REALLY_SLOW_IO		/* most systems can safely undef this */

#define _IDE_C			/* Tell ide.h it's really us */

#include <linux/config.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/interrupt.h>
#include <linux/major.h>
#include <linux/errno.h>
#include <linux/genhd.h>
#include <linux/malloc.h>
#include <linux/pci.h>
#include <linux/delay.h>

#include <asm/byteorder.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/bitops.h>

#include "ide.h"
#include "ide_modes.h"

#ifdef CONFIG_KMOD
#include <linux/kmod.h>
#endif /* CONFIG_KMOD */

static const byte	ide_hwif_to_major[] = {IDE0_MAJOR, IDE1_MAJOR, IDE2_MAJOR, IDE3_MAJOR, IDE4_MAJOR, IDE5_MAJOR };

static int	idebus_parameter; /* holds the "idebus=" parameter */
static int	system_bus_speed; /* holds what we think is VESA/PCI bus speed */
static int	initializing;     /* set while initializing built-in drivers */

/*
 * ide_lock is used by the Atari code to obtain access to the IDE interrupt,
 * which is shared between several drivers.
 */
static int	ide_lock = 0;

/*
 * ide_modules keeps track of the available IDE chipset/probe/driver modules.
 */
ide_module_t *ide_modules = NULL;

/*
 * This is declared extern in ide.h, for access by other IDE modules:
 */
ide_hwif_t	ide_hwifs[MAX_HWIFS];	/* master data repository */

#if (DISK_RECOVERY_TIME > 0)
/*
 * For really screwy hardware (hey, at least it *can* be used with Linux)
 * we can enforce a minimum delay time between successive operations.
 */
static unsigned long read_timer(void)
{
	unsigned long t, flags;
	int i;

	__save_flags(flags);	/* local CPU only */
	__cli();		/* local CPU only */
	t = jiffies * 11932;
    	outb_p(0, 0x43);
	i = inb_p(0x40);
	i |= inb(0x40) << 8;
	__restore_flags(flags);	/* local CPU only */
	return (t - i);
}
#endif /* DISK_RECOVERY_TIME */

static inline void set_recovery_timer (ide_hwif_t *hwif)
{
#if (DISK_RECOVERY_TIME > 0)
	hwif->last_time = read_timer();
#endif /* DISK_RECOVERY_TIME */
}

/*
 * Do not even *think* about calling this!
 */
static void init_hwif_data (unsigned int index)
{
	unsigned int unit;
	ide_hwif_t *hwif = &ide_hwifs[index];

	/* bulk initialize hwif & drive info with zeros */
	memset(hwif, 0, sizeof(ide_hwif_t));

	/* fill in any non-zero initial values */
	hwif->index     = index;
	ide_init_hwif_ports(hwif->io_ports, ide_default_io_base(index), &hwif->irq);
	hwif->noprobe	= !hwif->io_ports[IDE_DATA_OFFSET];
#ifdef CONFIG_BLK_DEV_HD
	if (hwif->io_ports[IDE_DATA_OFFSET] == HD_DATA)
		hwif->noprobe = 1; /* may be overridden by ide_setup() */
#endif /* CONFIG_BLK_DEV_HD */
	hwif->major	= ide_hwif_to_major[index];
	hwif->name[0]	= 'i';
	hwif->name[1]	= 'd';
	hwif->name[2]	= 'e';
	hwif->name[3]	= '0' + index;
	for (unit = 0; unit < MAX_DRIVES; ++unit) {
		ide_drive_t *drive = &hwif->drives[unit];

		drive->media			= ide_disk;
		drive->select.all		= (unit<<4)|0xa0;
		drive->hwif			= hwif;
		drive->ctl			= 0x08;
		drive->ready_stat		= READY_STAT;
		drive->bad_wstat		= BAD_W_STAT;
		drive->special.b.recalibrate	= 1;
		drive->special.b.set_geometry	= 1;
		drive->name[0]			= 'h';
		drive->name[1]			= 'd';
		drive->name[2]			= 'a' + (index * MAX_DRIVES) + unit;
	}
}

/*
 * init_ide_data() sets reasonable default values into all fields
 * of all instances of the hwifs and drives, but only on the first call.
 * Subsequent calls have no effect (they don't wipe out anything).
 *
 * This routine is normally called at driver initialization time,
 * but may also be called MUCH earlier during kernel "command-line"
 * parameter processing.  As such, we cannot depend on any other parts
 * of the kernel (such as memory allocation) to be functioning yet.
 *
 * This is too bad, as otherwise we could dynamically allocate the
 * ide_drive_t structs as needed, rather than always consuming memory
 * for the max possible number (MAX_HWIFS * MAX_DRIVES) of them.
 */
#define MAGIC_COOKIE 0x12345678
static void init_ide_data (void)
{
	unsigned int index;
	static unsigned long magic_cookie = MAGIC_COOKIE;

	if (magic_cookie != MAGIC_COOKIE)
		return;		/* already initialized */
	magic_cookie = 0;

	for (index = 0; index < MAX_HWIFS; ++index)
		init_hwif_data(index);

	idebus_parameter = 0;
	system_bus_speed = 0;
}

/*
 * ide_system_bus_speed() returns what we think is the system VESA/PCI
 * bus speed (in MHz).  This is used for calculating interface PIO timings.
 * The default is 40 for known PCI systems, 50 otherwise.
 * The "idebus=xx" parameter can be used to override this value.
 * The actual value to be used is computed/displayed the first time through.
 */
int ide_system_bus_speed (void)
{
	if (!system_bus_speed) {
		if (idebus_parameter)
			system_bus_speed = idebus_parameter;	/* user supplied value */
#ifdef CONFIG_PCI
		else if (pci_present())
			system_bus_speed = 40;	/* safe default value for PCI */
#endif /* CONFIG_PCI */
		else
			system_bus_speed = 50;	/* safe default value for VESA and PCI */
		printk("ide: Assuming %dMHz system bus speed for PIO modes%s\n", system_bus_speed,
			idebus_parameter ? "" : "; override with idebus=xx");
	}
	return system_bus_speed;
}

#if SUPPORT_VLB_SYNC
/*
 * Some localbus EIDE interfaces require a special access sequence
 * when using 32-bit I/O instructions to transfer data.  We call this
 * the "vlb_sync" sequence, which consists of three successive reads
 * of the sector count register location, with interrupts disabled
 * to ensure that the reads all happen together.
 */
static inline void do_vlb_sync (ide_ioreg_t port) {
	(void) inb (port);
	(void) inb (port);
	(void) inb (port);
}
#endif /* SUPPORT_VLB_SYNC */

/*
 * This is used for most PIO data transfers *from* the IDE interface
 */
void ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
{
	byte io_32bit = drive->io_32bit;

	if (io_32bit) {
#if SUPPORT_VLB_SYNC
		if (io_32bit & 2) {
			unsigned long flags;
			__save_flags(flags);	/* local CPU only */
			__cli();		/* local CPU only */
			do_vlb_sync(IDE_NSECTOR_REG);
			insl(IDE_DATA_REG, buffer, wcount);
			__restore_flags(flags);	/* local CPU only */
		} else
#endif /* SUPPORT_VLB_SYNC */
			insl(IDE_DATA_REG, buffer, wcount);
	} else {
#if SUPPORT_SLOW_DATA_PORTS
		if (drive->slow) {
			unsigned short *ptr = (unsigned short *) buffer;
			while (wcount--) {
				*ptr++ = inw_p(IDE_DATA_REG);
				*ptr++ = inw_p(IDE_DATA_REG);
			}
		} else
#endif /* SUPPORT_SLOW_DATA_PORTS */
			insw(IDE_DATA_REG, buffer, wcount<<1);
	}
}

/*
 * This is used for most PIO data transfers *to* the IDE interface
 */
void ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
{
	byte io_32bit = drive->io_32bit;

	if (io_32bit) {
#if SUPPORT_VLB_SYNC
		if (io_32bit & 2) {
			unsigned long flags;
			__save_flags(flags);	/* local CPU only */
			__cli();		/* local CPU only */
			do_vlb_sync(IDE_NSECTOR_REG);
			outsl(IDE_DATA_REG, buffer, wcount);
			__restore_flags(flags);	/* local CPU only */
		} else
#endif /* SUPPORT_VLB_SYNC */
			outsl(IDE_DATA_REG, buffer, wcount);
	} else {
#if SUPPORT_SLOW_DATA_PORTS
		if (drive->slow) {
			unsigned short *ptr = (unsigned short *) buffer;
			while (wcount--) {
				outw_p(*ptr++, IDE_DATA_REG);
				outw_p(*ptr++, IDE_DATA_REG);
			}
		} else
#endif /* SUPPORT_SLOW_DATA_PORTS */
			outsw(IDE_DATA_REG, buffer, wcount<<1);
	}
}

/*
 * The following routines are mainly used by the ATAPI drivers.
 *
 * These routines will round up any request for an odd number of bytes,
 * so if an odd bytecount is specified, be sure that there's at least one
 * extra byte allocated for the buffer.
 */
void atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount)
{
	++bytecount;
#ifdef CONFIG_ATARI
	if (MACH_IS_ATARI) {
		/* Atari has a byte-swapped IDE interface */
		insw_swapw(IDE_DATA_REG, buffer, bytecount / 2);
		return;
	}
#endif /* CONFIG_ATARI */
	ide_input_data (drive, buffer, bytecount / 4);
	if ((bytecount & 0x03) >= 2)
		insw (IDE_DATA_REG, ((byte *)buffer) + (bytecount & ~0x03), 1);
}

void atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount)
{
	++bytecount;
#ifdef CONFIG_ATARI
	if (MACH_IS_ATARI) {
		/* Atari has a byte-swapped IDE interface */
		outsw_swapw(IDE_DATA_REG, buffer, bytecount / 2);
		return;
	}
#endif /* CONFIG_ATARI */
	ide_output_data (drive, buffer, bytecount / 4);
	if ((bytecount & 0x03) >= 2)
		outsw (IDE_DATA_REG, ((byte *)buffer) + (bytecount & ~0x03), 1);
}

/*
 * Needed for PCI irq sharing
 */
static inline int drive_is_ready (ide_drive_t *drive)
{
	if (drive->waiting_for_dma)
		return HWIF(drive)->dmaproc(ide_dma_test_irq, drive);
#if 0
	udelay(1);	/* need to guarantee 400ns since last command was issued */
#endif
	if (GET_STAT() & BUSY_STAT)
		return 0;	/* drive busy:  definitely not interrupting */
	return 1;		/* drive ready: *might* be interrupting */
}

/*
 * This is our end_request replacement function.
 */
void ide_end_request(byte uptodate, ide_hwgroup_t *hwgroup)
{
	struct request *rq;
	unsigned long flags;

	spin_lock_irqsave(&io_request_lock, flags);
	rq = hwgroup->rq;

	if (!end_that_request_first(rq, uptodate, hwgroup->drive->name)) {
		add_blkdev_randomness(MAJOR(rq->rq_dev));
		hwgroup->drive->queue = rq->next;
        	blk_dev[MAJOR(rq->rq_dev)].current_request = NULL;
        	hwgroup->rq = NULL;
		end_that_request_last(rq);
	}
	spin_unlock_irqrestore(&io_request_lock, flags);
}

/*
 * This should get invoked any time we exit the driver to
 * wait for an interrupt response from a drive.  handler() points
 * at the appropriate code to handle the next interrupt, and a
 * timer is started to prevent us from waiting forever in case
 * something goes wrong (see the ide_timer_expiry() handler later on).
 */
void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout)
{
	unsigned long flags;
	ide_hwgroup_t *hwgroup = HWGROUP(drive);

	spin_lock_irqsave(&hwgroup->spinlock, flags);
#ifdef DEBUG
	if (hwgroup->handler != NULL) {
		printk("%s: ide_set_handler: handler not null; old=%p, new=%p\n",
			drive->name, hwgroup->handler, handler);
	}
#endif
	hwgroup->handler       = handler;
	hwgroup->timer.expires = jiffies + timeout;
	add_timer(&(hwgroup->timer));
	spin_unlock_irqrestore(&hwgroup->spinlock, flags);
}

/*
 * current_capacity() returns the capacity (in sectors) of a drive
 * according to its current geometry/LBA settings.
 */
static unsigned long current_capacity (ide_drive_t *drive)
{
	if (!drive->present)
		return 0;
	if (drive->driver != NULL)
		return DRIVER(drive)->capacity(drive);
	return 0;
}

/*
 * ide_geninit() is called exactly *once* for each major, from genhd.c,
 * at the beginning of the initial partition check for the drives.
 */
void ide_geninit (struct gendisk *gd)
{
	unsigned int unit;
	ide_hwif_t *hwif = gd->real_devices;

	for (unit = 0; unit < gd->nr_real; ++unit) {
		ide_drive_t *drive = &hwif->drives[unit];

		drive->part[0].nr_sects = current_capacity(drive);
		if (!drive->present || (drive->media != ide_disk && drive->media != ide_floppy) ||
		    drive->driver == NULL || !drive->part[0].nr_sects)
			drive->part[0].start_sect = -1; /* skip partition check */
	}
}

static void do_reset1 (ide_drive_t *, int);		/* needed below */

/*
 * atapi_reset_pollfunc() gets invoked to poll the interface for completion every 50ms
 * during an atapi drive reset operation. If the drive has not yet responded,
 * and we have not yet hit our maximum waiting time, then the timer is restarted
 * for another 50ms.
 */
static void atapi_reset_pollfunc (ide_drive_t *drive)
{
	ide_hwgroup_t *hwgroup = HWGROUP(drive);
	byte stat;

	SELECT_DRIVE(HWIF(drive),drive);
	udelay (10);

	if (OK_STAT(stat=GET_STAT(), 0, BUSY_STAT)) {
		printk("%s: ATAPI reset complete\n", drive->name);
	} else {
		if (0 < (signed long)(hwgroup->poll_timeout - jiffies)) {
			ide_set_handler (drive, &atapi_reset_pollfunc, HZ/20);
			return;	/* continue polling */
		}
		hwgroup->poll_timeout = 0;	/* end of polling */
		printk("%s: ATAPI reset timed-out, status=0x%02x\n", drive->name, stat);
		do_reset1 (drive, 1);	/* do it the old fashioned way */
		return;
	}
	hwgroup->poll_timeout = 0;	/* done polling */
}

/*
 * reset_pollfunc() gets invoked to poll the interface for completion every 50ms
 * during an ide reset operation. If the drives have not yet responded,
 * and we have not yet hit our maximum waiting time, then the timer is restarted
 * for another 50ms.
 */
static void reset_pollfunc (ide_drive_t *drive)
{
	ide_hwgroup_t *hwgroup = HWGROUP(drive);
	ide_hwif_t *hwif = HWIF(drive);
	byte tmp;

	if (!OK_STAT(tmp=GET_STAT(), 0, BUSY_STAT)) {
		if (0 < (signed long)(hwgroup->poll_timeout - jiffies)) {
			ide_set_handler (drive, &reset_pollfunc, HZ/20);
			return;	/* continue polling */
		}
		printk("%s: reset timed-out, status=0x%02x\n", hwif->name, tmp);
	} else  {
		printk("%s: reset: ", hwif->name);
		if ((tmp = GET_ERR()) == 1)
			printk("success\n");
		else {
#if FANCY_STATUS_DUMPS
			printk("master: ");
			switch (tmp & 0x7f) {
				case 1: printk("passed");
					break;
				case 2: printk("formatter device error");
					break;
				case 3: printk("sector buffer error");
					break;
				case 4: printk("ECC circuitry error");
					break;
				case 5: printk("controlling MPU error");
					break;
				default:printk("error (0x%02x?)", tmp);
			}
			if (tmp & 0x80)
				printk("; slave: failed");
			printk("\n");
#else
			printk("failed\n");
#endif /* FANCY_STATUS_DUMPS */
		}
	}
	hwgroup->poll_timeout = 0;	/* done polling */
}

static void pre_reset (ide_drive_t *drive)
{
	if (!drive->keep_settings) {
		drive->unmask = 0;
		drive->io_32bit = 0;
		if (drive->using_dma)
			(void) HWIF(drive)->dmaproc(ide_dma_off, drive);
	}
	if (drive->driver != NULL)
		DRIVER(drive)->pre_reset(drive);
}

/*
 * do_reset1() attempts to recover a confused drive by resetting it.
 * Unfortunately, resetting a disk drive actually resets all devices on
 * the same interface, so it can really be thought of as resetting the
 * interface rather than resetting the drive.
 *
 * ATAPI devices have their own reset mechanism which allows them to be
 * individually reset without clobbering other devices on the same interface.
 *
 * Unfortunately, the IDE interface does not generate an interrupt to let
 * us know when the reset operation has finished, so we must poll for this.
 * Equally poor, though, is the fact that this may a very long time to complete,
 * (up to 30 seconds worstcase).  So, instead of busy-waiting here for it,
 * we set a timer to poll at 50ms intervals.
 */
static void do_reset1 (ide_drive_t *drive, int  do_not_try_atapi)
{
	unsigned int unit;
	unsigned long flags;
	ide_hwif_t *hwif = HWIF(drive);
	ide_hwgroup_t *hwgroup = HWGROUP(drive);

	__save_flags(flags);	/* local CPU only */
	__cli();		/* local CPU only */

	/* For an ATAPI device, first try an ATAPI SRST. */
	if (drive->media != ide_disk && !do_not_try_atapi) {
		pre_reset(drive);
		SELECT_DRIVE(hwif,drive);
		udelay (20);
		OUT_BYTE (WIN_SRST, IDE_COMMAND_REG);
		hwgroup->poll_timeout = jiffies + WAIT_WORSTCASE;
		ide_set_handler (drive, &atapi_reset_pollfunc, HZ/20);
		__restore_flags (flags);	/* local CPU only */
		return;
	}

	/*
	 * First, reset any device state data we were maintaining
	 * for any of the drives on this interface.
	 */
	for (unit = 0; unit < MAX_DRIVES; ++unit)
		pre_reset(&hwif->drives[unit]);

#if OK_TO_RESET_CONTROLLER
	/*
	 * Note that we also set nIEN while resetting the device,
	 * to mask unwanted interrupts from the interface during the reset.
	 * However, due to the design of PC hardware, this will cause an
	 * immediate interrupt due to the edge transition it produces.
	 * This single interrupt gives us a "fast poll" for drives that
	 * recover from reset very quickly, saving us the first 50ms wait time.
	 */
	OUT_BYTE(drive->ctl|6,IDE_CONTROL_REG);	/* set SRST and nIEN */
	udelay(10);			/* more than enough time */
	OUT_BYTE(drive->ctl|2,IDE_CONTROL_REG);	/* clear SRST, leave nIEN */
	udelay(10);			/* more than enough time */
	hwgroup->poll_timeout = jiffies + WAIT_WORSTCASE;
	ide_set_handler (drive, &reset_pollfunc, HZ/20);
#endif	/* OK_TO_RESET_CONTROLLER */

	__restore_flags (flags);	/* local CPU only */
}

/*
 * ide_do_reset() is the entry point to the drive/interface reset code.
 */
void ide_do_reset (ide_drive_t *drive)
{
	do_reset1 (drive, 0);
}

/*
 * Clean up after success/failure of an explicit drive cmd
 */
void ide_end_drive_cmd (ide_drive_t *drive, byte stat, byte err)
{
	unsigned long flags;
	struct request *rq = HWGROUP(drive)->rq;

	if (rq->cmd == IDE_DRIVE_CMD) {
		byte *args = (byte *) rq->buffer;
		rq->errors = !OK_STAT(stat,READY_STAT,BAD_STAT);
		if (args) {
			args[0] = stat;
			args[1] = err;
			args[2] = IN_BYTE(IDE_NSECTOR_REG);
		}
	}
	spin_lock_irqsave(&io_request_lock, flags);
	drive->queue = rq->next;
	blk_dev[MAJOR(rq->rq_dev)].current_request = NULL;
	HWGROUP(drive)->rq = NULL;
	rq->rq_status = RQ_INACTIVE;
	spin_unlock_irqrestore(&io_request_lock, flags);
	save_flags(flags);	/* all CPUs; overkill? */
	cli();			/* all CPUs; overkill? */
	if (rq->sem != NULL)
		up(rq->sem);	/* inform originator that rq has been serviced */
	restore_flags(flags);	/* all CPUs; overkill? */
}

/*
 * Error reporting, in human readable form (luxurious, but a memory hog).
 */
byte ide_dump_status (ide_drive_t *drive, const char *msg, byte stat)
{
	unsigned long flags;
	byte err = 0;

	__save_flags (flags);	/* local CPU only */
	ide__sti();		/* local CPU only */
	printk("%s: %s: status=0x%02x", drive->name, msg, stat);
#if FANCY_STATUS_DUMPS
	printk(" { ");
	if (stat & BUSY_STAT)
		printk("Busy ");
	else {
		if (stat & READY_STAT)	printk("DriveReady ");
		if (stat & WRERR_STAT)	printk("DeviceFault ");
		if (stat & SEEK_STAT)	printk("SeekComplete ");
		if (stat & DRQ_STAT)	printk("DataRequest ");
		if (stat & ECC_STAT)	printk("CorrectedError ");
		if (stat & INDEX_STAT)	printk("Index ");
		if (stat & ERR_STAT)	printk("Error ");
	}
	printk("}");
#endif	/* FANCY_STATUS_DUMPS */
	printk("\n");
	if ((stat & (BUSY_STAT|ERR_STAT)) == ERR_STAT) {
		err = GET_ERR();
		printk("%s: %s: error=0x%02x", drive->name, msg, err);
#if FANCY_STATUS_DUMPS
		if (drive->media == ide_disk) {
			printk(" { ");
			if (err & ABRT_ERR)	printk("DriveStatusError ");
			if (err & ICRC_ERR)	printk((err & ABRT_ERR) ? "BadCRC " : "BadSector ");
			if (err & ECC_ERR)	printk("UncorrectableError ");
			if (err & ID_ERR)	printk("SectorIdNotFound ");
			if (err & TRK0_ERR)	printk("TrackZeroNotFound ");
			if (err & MARK_ERR)	printk("AddrMarkNotFound ");
			printk("}");
			if ((err & (BBD_ERR | ABRT_ERR)) == BBD_ERR || (err & (ECC_ERR|ID_ERR|MARK_ERR))) {
				byte cur = IN_BYTE(IDE_SELECT_REG);
				if (cur & 0x40) {	/* using LBA? */
					printk(", LBAsect=%ld", (unsigned long)
					 ((cur&0xf)<<24)
					 |(IN_BYTE(IDE_HCYL_REG)<<16)
					 |(IN_BYTE(IDE_LCYL_REG)<<8)
					 | IN_BYTE(IDE_SECTOR_REG));
				} else {
					printk(", CHS=%d/%d/%d",
					 (IN_BYTE(IDE_HCYL_REG)<<8) +
					  IN_BYTE(IDE_LCYL_REG),
					  cur & 0xf,
					  IN_BYTE(IDE_SECTOR_REG));
				}
				if (HWGROUP(drive)->rq)
					printk(", sector=%ld", HWGROUP(drive)->rq->sector);
			}
		}
#endif	/* FANCY_STATUS_DUMPS */
		printk("\n");
	}
	__restore_flags (flags);	/* local CPU only */
	return err;
}

/*
 * try_to_flush_leftover_data() is invoked in response to a drive
 * unexpectedly having its DRQ_STAT bit set.  As an alternative to
 * resetting the drive, this routine tries to clear the condition
 * by read a sector's worth of data from the drive.  Of course,
 * this may not help if the drive is *waiting* for data from *us*.
 */
static void try_to_flush_leftover_data (ide_drive_t *drive)
{
	int i = (drive->mult_count ? drive->mult_count : 1) * SECTOR_WORDS;

	if (drive->media != ide_disk)
		return;
	while (i > 0) {
		unsigned long buffer[16];
		unsigned int wcount = (i > 16) ? 16 : i;
		i -= wcount;
		ide_input_data (drive, buffer, wcount);
	}
}

/*
 * ide_error() takes action based on the error returned by the drive.
 */
void ide_error (ide_drive_t *drive, const char *msg, byte stat)
{
	struct request *rq;
	byte err;

	err = ide_dump_status(drive, msg, stat);
	if (drive == NULL || (rq = HWGROUP(drive)->rq) == NULL)
		return;
	/* retry only "normal" I/O: */
	if (rq->cmd == IDE_DRIVE_CMD) {
		rq->errors = 1;
		ide_end_drive_cmd(drive, stat, err);
		return;
	}
	if (stat & BUSY_STAT) {		/* other bits are useless when BUSY */
		rq->errors |= ERROR_RESET;
	} else {
		if (drive->media == ide_disk && (stat & ERR_STAT)) {
			/* err has different meaning on cdrom and tape */
			if (err == ABRT_ERR) {
				if (drive->select.b.lba && IN_BYTE(IDE_COMMAND_REG) == WIN_SPECIFY)
					return;	/* some newer drives don't support WIN_SPECIFY */
			} else if ((err & (ABRT_ERR | ICRC_ERR)) == (ABRT_ERR | ICRC_ERR))
				; /* UDMA crc error -- just retry the operation */
			else if (err & (BBD_ERR | ECC_ERR))	/* retries won't help these */
				rq->errors = ERROR_MAX;
			else if (err & TRK0_ERR)	/* help it find track zero */
				rq->errors |= ERROR_RECAL;
		}
		if ((stat & DRQ_STAT) && rq->cmd != WRITE)
			try_to_flush_leftover_data(drive);
	}
	if (GET_STAT() & (BUSY_STAT|DRQ_STAT))
		rq->errors |= ERROR_RESET;	/* Mmmm.. timing problem */

	if (rq->errors >= ERROR_MAX) {
		if (drive->driver != NULL)
			DRIVER(drive)->end_request(0, HWGROUP(drive));
		else
	 		ide_end_request(0, HWGROUP(drive));
	} else {
		if ((rq->errors & ERROR_RESET) == ERROR_RESET) {
			++rq->errors;
			ide_do_reset(drive);
			return;
		} else if ((rq->errors & ERROR_RECAL) == ERROR_RECAL)
			drive->special.b.recalibrate = 1;
		++rq->errors;
	}
}

/*
 * Issue a simple drive command
 * The drive must be selected beforehand.
 */
void ide_cmd(ide_drive_t *drive, byte cmd, byte nsect, ide_handler_t *handler)
{
	ide_set_handler (drive, handler, WAIT_CMD);
	OUT_BYTE(drive->ctl,IDE_CONTROL_REG);	/* clear nIEN */
	OUT_BYTE(nsect,IDE_NSECTOR_REG);
	OUT_BYTE(cmd,IDE_COMMAND_REG);
}

/*
 * drive_cmd_intr() is invoked on completion of a special DRIVE_CMD.
 */
static void drive_cmd_intr (ide_drive_t *drive)
{
	struct request *rq = HWGROUP(drive)->rq;
	byte *args = (byte *) rq->buffer;
	byte stat = GET_STAT();
	int retries = 10;

	ide__sti();	/* local CPU only */
	if ((stat & DRQ_STAT) && args && args[3]) {
		byte io_32bit = drive->io_32bit;
		drive->io_32bit = 0;
		ide_input_data(drive, &args[4], args[3] * SECTOR_WORDS);
		drive->io_32bit = io_32bit;
		while (((stat = GET_STAT()) & BUSY_STAT) && retries--)
			udelay(100);
	}

	if (OK_STAT(stat, READY_STAT, BAD_STAT))
		ide_end_drive_cmd (drive, stat, GET_ERR());
	else
		ide_error(drive, "drive_cmd", stat); /* calls ide_end_drive_cmd */
}

/*
 * do_special() is used to issue WIN_SPECIFY, WIN_RESTORE, and WIN_SETMULT
 * commands to a drive.  It used to do much more, but has been scaled back.
 */
static inline void do_special (ide_drive_t *drive)
{
	special_t *s = &drive->special;

#ifdef DEBUG
	printk("%s: do_special: 0x%02x\n", drive->name, s->all);
#endif
	if (s->b.set_tune) {
		ide_tuneproc_t *tuneproc = HWIF(drive)->tuneproc;
		s->b.set_tune = 0;
		if (tuneproc != NULL)
			tuneproc(drive, drive->tune_req);
	} else if (drive->driver != NULL) {
		DRIVER(drive)->special(drive);
	} else if (s->all) {
		printk("%s: bad special flag: 0x%02x\n", drive->name, s->all);
		s->all = 0;
	}
}

/*
 * This routine busy-waits for the drive status to be not "busy".
 * It then checks the status for all of the "good" bits and none
 * of the "bad" bits, and if all is okay it returns 0.  All other
 * cases return 1 after invoking ide_error() -- caller should just return.
 *
 * This routine should get fixed to not hog the cpu during extra long waits..
 * That could be done by busy-waiting for the first jiffy or two, and then
 * setting a timer to wake up at half second intervals thereafter,
 * until timeout is achieved, before timing out.
 */
int ide_wait_stat (ide_drive_t *drive, byte good, byte bad, unsigned long timeout)
{
	byte stat;
	unsigned long flags;

	udelay(1);	/* spec allows drive 400ns to assert "BUSY" */
	if ((stat = GET_STAT()) & BUSY_STAT) {
		__save_flags(flags);	/* local CPU only */
		ide__sti();		/* local CPU only */
		timeout += jiffies;
		while ((stat = GET_STAT()) & BUSY_STAT) {
			if (0 < (signed long)(jiffies - timeout)) {
				__restore_flags(flags);	/* local CPU only */
				ide_error(drive, "status timeout", stat);
				return 1;
			}
		}
		__restore_flags(flags);	/* local CPU only */
	}
	udelay(1);	/* allow status to settle, then read it again */
	if (OK_STAT((stat = GET_STAT()), good, bad))
		return 0;
	ide_error(drive, "status error", stat);
	return 1;
}

/*
 * execute_drive_cmd() issues a special drive command,
 * usually initiated by ioctl() from the external hdparm program.
 */
static void execute_drive_cmd (ide_drive_t *drive, struct request *rq)
{
	byte *args = rq->buffer;
	if (args) {
#ifdef DEBUG
		printk("%s: DRIVE_CMD cmd=0x%02x sc=0x%02x fr=0x%02x xx=0x%02x\n",
		 drive->name, args[0], args[1], args[2], args[3]);
#endif
		if (args[0] == WIN_SMART) {
			OUT_BYTE(0x4f, IDE_LCYL_REG);
			OUT_BYTE(0xc2, IDE_HCYL_REG);
		}
		OUT_BYTE(args[2],IDE_FEATURE_REG);
		ide_cmd(drive, args[0], args[1], &drive_cmd_intr);
		return;
	} else {
		/*
		 * NULL is actually a valid way of waiting for
		 * all current requests to be flushed from the queue.
		 */
#ifdef DEBUG
		printk("%s: DRIVE_CMD (null)\n", drive->name);
#endif
		ide_end_drive_cmd(drive, GET_STAT(), GET_ERR());
		return;
	}
}

/*
 * start_request() initiates handling of a new I/O request
 */
static inline void start_request (ide_drive_t *drive)
{
	unsigned long block, blockend;
	struct request *rq = drive->queue;
	unsigned int minor = MINOR(rq->rq_dev), unit = minor >> PARTN_BITS;
	ide_hwif_t *hwif = HWIF(drive);

	ide__sti();	/* local CPU only */
#ifdef DEBUG
	printk("%s: start_request: current=0x%08lx\n", hwif->name, (unsigned long) rq);
#endif
	if (unit >= MAX_DRIVES) {
		printk("%s: bad device number: %s\n", hwif->name, kdevname(rq->rq_dev));
		goto kill_rq;
	}
#ifdef DEBUG
	if (rq->bh && !buffer_locked(rq->bh)) {
		printk("%s: block not locked\n", drive->name);
		goto kill_rq;
	}
#endif
	block    = rq->sector;
	blockend = block + rq->nr_sectors;
	if ((blockend < block) || (blockend > drive->part[minor&PARTN_MASK].nr_sects)) {
		printk("%s%c: bad access: block=%ld, count=%ld\n", drive->name,
		 (minor&PARTN_MASK)?'0'+(minor&PARTN_MASK):' ', block, rq->nr_sectors);
		goto kill_rq;
	}
	block += drive->part[minor&PARTN_MASK].start_sect + drive->sect0;
#if FAKE_FDISK_FOR_EZDRIVE
	if (block == 0 && drive->remap_0_to_1)
		block = 1;  /* redirect MBR access to EZ-Drive partn table */
#endif /* FAKE_FDISK_FOR_EZDRIVE */
#if (DISK_RECOVERY_TIME > 0)
	while ((read_timer() - hwif->last_time) < DISK_RECOVERY_TIME);
#endif
	SELECT_DRIVE(hwif, drive);
	if (ide_wait_stat(drive, drive->ready_stat, BUSY_STAT|DRQ_STAT, WAIT_READY)) {
		printk("%s: drive not ready for command\n", drive->name);
		return;
	}
	if (!drive->special.all) {
		if (rq->cmd == IDE_DRIVE_CMD) {
			execute_drive_cmd(drive, rq);
			return;
		}
		if (drive->driver != NULL) {
			DRIVER(drive)->do_request(drive, rq, block);
			return;
		}
		printk("%s: media type %d not supported\n", drive->name, drive->media);
		goto kill_rq;
	}
	do_special(drive);
	return;
kill_rq:
	if (drive->driver != NULL)
		DRIVER(drive)->end_request(0, HWGROUP(drive));
	else
		ide_end_request(0, HWGROUP(drive));
}

/*
 * ide_stall_queue() can be used by a drive to give excess bandwidth back
 * to the hwgroup by sleeping for timeout jiffies.
 */
void ide_stall_queue (ide_drive_t *drive, unsigned long timeout)
{
	if (timeout > WAIT_WORSTCASE)
		timeout = WAIT_WORSTCASE;
	drive->sleep = timeout + jiffies;
}

#define WAKEUP(drive)	((drive)->service_start + 2 * (drive)->service_time)

/*
 * choose_drive() selects the next drive which will be serviced.
 */
static inline ide_drive_t *choose_drive (ide_hwgroup_t *hwgroup)
{
	ide_drive_t *drive, *best;

repeat:	
	best = NULL;
	drive = hwgroup->drive;
	do {
		if (drive->queue && (!drive->sleep || 0 <= (signed long)(jiffies - drive->sleep))) {
			if (!best
			 || (drive->sleep && (!best->sleep || 0 < (signed long)(best->sleep - drive->sleep)))
			 || (!best->sleep && 0 < (signed long)(WAKEUP(best) - WAKEUP(drive))))
			{
				struct blk_dev_struct *bdev = &blk_dev[HWIF(drive)->major];
				if (bdev->current_request != &bdev->plug)
					best = drive;
			}
		}
	} while ((drive = drive->next) != hwgroup->drive);
	if (best && best->nice1 && !best->sleep && best != hwgroup->drive && best->service_time > WAIT_MIN_SLEEP) {
		long t = (signed long)(WAKEUP(best) - jiffies);
		if (t >= WAIT_MIN_SLEEP) {
			/*
			 * We *may* have some time to spare, but first let's see if
			 * someone can potentially benefit from our nice mood today..
			 */
			drive = best->next;
			do {
				if (!drive->sleep
				 && 0 < (signed long)(WAKEUP(drive) - (jiffies - best->service_time))
				 && 0 < (signed long)((jiffies + t) - WAKEUP(drive)))
				{
					ide_stall_queue(best, IDE_MIN(t, 10 * WAIT_MIN_SLEEP));
					goto repeat;
				}
			} while ((drive = drive->next) != best);
		}
	}
	return best;
}

/*
 * Caller must have already acquired spinlock using *spinflags 
 */
static void ide_do_request (ide_hwgroup_t *hwgroup, unsigned long *hwgroup_flags, int masked_irq)
{
	struct blk_dev_struct *bdev;
	ide_drive_t	*drive;
	ide_hwif_t	*hwif;
	unsigned long	io_flags;

	hwgroup->busy = 1;
	while (hwgroup->handler == NULL) {
		spin_lock_irqsave(&io_request_lock, io_flags);
		drive = choose_drive(hwgroup);
		if (drive == NULL) {
			unsigned long sleep = 0;

			hwgroup->rq = NULL;
			drive = hwgroup->drive;
			do {
				bdev = &blk_dev[HWIF(drive)->major];
				if (bdev->current_request != &bdev->plug)	/* FIXME: this will do for now */
					bdev->current_request = NULL;		/* (broken since patch-2.1.15) */
				if (drive->sleep && (!sleep || 0 < (signed long)(sleep - drive->sleep)))
					sleep = drive->sleep;
			} while ((drive = drive->next) != hwgroup->drive);
			spin_unlock_irqrestore(&io_request_lock, io_flags);
			if (sleep) {
				if (0 < (signed long)(jiffies + WAIT_MIN_SLEEP - sleep)) 
					sleep = jiffies + WAIT_MIN_SLEEP;
#if 1
				if (hwgroup->timer.next || hwgroup->timer.prev)
					printk("ide_set_handler: timer already active\n");
#endif
				mod_timer(&hwgroup->timer, sleep);
			} else {
				/* Ugly, but how can we sleep for the lock otherwise? perhaps from tq_scheduler? */
				ide_release_lock(&ide_lock);	/* for atari only */
			}
			hwgroup->busy = 0;
			return;
		}
		hwif = HWIF(drive);
		if (hwgroup->hwif->sharing_irq && hwif != hwgroup->hwif) /* set nIEN for previous hwif */
			OUT_BYTE(hwgroup->drive->ctl|2, hwgroup->hwif->io_ports[IDE_CONTROL_OFFSET]);
		hwgroup->hwif = hwif;
		hwgroup->drive = drive;
		drive->sleep = 0;
		drive->service_start = jiffies;

		bdev = &blk_dev[hwif->major];
		if (bdev->current_request == &bdev->plug)	/* FIXME: paranoia */
			printk("%s: Huh? nuking plugged queue\n", drive->name);
		bdev->current_request = hwgroup->rq = drive->queue;
		spin_unlock_irqrestore(&io_request_lock, io_flags);

		if (hwif->irq != masked_irq)
			disable_irq(hwif->irq);
		spin_unlock_irqrestore(&hwgroup->spinlock, *hwgroup_flags);
		start_request(drive);
		spin_lock_irqsave(&hwgroup->spinlock, *hwgroup_flags);
		if (hwif->irq != masked_irq)
			enable_irq(hwif->irq);
	}
}

/*
 * ide_get_queue() returns the queue which corresponds to a given device.
 */
struct request **ide_get_queue (kdev_t dev)
{
	ide_hwif_t *hwif = (ide_hwif_t *)blk_dev[MAJOR(dev)].data;

	return &hwif->drives[DEVICE_NR(dev) & 1].queue;
}

/*
 * do_hwgroup_request() invokes ide_do_request() after claiming hwgroup->busy.
 */
static void do_hwgroup_request (ide_hwgroup_t *hwgroup)
{
	unsigned long flags;

	spin_lock_irqsave(&hwgroup->spinlock, flags);
	if (hwgroup->busy) {
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		return;
	}
	del_timer(&hwgroup->timer);
	ide_get_lock(&ide_lock, ide_intr, hwgroup);	/* for atari only */
	ide_do_request(hwgroup, &flags, 0);
	spin_unlock_irqrestore(&hwgroup->spinlock, flags);
}

/*
 * ll_rw_blk.c invokes our do_idex_request() function
 * with the io_request_spinlock already grabbed.
 * Since we need to do our own spinlock's internally,
 * on paths that don't necessarily originate through the
 * do_idex_request() path, we have to undo the spinlock on entry,
 * and restore it again on exit.
 * Fortunately, this is mostly a nop for non-SMP kernels.
 */
static inline void unlock_do_hwgroup_request (ide_hwgroup_t *hwgroup)
{
	spin_unlock(&io_request_lock);
	do_hwgroup_request (hwgroup);
	spin_lock_irq(&io_request_lock);
}

void do_ide0_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[0].hwgroup);
}

#if MAX_HWIFS > 1
void do_ide1_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[1].hwgroup);
}
#endif /* MAX_HWIFS > 1 */

#if MAX_HWIFS > 2
void do_ide2_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[2].hwgroup);
}
#endif /* MAX_HWIFS > 2 */

#if MAX_HWIFS > 3
void do_ide3_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[3].hwgroup);
}
#endif /* MAX_HWIFS > 3 */

#if MAX_HWIFS > 4
void do_ide4_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[4].hwgroup);
}
#endif /* MAX_HWIFS > 4 */

#if MAX_HWIFS > 5
void do_ide5_request (void)
{
	unlock_do_hwgroup_request (ide_hwifs[5].hwgroup);
}
#endif /* MAX_HWIFS > 5 */

static void start_next_request (ide_hwgroup_t *hwgroup, int masked_irq)
{
	unsigned long	flags;
	ide_drive_t	*drive;

	spin_lock_irqsave(&hwgroup->spinlock, flags);
	if (hwgroup->handler != NULL) {
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		return;
	}
	drive = hwgroup->drive;
	set_recovery_timer(HWIF(drive));
	drive->service_time = jiffies - drive->service_start;
	ide_do_request(hwgroup, &flags, masked_irq);
	spin_unlock_irqrestore(&hwgroup->spinlock, flags);
}

void ide_timer_expiry (unsigned long data)
{
	ide_hwgroup_t *hwgroup = (ide_hwgroup_t *) data;
	ide_drive_t   *drive;
	ide_handler_t *handler;
	unsigned long flags;

	spin_lock_irqsave(&hwgroup->spinlock, flags);
	drive = hwgroup->drive;
	if ((handler = hwgroup->handler) == NULL) {
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		do_hwgroup_request(hwgroup);
		return;
	}
	hwgroup->busy = 1;	/* should already be "1" */
	hwgroup->handler = NULL;
	del_timer(&hwgroup->timer);	/* Is this needed?? */
	if (hwgroup->poll_timeout != 0) {	/* polling in progress? */
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		handler(drive);
	} else if (drive_is_ready(drive)) {
		printk("%s: lost interrupt\n", drive->name);
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		handler(drive);
	} else {
		if (drive->waiting_for_dma) {
			(void) hwgroup->hwif->dmaproc(ide_dma_end, drive);
			printk("%s: timeout waiting for DMA\n", drive->name);
	/*
	 *  need something here for HX PIIX3 UDMA and HPT343.......AMH
	 *  irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
	 */
		}
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		ide_error(drive, "irq timeout", GET_STAT());
	}
	start_next_request(hwgroup, 0);
}

/*
 * There's nothing really useful we can do with an unexpected interrupt,
 * other than reading the status register (to clear it), and logging it.
 * There should be no way that an irq can happen before we're ready for it,
 * so we needn't worry much about losing an "important" interrupt here.
 *
 * On laptops (and "green" PCs), an unexpected interrupt occurs whenever the
 * drive enters "idle", "standby", or "sleep" mode, so if the status looks
 * "good", we just ignore the interrupt completely.
 *
 * This routine assumes __cli() is in effect when called.
 *
 * If an unexpected interrupt happens on irq15 while we are handling irq14
 * and if the two interfaces are "serialized" (CMD640), then it looks like
 * we could screw up by interfering with a new request being set up for irq15.
 *
 * In reality, this is a non-issue.  The new command is not sent unless the
 * drive is ready to accept one, in which case we know the drive is not
 * trying to interrupt us.  And ide_set_handler() is always invoked before
 * completing the issuance of any new drive command, so we will not be
 * accidently invoked as a result of any valid command completion interrupt.
 *
 */
static void unexpected_intr (int irq, ide_hwgroup_t *hwgroup)
{
	byte stat;
	ide_hwif_t *hwif = hwgroup->hwif;

	/*
	 * handle the unexpected interrupt
	 */
	do {
		if (hwif->irq == irq) {
			stat = IN_BYTE(hwif->io_ports[IDE_STATUS_OFFSET]);
			if (!OK_STAT(stat, READY_STAT, BAD_STAT)) {
				/* Try to not flood the console with msgs */
				static unsigned long last_msgtime = 0, count = 0;
				++count;
				if (0 < (signed long)(jiffies - (last_msgtime + HZ))) {
					last_msgtime = jiffies;
					printk("%s%s: unexpected interrupt, status=0x%02x, count=%ld\n",
					 hwif->name, (hwif->next == hwgroup->hwif) ? "" : "(?)", stat, count);
				}
			}
		}
	} while ((hwif = hwif->next) != hwgroup->hwif);
}
/*
 * entry point for all interrupts, caller does __cli() for us
 */
void ide_intr (int irq, void *dev_id, struct pt_regs *regs)
{
	unsigned long flags;
	ide_hwgroup_t *hwgroup = (ide_hwgroup_t *)dev_id;
	ide_hwif_t *hwif;
	ide_drive_t *drive;
	ide_handler_t *handler;

	__cli();	/* local CPU only */
	spin_lock_irqsave(&hwgroup->spinlock, flags);
	hwif = hwgroup->hwif;
	if ((handler = hwgroup->handler) == NULL || hwgroup->poll_timeout != 0) {
		/*
		 * Not expecting an interrupt from this drive.
		 * That means this could be:
		 *	(1) an interrupt from another PCI device
		 *	sharing the same PCI INT# as us.
		 * or	(2) a drive just entered sleep or standby mode,
		 *	and is interrupting to let us know.
		 * or	(3) a spurious interrupt of unknown origin.
		 *
		 * For PCI, we cannot tell the difference,
		 * so in that case we just ignore it and hope it goes away.
		 */
#ifdef CONFIG_BLK_DEV_IDEPCI
		if (IDE_PCI_DEVID_EQ(hwif->pci_devid, IDE_PCI_DEVID_NULL))
#endif	/* CONFIG_BLK_DEV_IDEPCI */
		{
			/*
			 * Probably not a shared PCI interrupt,
			 * so we can safely try to do something about it:
			 */
			(void)ide_ack_intr(hwif->io_ports[IDE_STATUS_OFFSET], hwif->io_ports[IDE_IRQ_OFFSET]);
			unexpected_intr(irq, hwgroup);
		}
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		return;
	}
	drive = hwgroup->drive;
	if (!drive || !drive_is_ready(drive)) {
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		return;
	}
	hwgroup->handler = NULL;
	(void)ide_ack_intr(hwif->io_ports[IDE_STATUS_OFFSET], hwif->io_ports[IDE_IRQ_OFFSET]);
	del_timer(&(hwgroup->timer));
	spin_unlock_irqrestore(&hwgroup->spinlock, flags);
	if (drive->unmask)
		ide__sti();	/* local CPU only */
	handler(drive);		/* service this interrupt, may set handler for next interrupt */
	/*
	 * Note that handler() may have set things up for another
	 * interrupt to occur soon, but it cannot happen until
	 * we exit from this routine, because it will be the
	 * same irq as is currently being serviced here,
	 * and Linux won't allow another (on any CPU) until we return.
	 */
	start_next_request(hwgroup, hwif->irq);
}

/*
 * get_info_ptr() returns the (ide_drive_t *) for a given device number.
 * It returns NULL if the given device number does not match any present drives.
 */
static ide_drive_t *get_info_ptr (kdev_t i_rdev)
{
	int		major = MAJOR(i_rdev);
	unsigned int	h;

	for (h = 0; h < MAX_HWIFS; ++h) {
		ide_hwif_t  *hwif = &ide_hwifs[h];
		if (hwif->present && major == hwif->major) {
			unsigned unit = DEVICE_NR(i_rdev);
			if (unit < MAX_DRIVES) {
				ide_drive_t *drive = &hwif->drives[unit];
				if (drive->present)
					return drive;
			}
			break;
		}
	}
	return NULL;
}

/*
 * This function is intended to be used prior to invoking ide_do_drive_cmd().
 */
void ide_init_drive_cmd (struct request *rq)
{
	rq->buffer = NULL;
	rq->cmd = IDE_DRIVE_CMD;
	rq->sector = 0;
	rq->nr_sectors = 0;
	rq->current_nr_sectors = 0;
	rq->sem = NULL;
	rq->bh = NULL;
	rq->bhtail = NULL;
	rq->next = NULL;
}

/*
 * This function issues a special IDE device request
 * onto the request queue.
 *
 * If action is ide_wait, then the rq is queued at the end of the
 * request queue, and the function sleeps until it has been processed.
 * This is for use when invoked from an ioctl handler.
 *
 * If action is ide_preempt, then the rq is queued at the head of
 * the request queue, displacing the currently-being-processed
 * request and this function returns immediately without waiting
 * for the new rq to be completed.  This is VERY DANGEROUS, and is
 * intended for careful use by the ATAPI tape/cdrom driver code.
 *
 * If action is ide_next, then the rq is queued immediately after
 * the currently-being-processed-request (if any), and the function
 * returns without waiting for the new rq to be completed.  As above,
 * This is VERY DANGEROUS, and is intended for careful use by the
 * ATAPI tape/cdrom driver code.
 *
 * If action is ide_end, then the rq is queued at the end of the
 * request queue, and the function returns immediately without waiting
 * for the new rq to be completed. This is again intended for careful
 * use by the ATAPI tape/cdrom driver code.
 */
int ide_do_drive_cmd (ide_drive_t *drive, struct request *rq, ide_action_t action)
{
	unsigned long flags;
	ide_hwgroup_t *hwgroup = HWGROUP(drive);
	unsigned int major = HWIF(drive)->major;
	struct request *cur_rq;
	struct semaphore sem = MUTEX_LOCKED;

	if (IS_PDC4030_DRIVE && rq->buffer != NULL)
		return -ENOSYS;  /* special drive cmds not supported */
	rq->errors = 0;
	rq->rq_status = RQ_ACTIVE;
	rq->rq_dev = MKDEV(major,(drive->select.b.unit)<<PARTN_BITS);
	if (action == ide_wait)
		rq->sem = &sem;

	spin_lock_irqsave(&io_request_lock, flags);
	cur_rq = drive->queue;
	if (cur_rq == NULL || action == ide_preempt) {
		rq->next = cur_rq;
		drive->queue = rq;
		if (action == ide_preempt)
			hwgroup->rq = NULL;
	} else {
		if (action == ide_wait || action == ide_end) {
			while (cur_rq->next != NULL)	/* find end of list */
				cur_rq = cur_rq->next;
		}
		rq->next = cur_rq->next;
		cur_rq->next = rq;
	}
	spin_unlock_irqrestore(&io_request_lock, flags);
	do_hwgroup_request(hwgroup);
	save_flags(flags);	/* all CPUs; overkill? */
	cli();			/* all CPUs; overkill? */
	if (action == ide_wait && rq->rq_status != RQ_INACTIVE)
		down(&sem);	/* wait for it to be serviced */
	restore_flags(flags);	/* all CPUs; overkill? */
	return rq->errors ? -EIO : 0;	/* return -EIO if errors */
}

/*
 * This routine is called to flush all partitions and partition tables
 * for a changed disk, and then re-read the new partition table.
 * If we are revalidating a disk because of a media change, then we
 * enter with usage == 0.  If we are using an ioctl, we automatically have
 * usage == 1 (we need an open channel to use an ioctl :-), so this
 * is our limit.
 */
int ide_revalidate_disk(kdev_t i_rdev)
{
	ide_drive_t *drive;
	ide_hwgroup_t *hwgroup;
	unsigned int p, major, minor;
	long flags;

	if ((drive = get_info_ptr(i_rdev)) == NULL)
		return -ENODEV;
	major = MAJOR(i_rdev);
	minor = drive->select.b.unit << PARTN_BITS;
	hwgroup = HWGROUP(drive);
	spin_lock_irqsave(&hwgroup->spinlock, flags);
	if (drive->busy || (drive->usage > 1)) {
		spin_unlock_irqrestore(&hwgroup->spinlock, flags);
		return -EBUSY;
	};
	drive->busy = 1;
	MOD_INC_USE_COUNT;
	spin_unlock_irqrestore(&hwgroup->spinlock, flags);

	for (p = 0; p < (1<<PARTN_BITS); ++p) {
		if (drive->part[p].nr_sects > 0) {
			kdev_t devp = MKDEV(major, minor+p);
			struct super_block * sb = get_super(devp);
			fsync_dev          (devp);
			if (sb)
				invalidate_inodes(sb);
			invalidate_buffers (devp);
			set_blocksize(devp, 1024);
		}
		drive->part[p].start_sect = 0;
		drive->part[p].nr_sects   = 0;
	};

	drive->part[0].nr_sects = current_capacity(drive);
	if ((drive->media != ide_disk && drive->media != ide_floppy) ||
	     drive->driver == NULL || !drive->part[0].nr_sects)
		drive->part[0].start_sect = -1;
	resetup_one_dev(HWIF(drive)->gd, drive->select.b.unit);

	drive->busy = 0;
	wake_up(&drive->wqueue);
	MOD_DEC_USE_COUNT;
	return 0;
}

static void revalidate_drives (void)
{
	ide_hwif_t *hwif;
	ide_drive_t *drive;
	int index, unit;

	for (index = 0; index < MAX_HWIFS; ++index) {
		hwif = &ide_hwifs[index];
		for (unit = 0; unit < MAX_DRIVES; ++unit) {
			drive = &ide_hwifs[index].drives[unit];
			if (drive->revalidate) {
				drive->revalidate = 0;
				if (!initializing)
					(void) ide_revalidate_disk(MKDEV(hwif->major, unit<<PARTN_BITS));
			}
		}
	}
}

static void ide_init_module (int type)
{
	int found = 0;
	ide_module_t *module = ide_modules;
	
	while (module) {
		if (module->type == type) {
			found = 1;
			(void) module->init();
		}
		module = module->next;
	}
	revalidate_drives();
#ifdef CONFIG_KMOD
	if (!found && type == IDE_PROBE_MODULE)
		(void) request_module("ide-probe");
#endif /* CONFIG_KMOD */
}

static int ide_open(struct inode * inode, struct file * filp)
{
	ide_drive_t *drive;
	int rc;

	if ((drive = get_info_ptr(inode->i_rdev)) == NULL)
		return -ENXIO;
	MOD_INC_USE_COUNT;
	if (drive->driver == NULL)
		ide_init_module(IDE_DRIVER_MODULE);
#ifdef CONFIG_KMOD
	if (drive->driver == NULL) {
		if (drive->media == ide_disk)
			(void) request_module("ide-disk");
		if (drive->media == ide_cdrom)
			(void) request_module("ide-cd");
		if (drive->media == ide_tape)
			(void) request_module("ide-tape");
		if (drive->media == ide_floppy)
			(void) request_module("ide-floppy");
	}
#endif /* CONFIG_KMOD */
	while (drive->busy)
		sleep_on(&drive->wqueue);
	drive->usage++;
	if (drive->driver != NULL) {
		if ((rc = DRIVER(drive)->open(inode, filp, drive)))
			MOD_DEC_USE_COUNT;
		return rc;
	}
	printk ("%s: driver not present\n", drive->name);
	drive->usage--;
	MOD_DEC_USE_COUNT;
	return -ENXIO;
}

/*
 * Releasing a block device means we sync() it, so that it can safely
 * be forgotten about...
 */
static int ide_release(struct inode * inode, struct file * file)
{
	ide_drive_t *drive;

	if ((drive = get_info_ptr(inode->i_rdev)) != NULL) {
		fsync_dev(inode->i_rdev);
		drive->usage--;
		if (drive->driver != NULL)
			DRIVER(drive)->release(inode, file, drive);
		MOD_DEC_USE_COUNT;
	}
	return 0;
}

int ide_replace_subdriver(ide_drive_t *drive, const char *driver)
{
	if (!drive->present || drive->busy || drive->usage)
		goto abort;
	if (drive->driver != NULL && DRIVER(drive)->cleanup(drive))
		goto abort;
	strncpy(drive->driver_req, driver, 9);
	ide_init_module(IDE_DRIVER_MODULE);
	drive->driver_req[0] = 0;
	ide_init_module(IDE_DRIVER_MODULE);
	if (DRIVER(drive) && !strcmp(DRIVER(drive)->name, driver))
		return 0;
abort:
	return 1;
}

void ide_unregister (unsigned int index)
{
	struct gendisk *gd, **gdp;
	ide_drive_t *drive, *d;
	ide_hwif_t *hwif, *g;
	ide_hwgroup_t *hwgroup;
	int irq_count = 0, unit, i;
	unsigned long flags;

	if (index >= MAX_HWIFS)
		return;
	save_flags(flags);	/* all CPUs */
	cli();			/* all CPUs */
	hwif = &ide_hwifs[index];
	if (!hwif->present)
		goto abort;
	for (unit = 0; unit < MAX_DRIVES; ++unit) {
		drive = &hwif->drives[unit];
		if (!drive->present)
			continue;
		if (drive->busy || drive->usage)
			goto abort;
		if (drive->driver != NULL && DRIVER(drive)->cleanup(drive))
			goto abort;
	}
	hwif->present = 0;
	hwgroup = hwif->hwgroup;

	/*
	 * free the irq if we were the only hwif using it
	 */
	g = hwgroup->hwif;
	do {
		if (g->irq == hwif->irq)
			++irq_count;
		g = g->next;
	} while (g != hwgroup->hwif);
	if (irq_count == 1)
		free_irq(hwif->irq, hwgroup);

	/*
	 * Note that we only release the standard ports,
	 * and do not even try to handle any extra ports
	 * allocated for weird IDE interface chipsets.
	 */
	ide_release_region(hwif->io_ports[IDE_DATA_OFFSET], 8);
	ide_release_region(hwif->io_ports[IDE_CONTROL_OFFSET], 1);

	/*
	 * Remove us from the hwgroup, and free
	 * the hwgroup if we were the only member
	 */
	d = hwgroup->drive;
	for (i = 0; i < MAX_DRIVES; ++i) {
		drive = &hwif->drives[i];
		if (!drive->present)
			continue;
		while (hwgroup->drive->next != drive)
			hwgroup->drive = hwgroup->drive->next;
		hwgroup->drive->next = drive->next;
		if (hwgroup->drive == drive)
			hwgroup->drive = NULL;
		if (drive->id != NULL) {
			kfree(drive->id);
			drive->id = NULL;
		}
		drive->present = 0;
	}
	if (d->present)
		hwgroup->drive = d;
	while (hwgroup->hwif->next != hwif)
		hwgroup->hwif = hwgroup->hwif->next;
	hwgroup->hwif->next = hwif->next;
	if (hwgroup->hwif == hwif)
		kfree(hwgroup);
	else
		hwgroup->hwif = HWIF(hwgroup->drive);

#ifdef CONFIG_BLK_DEV_IDEDMA
	if (hwif->dma_base)
		(void) ide_release_dma(hwif);
#endif /* CONFIG_BLK_DEV_IDEDMA */

	/*
	 * Remove us from the kernel's knowledge
	 */
	unregister_blkdev(hwif->major, hwif->name);
	kfree(blksize_size[hwif->major]);
	kfree(max_sectors[hwif->major]);
	kfree(max_readahead[hwif->major]);
	blk_dev[hwif->major].request_fn = NULL;
	blk_dev[hwif->major].data = NULL;
	blk_dev[hwif->major].queue = NULL;
	blksize_size[hwif->major] = NULL;
	for (gdp = &gendisk_head; *gdp; gdp = &((*gdp)->next))
		if (*gdp == hwif->gd)
			break;
	if (*gdp == NULL)
		printk("gd not in disk chain!\n");
	else {
		gd = *gdp; *gdp = gd->next;
		kfree(gd->sizes);
		kfree(gd->part);
		kfree(gd);
	}
	init_hwif_data (index);	/* restore hwif data to pristine status */
abort:
	restore_flags(flags);	/* all CPUs */
}

int ide_register (int arg1, int arg2, int irq)
{
	int index, retry = 1;
	ide_hwif_t *hwif;
	ide_ioreg_t data_port = (ide_ioreg_t) arg1, ctl_port = (ide_ioreg_t) arg2;

	do {
		for (index = 0; index < MAX_HWIFS; ++index) {
			hwif = &ide_hwifs[index];
			if (hwif->io_ports[IDE_DATA_OFFSET] == data_port)
				goto found;
		}
		for (index = 0; index < MAX_HWIFS; ++index) {
			hwif = &ide_hwifs[index];
			if (!hwif->present)
				goto found;
		}
		for (index = 0; index < MAX_HWIFS; index++)
			ide_unregister(index);
	} while (retry--);
	return -1;
found:
	if (hwif->present)
		ide_unregister(index);
	if (hwif->present)
		return -1;
	ide_init_hwif_ports(hwif->io_ports, data_port, &hwif->irq);
	if (ctl_port)
		hwif->io_ports[IDE_CONTROL_OFFSET] = ctl_port;
	hwif->irq = irq;
	hwif->noprobe = 0;
	ide_init_module(IDE_PROBE_MODULE);
	ide_init_module(IDE_DRIVER_MODULE);
	return hwif->present ? index : -1;
}

void ide_add_setting(ide_drive_t *drive, const char *name, int rw, int read_ioctl, int write_ioctl, int data_type, int min, int max, int mul_factor, int div_factor, void *data, ide_procset_t *set)
{
	ide_settings_t **p = (ide_settings_t **) &drive->settings, *setting = NULL;

	while ((*p) && strcmp((*p)->name, name) < 0)
		p = &((*p)->next);
	if ((setting = kmalloc(sizeof(*setting), GFP_KERNEL)) == NULL)
		goto abort;
	memset(setting, 0, sizeof(*setting));
	if ((setting->name = kmalloc(strlen(name) + 1, GFP_KERNEL)) == NULL)
		goto abort;
	strcpy(setting->name, name);		setting->rw = rw;
	setting->read_ioctl = read_ioctl;	setting->write_ioctl = write_ioctl;
	setting->data_type = data_type;		setting->min = min;
	setting->max = max;			setting->mul_factor = mul_factor;
	setting->div_factor = div_factor;	setting->data = data;
	setting->set = set;			setting->next = *p;
	if (drive->driver)
		setting->auto_remove = 1;
	*p = setting;
	return;
abort:
	if (setting)
		kfree(setting);
}

void ide_remove_setting(ide_drive_t *drive, char *name)
{
	ide_settings_t **p = (ide_settings_t **) &drive->settings, *setting;

	while ((*p) && strcmp((*p)->name, name))
		p = &((*p)->next);
	if ((setting = (*p)) == NULL)
		return;
	(*p) = setting->next;
	kfree(setting->name);
	kfree(setting);
}

static ide_settings_t *ide_find_setting_by_ioctl(ide_drive_t *drive, int cmd)
{
	ide_settings_t *setting = drive->settings;

	while (setting) {
		if (setting->read_ioctl == cmd || setting->write_ioctl == cmd)
			break;
		setting = setting->next;
	}
	return setting;
}

ide_settings_t *ide_find_setting_by_name(ide_drive_t *drive, char *name)
{
	ide_settings_t *setting = drive->settings;

	while (setting) {
		if (strcmp(setting->name, name) == 0)
			break;
		setting = setting->next;
	}
	return setting;
}

static void auto_remove_settings(ide_drive_t *drive)
{
	ide_settings_t *setting;
repeat:
	setting = drive->settings;
	while (setting) {
		if (setting->auto_remove) {
			ide_remove_setting(drive, setting->name);
			goto repeat;
		}
		setting = setting->next;
	}
}

int ide_read_setting(ide_drive_t *drive, ide_settings_t *setting)
{
	int		val = -EINVAL;
	unsigned long	flags;

	if ((setting->rw & SETTING_READ)) {
		spin_lock_irqsave(&HWGROUP(drive)->spinlock, flags);
		switch(setting->data_type) {
			case TYPE_BYTE:
				val = *((u8 *) setting->data);
				break;
			case TYPE_SHORT:
				val = *((u16 *) setting->data);
				break;
			case TYPE_INT:
			case TYPE_INTA:
				val = *((u32 *) setting->data);
				break;
		}
		spin_unlock_irqrestore(&HWGROUP(drive)->spinlock, flags);
	}
	return val;
}

int ide_spin_wait_hwgroup (ide_drive_t *drive, unsigned long *flags)
{
	ide_hwgroup_t *hwgroup = HWGROUP(drive);
	unsigned long timeout = jiffies + (3 * HZ);

	spin_lock_irqsave(&hwgroup->spinlock, *flags);
	while (hwgroup->busy) {
		spin_unlock_irqrestore(&hwgroup->spinlock, *flags);
		__sti();	/* local CPU only; needed for jiffies */
		if (0 < (signed long)(jiffies - timeout)) {
			printk("%s: channel busy\n", drive->name);
			return -EBUSY;
		}
		spin_lock_irqsave(&hwgroup->spinlock, *flags);
	}
	return 0;
}

int ide_write_setting(ide_drive_t *drive, ide_settings_t *setting, int val)
{
	unsigned long flags;
	int i;
	u32 *p;

	if (!capable(CAP_SYS_ADMIN))
		return -EACCES;
	if (!(setting->rw & SETTING_WRITE))
		return -EPERM;
	if (val < setting->min || val > setting->max)
		return -EINVAL;
	if (setting->set)
		return setting->set(drive, val);
	if (ide_spin_wait_hwgroup(drive, &flags))
		return -EBUSY;
	switch (setting->data_type) {
		case TYPE_BYTE:
			*((u8 *) setting->data) = val;
			break;
		case TYPE_SHORT:
			*((u16 *) setting->data) = val;
			break;
		case TYPE_INT:
			*((u32 *) setting->data) = val;
			break;
		case TYPE_INTA:
			p = (u32 *) setting->data;
			for (i = 0; i < 1 << PARTN_BITS; i++, p++)
				*p = val;
			break;
	}
	spin_unlock_irqrestore(&HWGROUP(drive)->spinlock, flags);
	return 0;
}

static int set_io_32bit(ide_drive_t *drive, int arg)
{
	drive->io_32bit = arg;
#ifdef CONFIG_BLK_DEV_DTC2278
	if (HWIF(drive)->chipset == ide_dtc2278)
		HWIF(drive)->drives[!drive->select.b.unit].io_32bit = arg;
#endif /* CONFIG_BLK_DEV_DTC2278 */
	return 0;
}

static int set_using_dma(ide_drive_t *drive, int arg)
{
	if (!drive->driver || !DRIVER(drive)->supports_dma)
		return -EPERM;
	if (!drive->id || !(drive->id->capability & 1) || !HWIF(drive)->dmaproc)
		return -EPERM;
	if (HWIF(drive)->dmaproc(arg ? ide_dma_on : ide_dma_off, drive))
		return -EIO;
	return 0;
}

static int set_pio_mode(ide_drive_t *drive, int arg)
{
	struct request rq;

	if (!HWIF(drive)->tuneproc)
		return -ENOSYS;
	if (drive->special.b.set_tune)
		return -EBUSY;
	ide_init_drive_cmd(&rq);
	drive->tune_req = (byte) arg;
	drive->special.b.set_tune = 1;
	(void) ide_do_drive_cmd (drive, &rq, ide_wait);
	return 0;
}

void ide_add_generic_settings(ide_drive_t *drive)
{
/*
 *			drive	setting name		read/write access				read ioctl		write ioctl		data type	min	max				mul_factor	div_factor	data pointer			set function
 */
	ide_add_setting(drive,	"io_32bit",		drive->no_io_32bit ? SETTING_READ : SETTING_RW,	HDIO_GET_32BIT,		HDIO_SET_32BIT,		TYPE_BYTE,	0,	1 + (SUPPORT_VLB_SYNC << 1),	1,		1,		&drive->io_32bit,		set_io_32bit);
	ide_add_setting(drive,	"keepsettings",		SETTING_RW,					HDIO_GET_KEEPSETTINGS,	HDIO_SET_KEEPSETTINGS,	TYPE_BYTE,	0,	1,				1,		1,		&drive->keep_settings,		NULL);
	ide_add_setting(drive,	"nice1",		SETTING_RW,					-1,			-1,			TYPE_BYTE,	0,	1,				1,		1,		&drive->nice1,			NULL);
	ide_add_setting(drive,	"pio_mode",		SETTING_WRITE,					-1,			HDIO_SET_PIO_MODE,	TYPE_BYTE,	0,	255,				1,		1,		NULL,				set_pio_mode);
	ide_add_setting(drive,	"slow",			SETTING_RW,					-1,			-1,			TYPE_BYTE,	0,	1,				1,		1,		&drive->slow,			NULL);
	ide_add_setting(drive,	"unmaskirq",		drive->no_unmask ? SETTING_READ : SETTING_RW,	HDIO_GET_UNMASKINTR,	HDIO_SET_UNMASKINTR,	TYPE_BYTE,	0,	1,				1,		1,		&drive->unmask,			NULL);
	ide_add_setting(drive,	"using_dma",		SETTING_RW,					HDIO_GET_DMA,		HDIO_SET_DMA,		TYPE_BYTE,	0,	1,				1,		1,		&drive->using_dma,		set_using_dma);
}

int ide_wait_cmd (ide_drive_t *drive, int cmd, int nsect, int feature, int sectors, byte *buf)
{
	struct request rq;
	byte buffer[4];

	if (!buf)
		buf = buffer;
	memset(buf, 0, 4 + SECTOR_WORDS * 4 * sectors);
	ide_init_drive_cmd(&rq);
	rq.buffer = buf;
	*buf++ = cmd;
	*buf++ = nsect;
	*buf++ = feature;
	*buf++ = sectors;
	return ide_do_drive_cmd(drive, &rq, ide_wait);
}

static int ide_ioctl (struct inode *inode, struct file *file,
			unsigned int cmd, unsigned long arg)
{
	int err, major, minor;
	ide_drive_t *drive;
	struct request rq;
	kdev_t dev;
	ide_settings_t *setting;

	if (!inode || !(dev = inode->i_rdev))
		return -EINVAL;
	major = MAJOR(dev); minor = MINOR(dev);
	if ((drive = get_info_ptr(inode->i_rdev)) == NULL)
		return -ENODEV;

	if ((setting = ide_find_setting_by_ioctl(drive, cmd)) != NULL) {
		if (cmd == setting->read_ioctl) {
			err = ide_read_setting(drive, setting);
			return err >= 0 ? put_user(err, (long *) arg) : err;
		} else {
			if ((MINOR(inode->i_rdev) & PARTN_MASK))
				return -EINVAL;
			return ide_write_setting(drive, setting, arg);
		}
	}

	ide_init_drive_cmd (&rq);
	switch (cmd) {
		case HDIO_GETGEO:
		{
			struct hd_geometry *loc = (struct hd_geometry *) arg;
			if (!loc || (drive->media != ide_disk && drive->media != ide_floppy)) return -EINVAL;
			if (put_user(drive->bios_head, (byte *) &loc->heads)) return -EFAULT;
			if (put_user(drive->bios_sect, (byte *) &loc->sectors)) return -EFAULT;
			if (put_user(drive->bios_cyl, (unsigned short *) &loc->cylinders)) return -EFAULT;
			if (put_user((unsigned)drive->part[MINOR(inode->i_rdev)&PARTN_MASK].start_sect,
				(unsigned long *) &loc->start)) return -EFAULT;
			return 0;
		}
		case BLKFLSBUF:
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			fsync_dev(inode->i_rdev);
			invalidate_buffers(inode->i_rdev);
			return 0;

	 	case BLKGETSIZE:   /* Return device size */
			return put_user(drive->part[MINOR(inode->i_rdev)&PARTN_MASK].nr_sects, (long *) arg);

		case BLKRRPART: /* Re-read partition tables */
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			return ide_revalidate_disk(inode->i_rdev);

		case HDIO_OBSOLETE_IDENTITY:
		case HDIO_GET_IDENTITY:
			if (MINOR(inode->i_rdev) & PARTN_MASK)
				return -EINVAL;
			if (drive->id == NULL)
				return -ENOMSG;
			if (copy_to_user((char *)arg, (char *)drive->id, (cmd == HDIO_GET_IDENTITY) ? sizeof(*drive->id) : 142))
				return -EFAULT;
			return 0;

		case HDIO_GET_NICE:
			return put_user(drive->dsc_overlap	<<	IDE_NICE_DSC_OVERLAP	|
					drive->atapi_overlap	<<	IDE_NICE_ATAPI_OVERLAP	|
					drive->nice0		<< 	IDE_NICE_0		|
					drive->nice1		<<	IDE_NICE_1		|
					drive->nice2		<<	IDE_NICE_2,
					(long *) arg);
		case HDIO_DRIVE_CMD:
		{
			byte args[4], *argbuf = args;
			int argsize = 4;
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			if (NULL == (void *) arg)
				return ide_do_drive_cmd(drive, &rq, ide_wait);
			if (copy_from_user(args, (void *)arg, 4))
				return -EFAULT;
			if (args[3]) {
				argsize = 4 + (SECTOR_WORDS * 4 * args[3]);
				argbuf = kmalloc(argsize, GFP_KERNEL);
				if (argbuf == NULL)
					return -ENOMEM;
				memcpy(argbuf, args, 4);
			}
			err = ide_wait_cmd(drive, args[0], args[1], args[2], args[3], argbuf);
			if (copy_to_user((void *)arg, argbuf, argsize))
				err = -EFAULT;
			if (argsize > 4)
				kfree(argbuf);
			return err;
		}

		case HDIO_SCAN_HWIF:
		{
			int args[3];
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			if (copy_from_user(args, (void *)arg, 3 * sizeof(int)))
				return -EFAULT;
			if (ide_register(args[0], args[1], args[2]) == -1)
				return -EIO;
			return 0;
		}
	        case HDIO_UNREGISTER_HWIF:
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			/* should I check here for arg > MAX_HWIFS, or
			   just let ide_unregister fail silently? -- shaver */
			ide_unregister(arg);
			return 0;
		case HDIO_SET_NICE:
			if (!capable(CAP_SYS_ADMIN)) return -EACCES;
			if (drive->driver == NULL)
				return -EPERM;
			if (arg != (arg & ((1 << IDE_NICE_DSC_OVERLAP) | (1 << IDE_NICE_1))))
				return -EPERM;
			drive->dsc_overlap = (arg >> IDE_NICE_DSC_OVERLAP) & 1;
			if (drive->dsc_overlap && !DRIVER(drive)->supports_dsc_overlap) {
				drive->dsc_overlap = 0;
				return -EPERM;
			}
			drive->nice1 = (arg >> IDE_NICE_1) & 1;
			return 0;

		RO_IOCTLS(inode->i_rdev, arg);

		default:
			if (drive->driver != NULL)
				return DRIVER(drive)->ioctl(drive, inode, file, cmd, arg);
			return -EPERM;
	}
}

static int ide_check_media_change (kdev_t i_rdev)
{
	ide_drive_t *drive;

	if ((drive = get_info_ptr(i_rdev)) == NULL)
		return -ENODEV;
	if (drive->driver != NULL)
		return DRIVER(drive)->media_change(drive);
	return 0;
}

void ide_fixstring (byte *s, const int bytecount, const int byteswap)
{
	byte *p = s, *end = &s[bytecount & ~1]; /* bytecount must be even */

	if (byteswap) {
		/* convert from big-endian to host byte order */
		for (p = end ; p != s;) {
			unsigned short *pp = (unsigned short *) (p -= 2);
			*pp = ntohs(*pp);
		}
	}

	/* strip leading blanks */
	while (s != end && *s == ' ')
		++s;

	/* compress internal blanks and strip trailing blanks */
	while (s != end && *s) {
		if (*s++ != ' ' || (s != end && *s && *s != ' '))
			*p++ = *(s-1);
	}

	/* wipe out trailing garbage */
	while (p != end)
		*p++ = '\0';
}

/*
 * stridx() returns the offset of c within s,
 * or -1 if c is '\0' or not found within s.
 */
__initfunc(static int stridx (const char *s, char c))
{
	char *i = strchr(s, c);
	return (i && c) ? i - s : -1;
}

/*
 * match_parm() does parsing for ide_setup():
 *
 * 1. the first char of s must be '='.
 * 2. if the remainder matches one of the supplied keywords,
 *     the index (1 based) of the keyword is negated and returned.
 * 3. if the remainder is a series of no more than max_vals numbers
 *     separated by commas, the numbers are saved in vals[] and a
 *     count of how many were saved is returned.  Base10 is assumed,
 *     and base16 is allowed when prefixed with "0x".
 * 4. otherwise, zero is returned.
 */
__initfunc(static int match_parm (char *s, const char *keywords[], int vals[], int max_vals))
{
	static const char *decimal = "0123456789";
	static const char *hex = "0123456789abcdef";
	int i, n;

	if (*s++ == '=') {
		/*
		 * Try matching against the supplied keywords,
		 * and return -(index+1) if we match one
		 */
		if (keywords != NULL) {
			for (i = 0; *keywords != NULL; ++i) {
				if (!strcmp(s, *keywords++))
					return -(i+1);
			}
		}
		/*
		 * Look for a series of no more than "max_vals"
		 * numeric values separated by commas, in base10,
		 * or base16 when prefixed with "0x".
		 * Return a count of how many were found.
		 */
		for (n = 0; (i = stridx(decimal, *s)) >= 0;) {
			vals[n] = i;
			while ((i = stridx(decimal, *++s)) >= 0)
				vals[n] = (vals[n] * 10) + i;
			if (*s == 'x' && !vals[n]) {
				while ((i = stridx(hex, *++s)) >= 0)
					vals[n] = (vals[n] * 0x10) + i;
			}
			if (++n == max_vals)
				break;
			if (*s == ',' || *s == ';')
				++s;
		}
		if (!*s)
			return n;
	}
	return 0;	/* zero = nothing matched */
}

/*
 * ide_setup() gets called VERY EARLY during initialization,
 * to handle kernel "command line" strings beginning with "hdx="
 * or "ide".  Here is the complete set currently supported:
 *
 * "hdx="  is recognized for all "x" from "a" to "h", such as "hdc".
 * "idex=" is recognized for all "x" from "0" to "3", such as "ide1".
 *
 * "hdx=noprobe"	: drive may be present, but do not probe for it
 * "hdx=none"		: drive is NOT present, ignore cmos and do not probe
 * "hdx=nowerr"		: ignore the WRERR_STAT bit on this drive
 * "hdx=cdrom"		: drive is present, and is a cdrom drive
 * "hdx=cyl,head,sect"	: disk drive is present, with specified geometry
 * "hdx=autotune"	: driver will attempt to tune interface speed
 *				to the fastest PIO mode supported,
 *				if possible for this drive only.
 *				Not fully supported by all chipset types,
 *				and quite likely to cause trouble with
 *				older/odd IDE drives.
 *
 * "hdx=slow"		: insert a huge pause after each access to the data
 *				port. Should be used only as a last resort.
 *
 * "hdx=swapdata"	: when the drive is a disk, byte swap all data
 * "hdx=bswap"		: same as above..........
 *
 * "idebus=xx"		: inform IDE driver of VESA/PCI bus speed in MHz,
 *				where "xx" is between 20 and 66 inclusive,
 *				used when tuning chipset PIO modes.
 *				For PCI bus, 25 is correct for a P75 system,
 *				30 is correct for P90,P120,P180 systems,
 *				and 33 is used for P100,P133,P166 systems.
 *				If in doubt, use idebus=33 for PCI.
 *				As for VLB, it is safest to not specify it.
 *
 * "idex=noprobe"	: do not attempt to access/use this interface
 * "idex=base"		: probe for an interface at the addr specified,
 *				where "base" is usually 0x1f0 or 0x170
 *				and "ctl" is assumed to be "base"+0x206
 * "idex=base,ctl"	: specify both base and ctl
 * "idex=base,ctl,irq"	: specify base, ctl, and irq number
 * "idex=autotune"	: driver will attempt to tune interface speed
 *				to the fastest PIO mode supported,
 *				for all drives on this interface.
 *				Not fully supported by all chipset types,
 *				and quite likely to cause trouble with
 *				older/odd IDE drives.
 * "idex=noautotune"	: driver will NOT attempt to tune interface speed
 *				This is the default for most chipsets,
 *				except the cmd640.
 * "idex=serialize"	: do not overlap operations on idex and ide(x^1)
 * "idex=four"		: four drives on idex and ide(x^1) share same ports
 * "idex=reset"		: reset interface before first use
 * "idex=dma"		: enable DMA by default on both drives if possible
 *
 * The following are valid ONLY on ide0,
 * and the defaults for the base,ctl ports must not be altered.
 *
 * "ide0=dtc2278"	: probe/support DTC2278 interface
 * "ide0=ht6560b"	: probe/support HT6560B interface
 * "ide0=cmd640_vlb"	: *REQUIRED* for VLB cards with the CMD640 chip
 *			  (not for PCI -- automatically detected)
 * "ide0=qd6580"	: probe/support qd6580 interface
 * "ide0=ali14xx"	: probe/support ali14xx chipsets (ALI M1439, M1443, M1445)
 * "ide0=umc8672"	: probe/support umc8672 chipsets
 */
__initfunc(void ide_setup (char *s))
{
	int i, vals[3];
	ide_hwif_t *hwif;
	ide_drive_t *drive;
	unsigned int hw, unit;
	const char max_drive = 'a' + ((MAX_HWIFS * MAX_DRIVES) - 1);
	const char max_hwif  = '0' + (MAX_HWIFS - 1);

	printk("ide_setup: %s", s);
	init_ide_data ();

	/*
	 * Look for drive options:  "hdx="
	 */
	if (s[0] == 'h' && s[1] == 'd' && s[2] >= 'a' && s[2] <= max_drive) {
		const char *hd_words[] = {"none", "noprobe", "nowerr", "cdrom",
				"serialize", "autotune", "noautotune",
				"slow", "swapdata", "bswap", NULL};
		unit = s[2] - 'a';
		hw   = unit / MAX_DRIVES;
		unit = unit % MAX_DRIVES;
		hwif = &ide_hwifs[hw];
		drive = &hwif->drives[unit];
		if (strncmp(s + 4, "ide-", 4) == 0) {
			strncpy(drive->driver_req, s + 4, 9);
			goto done;
		}
		switch (match_parm(&s[3], hd_words, vals, 3)) {
			case -1: /* "none" */
				drive->nobios = 1;  /* drop into "noprobe" */
			case -2: /* "noprobe" */
				drive->noprobe = 1;
				goto done;
			case -3: /* "nowerr" */
				drive->bad_wstat = BAD_R_STAT;
				hwif->noprobe = 0;
				goto done;
			case -4: /* "cdrom" */
				drive->present = 1;
				drive->media = ide_cdrom;
				hwif->noprobe = 0;
				goto done;
			case -5: /* "serialize" */
				printk(" -- USE \"ide%d=serialize\" INSTEAD", hw);
				goto do_serialize;
			case -6: /* "autotune" */
				drive->autotune = 1;
				goto done;
			case -7: /* "noautotune" */
				drive->autotune = 2;
				goto done;
			case -8: /* "slow" */
				drive->slow = 1;
				goto done;
			case -9: /* swapdata or bswap */
			case -10:
				drive->bswap = 1;
				goto done;
			case 3: /* cyl,head,sect */
				drive->media	= ide_disk;
				drive->cyl	= drive->bios_cyl  = vals[0];
				drive->head	= drive->bios_head = vals[1];
				drive->sect	= drive->bios_sect = vals[2];
				drive->present	= 1;
				drive->forced_geom = 1;
				hwif->noprobe = 0;
				goto done;
			default:
				goto bad_option;
		}
	}

	if (s[0] != 'i' || s[1] != 'd' || s[2] != 'e')
		goto bad_option;
	/*
	 * Look for bus speed option:  "idebus="
	 */
	if (s[3] == 'b' && s[4] == 'u' && s[5] == 's') {
		if (match_parm(&s[6], NULL, vals, 1) != 1)
			goto bad_option;
		if (vals[0] >= 20 && vals[0] <= 66)
			idebus_parameter = vals[0];
		else
			printk(" -- BAD BUS SPEED! Expected value from 20 to 66");
		goto done;
	}
	/*
	 * Look for interface options:  "idex="
	 */
	if (s[3] >= '0' && s[3] <= max_hwif) {
		/*
		 * Be VERY CAREFUL changing this: note hardcoded indexes below
		 */
		const char *ide_words[] = {"noprobe", "serialize", "autotune", "noautotune", "reset", "dma", "four",
			"qd6580", "ht6560b", "cmd640_vlb", "dtc2278", "umc8672", "ali14xx", "dc4030", NULL};
		hw = s[3] - '0';
		hwif = &ide_hwifs[hw];
		i = match_parm(&s[4], ide_words, vals, 3);

		/*
		 * Cryptic check to ensure chipset not already set for hwif:
		 */
		if (i > 0 || i <= -7) {			/* is parameter a chipset name? */
			if (hwif->chipset != ide_unknown)
				goto bad_option;	/* chipset already specified */
			if (i <= -7 && hw != 0)
				goto bad_hwif;		/* chipset drivers are for "ide0=" only */
			if (i <= -7 && ide_hwifs[hw^1].chipset != ide_unknown)
				goto bad_option;	/* chipset for 2nd port already specified */
			printk("\n");
		}

		switch (i) {
#ifdef CONFIG_BLK_DEV_PDC4030
			case -14: /* "dc4030" */
			{
				extern void setup_pdc4030(ide_hwif_t *);
				setup_pdc4030(hwif);
				goto done;
			}
#endif /* CONFIG_BLK_DEV_PDC4030 */
#ifdef CONFIG_BLK_DEV_ALI14XX
			case -13: /* "ali14xx" */
			{
				extern void init_ali14xx (void);
				init_ali14xx();
				goto done;
			}
#endif /* CONFIG_BLK_DEV_ALI14XX */
#ifdef CONFIG_BLK_DEV_UMC8672
			case -12: /* "umc8672" */
			{
				extern void init_umc8672 (void);
				init_umc8672();
				goto done;
			}
#endif /* CONFIG_BLK_DEV_UMC8672 */
#ifdef CONFIG_BLK_DEV_DTC2278
			case -11: /* "dtc2278" */
			{
				extern void init_dtc2278 (void);
				init_dtc2278();
				goto done;
			}
#endif /* CONFIG_BLK_DEV_DTC2278 */
#ifdef CONFIG_BLK_DEV_CMD640
			case -10: /* "cmd640_vlb" */
			{
				extern int cmd640_vlb; /* flag for cmd640.c */
				cmd640_vlb = 1;
				goto done;
			}
#endif /* CONFIG_BLK_DEV_CMD640 */
#ifdef CONFIG_BLK_DEV_HT6560B
			case -9: /* "ht6560b" */
			{
				extern void init_ht6560b (void);
				init_ht6560b();
				goto done;
			}
#endif /* CONFIG_BLK_DEV_HT6560B */
#if CONFIG_BLK_DEV_QD6580
			case -8: /* "qd6580" */
			{
				extern void init_qd6580 (void);
				init_qd6580();
				goto done;
			}
#endif /* CONFIG_BLK_DEV_QD6580 */
#ifdef CONFIG_BLK_DEV_4DRIVES
			case -7: /* "four" drives on one set of ports */
			{
				ide_hwif_t *mate = &ide_hwifs[hw^1];
				mate->drives[0].select.all ^= 0x20;
				mate->drives[1].select.all ^= 0x20;
				hwif->chipset = mate->chipset = ide_4drives;
				mate->irq = hwif->irq;
				memcpy(mate->io_ports, hwif->io_ports, sizeof(hwif->io_ports));
				goto do_serialize;
			}
#endif /* CONFIG_BLK_DEV_4DRIVES */
			case -6: /* dma */
				hwif->autodma = 1;
				goto done;
			case -5: /* "reset" */
				hwif->reset = 1;
				goto done;
			case -4: /* "noautotune" */
				hwif->drives[0].autotune = 2;
				hwif->drives[1].autotune = 2;
				goto done;
			case -3: /* "autotune" */
				hwif->drives[0].autotune = 1;
				hwif->drives[1].autotune = 1;
				goto done;
			case -2: /* "serialize" */
			do_serialize:
				hwif->mate = &ide_hwifs[hw^1];
				hwif->mate->mate = hwif;
				hwif->serialized = hwif->mate->serialized = 1;
				goto done;

			case -1: /* "noprobe" */
				hwif->noprobe = 1;
				goto done;

			case 1:	/* base */
				vals[1] = vals[0] + 0x206; /* default ctl */
			case 2: /* base,ctl */
				vals[2] = 0;	/* default irq = probe for it */
			case 3: /* base,ctl,irq */
				ide_init_hwif_ports(hwif->io_ports, (ide_ioreg_t) vals[0], &hwif->irq);
				hwif->io_ports[IDE_CONTROL_OFFSET] = (ide_ioreg_t) vals[1];
				hwif->irq      = vals[2];
				hwif->noprobe  = 0;
				hwif->chipset  = ide_generic;
				goto done;

			case 0: goto bad_option;
			default:
				printk(" -- SUPPORT NOT CONFIGURED IN THIS KERNEL\n");
				return;
		}
	}
bad_option:
	printk(" -- BAD OPTION\n");
	return;
bad_hwif:
	printk("-- NOT SUPPORTED ON ide%d", hw);
done:
	printk("\n");
}

/*
 * This routine is called from the partition-table code in genhd.c
 * to "convert" a drive to a logical geometry with fewer than 1024 cyls.
 *
 * The second parameter, "xparm", determines exactly how the translation 
 * will be handled:
 *		 0 = convert to CHS with fewer than 1024 cyls
 *			using the same method as Ontrack DiskManager.
 *		 1 = same as "0", plus offset everything by 63 sectors.
 *		-1 = similar to "0", plus redirect sector 0 to sector 1.
 *		>1 = convert to a CHS geometry with "xparm" heads.
 *
 * Returns 0 if the translation was not possible, if the device was not 
 * an IDE disk drive, or if a geometry was "forced" on the commandline.
 * Returns 1 if the geometry translation was successful.
 */
int ide_xlate_1024 (kdev_t i_rdev, int xparm, const char *msg)
{
	ide_drive_t *drive;
	static const byte head_vals[] = {4, 8, 16, 32, 64, 128, 255, 0};
	const byte *heads = head_vals;
	unsigned long tracks;

	drive = get_info_ptr(i_rdev);
	if (!drive)
		return 0;

	if (drive->forced_geom) {
		/*
		 * Update the current 3D drive values.
		 */
		drive->id->cur_cyls	= drive->bios_cyl;
		drive->id->cur_heads	= drive->bios_head;
		drive->id->cur_sectors	= drive->bios_sect;
		return 0;
	}

	if (xparm > 1 && xparm <= drive->bios_head && drive->bios_sect == 63) {
		/*
		 * Update the current 3D drive values.
		 */
		drive->id->cur_cyls	= drive->bios_cyl;
		drive->id->cur_heads	= drive->bios_head;
		drive->id->cur_sectors	= drive->bios_sect;
		return 0;		/* we already have a translation */
	}

	printk("%s ", msg);

	if (xparm < 0 && (drive->bios_cyl * drive->bios_head * drive->bios_sect) < (1024 * 16 * 63)) {
		/*
		 * Update the current 3D drive values.
		 */
		drive->id->cur_cyls	= drive->bios_cyl;
		drive->id->cur_heads	= drive->bios_head;
		drive->id->cur_sectors	= drive->bios_sect;
		return 0;		/* small disk: no translation needed */
	}

	if (drive->id) {
		drive->cyl  = drive->id->cyls;
		drive->head = drive->id->heads;
		drive->sect = drive->id->sectors;
	}
	drive->bios_cyl  = drive->cyl;
	drive->bios_head = drive->head;
	drive->bios_sect = drive->sect;
	drive->special.b.set_geometry = 1;

	tracks = drive->bios_cyl * drive->bios_head * drive->bios_sect / 63;
	drive->bios_sect = 63;
	if (xparm > 1) {
		drive->bios_head = xparm;
		drive->bios_cyl = tracks / drive->bios_head;
	} else {
		while (drive->bios_cyl >= 1024) {
			drive->bios_head = *heads;
			drive->bios_cyl = tracks / drive->bios_head;
			if (0 == *++heads)
				break;
		}
#if FAKE_FDISK_FOR_EZDRIVE
		if (xparm == -1) {
			drive->remap_0_to_1 = 1;
			printk("[remap 0->1] ");
		} else
#endif /* FAKE_FDISK_FOR_EZDRIVE */
		if (xparm == 1) {
			drive->sect0 = 63;
			drive->bios_cyl = (tracks - 1) / drive->bios_head;
			printk("[remap +63] ");
		}
	}
	drive->part[0].nr_sects = current_capacity(drive);
	printk("[%d/%d/%d]", drive->bios_cyl, drive->bios_head, drive->bios_sect);
	/*
	 * Update the current 3D drive values.
	 */
	drive->id->cur_cyls    = drive->bios_cyl;
	drive->id->cur_heads   = drive->bios_head;
	drive->id->cur_sectors = drive->bios_sect;
	return 1;
}

/*
 * probe_for_hwifs() finds/initializes "known" IDE interfaces
 */
__initfunc(static void probe_for_hwifs (void))
{
#ifdef CONFIG_PCI
	if (pci_present())
	{
#ifdef CONFIG_BLK_DEV_IDEPCI
		ide_scan_pcibus();
#else
#ifdef CONFIG_BLK_DEV_RZ1000
		{
			extern void ide_probe_for_rz100x(void);
			ide_probe_for_rz100x();
		}
#endif /* CONFIG_BLK_DEV_RZ1000 */
#endif /* CONFIG_BLK_DEV_IDEPCI */
	}
#endif /* CONFIG_PCI */

#ifdef CONFIG_BLK_DEV_CMD640
	{
		extern void ide_probe_for_cmd640x(void);
		ide_probe_for_cmd640x();
	}
#endif /* CONFIG_BLK_DEV_CMD640 */
#ifdef CONFIG_BLK_DEV_PDC4030
	{
		extern int init_pdc4030(void);
		(void) init_pdc4030();
	}
#endif /* CONFIG_BLK_DEV_PDC4030 */
#ifdef CONFIG_BLK_DEV_IDE_PMAC
	{
		extern void pmac_ide_probe(void);
		pmac_ide_probe();
	}
#endif /* CONFIG_BLK_DEV_IDE_PMAC */
}

__initfunc(void ide_init_builtin_drivers (void))
{
	/*
	 * Probe for special PCI and other "known" interface chipsets
	 */
	probe_for_hwifs ();

#ifdef CONFIG_BLK_DEV_IDE
#if defined(__mc68000__) || defined(CONFIG_APUS)
	if (ide_hwifs[0].io_ports[IDE_DATA_OFFSET]) {
		ide_get_lock(&ide_lock, NULL, NULL);	/* for atari only */
		disable_irq(ide_hwifs[0].irq);
	}
#endif /* __mc68000__ || CONFIG_APUS */

	(void) ideprobe_init();

#if defined(__mc68000__) || defined(CONFIG_APUS)
	if (ide_hwifs[0].io_ports[IDE_DATA_OFFSET]) {
		enable_irq(ide_hwifs[0].irq);
		ide_release_lock(&ide_lock);	/* for atari only */
	}
#endif /* __mc68000__ || CONFIG_APUS */
#endif /* CONFIG_BLK_DEV_IDE */

#ifdef CONFIG_PROC_FS
	proc_ide_create();
#endif

	/*
	 * Attempt to match drivers for the available drives
	 */
#ifdef CONFIG_BLK_DEV_IDEDISK
	(void) idedisk_init();
#endif /* CONFIG_BLK_DEV_IDEDISK */
#ifdef CONFIG_BLK_DEV_IDECD
	(void) ide_cdrom_init();
#endif /* CONFIG_BLK_DEV_IDECD */
#ifdef CONFIG_BLK_DEV_IDETAPE
	(void) idetape_init();
#endif /* CONFIG_BLK_DEV_IDETAPE */
#ifdef CONFIG_BLK_DEV_IDEFLOPPY
	(void) idefloppy_init();
#endif /* CONFIG_BLK_DEV_IDEFLOPPY */
#ifdef CONFIG_BLK_DEV_IDESCSI
 #ifdef CONFIG_SCSI
	(void) idescsi_init();
 #else
    #warning ide scsi-emulation selected but no SCSI-subsystem in kernel
 #endif
#endif /* CONFIG_BLK_DEV_IDESCSI */
}

static int default_cleanup (ide_drive_t *drive)
{
	return ide_unregister_subdriver(drive);
}

static void default_do_request(ide_drive_t *drive, struct request *rq, unsigned long block)
{
	ide_end_request(0, HWGROUP(drive));
}
 
static void default_end_request (byte uptodate, ide_hwgroup_t *hwgroup)
{
	ide_end_request(uptodate, hwgroup);
}
  
static int default_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file,
			  unsigned int cmd, unsigned long arg)
{
	return -EIO;
}

static int default_open (struct inode *inode, struct file *filp, ide_drive_t *drive)
{
	drive->usage--;
	return -EIO;
}

static void default_release (struct inode *inode, struct file *filp, ide_drive_t *drive)
{
}

static int default_check_media_change (ide_drive_t *drive)
{
	return 1;
}

static void default_pre_reset (ide_drive_t *drive)
{
}

static unsigned long default_capacity (ide_drive_t *drive)
{
	return 0x7fffffff;	/* cdrom or tape */
}

static void default_special (ide_drive_t *drive)
{
	special_t *s = &drive->special;

	s->all = 0;
	drive->mult_req = 0;
}

static void setup_driver_defaults (ide_drive_t *drive)
{
	ide_driver_t *d = drive->driver;

	if (d->cleanup == NULL)		d->cleanup = default_cleanup;
	if (d->do_request == NULL)	d->do_request = default_do_request;
	if (d->end_request == NULL)	d->end_request = default_end_request;
	if (d->ioctl == NULL)		d->ioctl = default_ioctl;
	if (d->open == NULL)		d->open = default_open;
	if (d->release == NULL)		d->release = default_release;
	if (d->media_change == NULL)	d->media_change = default_check_media_change;
	if (d->pre_reset == NULL)	d->pre_reset = default_pre_reset;
	if (d->capacity == NULL)	d->capacity = default_capacity;
	if (d->special == NULL)		d->special = default_special;
}

ide_drive_t *ide_scan_devices (byte media, const char *name, ide_driver_t *driver, int n)
{
	unsigned int unit, index, i;

	for (index = 0; index < MAX_HWIFS; ++index)
		if (ide_hwifs[index].present) goto search;
	ide_init_module(IDE_PROBE_MODULE);
search:
	for (index = 0, i = 0; index < MAX_HWIFS; ++index) {
		ide_hwif_t *hwif = &ide_hwifs[index];
		if (!hwif->present)
			continue;
		for (unit = 0; unit < MAX_DRIVES; ++unit) {
			ide_drive_t *drive = &hwif->drives[unit];
			char *req = drive->driver_req;
			if (*req && !strstr(name, req))
				continue;
			if (drive->present && drive->media == media && drive->driver == driver && ++i > n)
				return drive;
		}
	}
	return NULL;
}

#ifdef CONFIG_PROC_FS
static ide_proc_entry_t generic_subdriver_entries[] = {
	{ "capacity",	S_IFREG|S_IRUGO,	proc_ide_read_capacity,	NULL },
	{ NULL, 0, NULL, NULL }
};
#endif

int ide_register_subdriver (ide_drive_t *drive, ide_driver_t *driver, int version)
{
	unsigned long flags;
	
	save_flags(flags);		/* all CPUs */
	cli();				/* all CPUs */
	if (version != IDE_SUBDRIVER_VERSION || !drive->present || drive->driver != NULL || drive->busy || drive->usage) {
		restore_flags(flags);	/* all CPUs */
		return 1;
	}
	drive->driver = driver;
	setup_driver_defaults(drive);
	restore_flags(flags);		/* all CPUs */
	if (drive->autotune != 2) {
		if (driver->supports_dma && HWIF(drive)->dmaproc != NULL)
			(void) (HWIF(drive)->dmaproc(ide_dma_check, drive));
		drive->dsc_overlap = (drive->next != drive && driver->supports_dsc_overlap);
		drive->nice1 = 1;
	}
	drive->revalidate = 1;
#ifdef CONFIG_PROC_FS
	ide_add_proc_entries(drive->proc, generic_subdriver_entries, drive);
	ide_add_proc_entries(drive->proc, driver->proc, drive);
#endif
	return 0;
}

int ide_unregister_subdriver (ide_drive_t *drive)
{
	unsigned long flags;
	
	save_flags(flags);		/* all CPUs */
	cli();				/* all CPUs */
	if (drive->usage || drive->busy || drive->driver == NULL || DRIVER(drive)->busy) {
		restore_flags(flags);	/* all CPUs */
		return 1;
	}
#ifdef CONFIG_PROC_FS
	ide_remove_proc_entries(drive->proc, DRIVER(drive)->proc);
	ide_remove_proc_entries(drive->proc, generic_subdriver_entries);
#endif
	auto_remove_settings(drive);
	drive->driver = NULL;
	restore_flags(flags);		/* all CPUs */
	return 0;
}

int ide_register_module (ide_module_t *module)
{
	ide_module_t *p = ide_modules;

	while (p) {
		if (p == module)
			return 1;
		p = p->next;
	}
	module->next = ide_modules;
	ide_modules = module;
	revalidate_drives();
	return 0;
}

void ide_unregister_module (ide_module_t *module)
{
	ide_module_t **p;

	for (p = &ide_modules; (*p) && (*p) != module; p = &((*p)->next));
	if (*p)
		*p = (*p)->next;
}

struct file_operations ide_fops[] = {{
	NULL,			/* lseek - default */
	block_read,		/* read - general block-dev read */
	block_write,		/* write - general block-dev write */
	NULL,			/* readdir - bad */
	NULL,			/* poll */
	ide_ioctl,		/* ioctl */
	NULL,			/* mmap */
	ide_open,		/* open */
	NULL,			/* flush */
	ide_release,		/* release */
	block_fsync,		/* fsync */
	NULL,			/* fasync */
	ide_check_media_change,	/* check_media_change */
	ide_revalidate_disk	/* revalidate */
}};

EXPORT_SYMBOL(ide_hwifs);
EXPORT_SYMBOL(ide_register_module);
EXPORT_SYMBOL(ide_unregister_module);
EXPORT_SYMBOL(ide_spin_wait_hwgroup);

/*
 * Probe module
 */
EXPORT_SYMBOL(ide_timer_expiry);
EXPORT_SYMBOL(ide_intr);
EXPORT_SYMBOL(ide_geninit);
EXPORT_SYMBOL(ide_fops);
EXPORT_SYMBOL(ide_get_queue);
EXPORT_SYMBOL(do_ide0_request);
EXPORT_SYMBOL(ide_add_generic_settings);
#if MAX_HWIFS > 1
EXPORT_SYMBOL(do_ide1_request);
#endif /* MAX_HWIFS > 1 */
#if MAX_HWIFS > 2
EXPORT_SYMBOL(do_ide2_request);
#endif /* MAX_HWIFS > 2 */
#if MAX_HWIFS > 3
EXPORT_SYMBOL(do_ide3_request);
#endif /* MAX_HWIFS > 3 */
#if MAX_HWIFS > 4
EXPORT_SYMBOL(do_ide4_request);
#endif /* MAX_HWIFS > 4 */
#if MAX_HWIFS > 5
EXPORT_SYMBOL(do_ide5_request);
#endif /* MAX_HWIFS > 5 */

/*
 * Driver module
 */
EXPORT_SYMBOL(ide_scan_devices);
EXPORT_SYMBOL(ide_register_subdriver);
EXPORT_SYMBOL(ide_unregister_subdriver);
EXPORT_SYMBOL(ide_input_data);
EXPORT_SYMBOL(ide_output_data);
EXPORT_SYMBOL(atapi_input_bytes);
EXPORT_SYMBOL(atapi_output_bytes);
EXPORT_SYMBOL(ide_set_handler);
EXPORT_SYMBOL(ide_dump_status);
EXPORT_SYMBOL(ide_error);
EXPORT_SYMBOL(ide_fixstring);
EXPORT_SYMBOL(ide_wait_stat);
EXPORT_SYMBOL(ide_do_reset);
EXPORT_SYMBOL(ide_init_drive_cmd);
EXPORT_SYMBOL(ide_do_drive_cmd);
EXPORT_SYMBOL(ide_end_drive_cmd);
EXPORT_SYMBOL(ide_end_request);
EXPORT_SYMBOL(ide_revalidate_disk);
EXPORT_SYMBOL(ide_cmd);
EXPORT_SYMBOL(ide_wait_cmd);
EXPORT_SYMBOL(ide_stall_queue);
#ifdef CONFIG_PROC_FS
EXPORT_SYMBOL(ide_add_proc_entries);
EXPORT_SYMBOL(ide_remove_proc_entries);
EXPORT_SYMBOL(proc_ide_read_geometry);
#endif
EXPORT_SYMBOL(ide_add_setting);
EXPORT_SYMBOL(ide_remove_setting);

EXPORT_SYMBOL(ide_register);
EXPORT_SYMBOL(ide_unregister);

/*
 * This is gets invoked once during initialization, to set *everything* up
 */
__initfunc(int ide_init (void))
{
	init_ide_data ();

	initializing = 1;
	ide_init_builtin_drivers();
	initializing = 0;

	return 0;
}

#ifdef MODULE
char *options = NULL;
MODULE_PARM(options,"s");

__initfunc(static void parse_options (char *line))
{
	char *next = line;

	if (line == NULL || !*line)
		return;
	while ((line = next) != NULL) {
 		if ((next = strchr(line,' ')) != NULL)
			*next++ = 0;
		if (!strncmp(line,"ide",3) || (!strncmp(line,"hd",2) && line[2] != '='))
			ide_setup(line);
	}
}

int init_module (void)
{
	parse_options(options);
	return ide_init();
}

void cleanup_module (void)
{
	int index;

	for (index = 0; index < MAX_HWIFS; ++index) {
		ide_unregister(index);
#ifdef CONFIG_BLK_DEV_IDEDMA
		if (ide_hwifs[index].dma_base)
			(void) ide_release_dma(&ide_hwifs[index]);
#endif /* CONFIG_BLK_DEV_IDEDMA */
	}
#ifdef CONFIG_PROC_FS
	proc_ide_destroy();
#endif
}
#endif /* MODULE */